PURE EDGE LIGHTING CW-SWMOD-TW-SCENE Pure Smart Switch Module Instruction Manual
- June 1, 2024
- Pure Edge Lighting
Table of Contents
PURE EDGE LIGHTING CW-SWMOD-TW-SCENE Pure Smart Switch Module
DESCRIPTION
The Pure Smart'” WiZ Pro Switch Module allows for integration of WiZ enabled lamps/fixtures/controls into any control system with self-reset switch panel or contact closure relays. The Pure Smart WiZ Pro Switch Module works by connecting to the relay pack in a home automation system, accepting the contact closure commands from the native system, and then sending out the associated wireless command to the WiZ device. There are 8 dry contact pins allowing for the following commands: On, Off, Dim Up, Dim Down, CCT Up, CCT Down, Previous Scene, and Next Scene. The switch module has a local communication protocol so it will function properly with or without wi-fi connectivity. Commissioning of the target device is accomplished with the WiZ app and then it can be controlled with the native automation system.
APPLICATIONS
Indoor, Dry locations only
POWER INPUT
9-40V Input
SELV Constant Voltage Input Only
EFFICIENCY
90%
AMBIENT OPERATING TEMPERATURE
-20° C to 45° C
LIFETIME
50,000 hours
INSTALLATION
Intended for installation behind compatible programmable key pads or near the
system relay panels.
CONNECTIVITY
Wi-Fi iEEE802.11 b/g/n
WIRE DEFINITION
NETWORK TOPOLOGY & WIRING DIAGRAMS
PURE SMART SYSTEM INTEGRATOR FOR WiZ PRO
LUTRON RELAY DRY CONTACT CLOSURE WIRING
LIGHTING CONTROL SYSTEMS PROGRAMMABLE KEY PADS
LUTRON WITH RADIO RA 3 RELAY DRY CONTACT CLOSURE WIRING
LIGHTING CONTROL SYSTEMS PROGRAMMABLE KEY PADS
VANTAGE RELAY DRY CONTACT CLOSURE WIRING
LIGHTING CONTROL SYSTEMS PROGRAMMABLE KEY PADS
CRESTRON RELAY DRY CONTACT CLOSURE WIRING
LIGHTING CONTROL SYSTEMS PROGRAMMABLE KEY PADS
ELAN/NICE RELAY DRY CONTACT CLOSURE WIRING
UGHTING CONTROL SYSTEMS PROGRAMMABLE KEY PADS
ELAN/NICE RELAY DRY CONTACT CLOSURE WIRING
black Pantone 2995C/CP
Size: 420 x 297 mm
Material: 80G writing paper
Dismantling method: organ page 105 x 49.5 mm finished product
Section 3. App Pairing
Downloading WiZ App V2:
- Please scan the QR code to download the application “WiZ App V2”.
- You may also find the WiZ app in the Apple App Store or the Google Play Store under “WiZ App V2”.
- After you download the WiZ Connected App and register a new account, please follow the instructions below to set up your smart switch.
For WiZ Pro Dashboard Users: WiZ Pro Dashboard account and home must be created before starting commissioning in the WiZ app. Please create an account on WiZ Pro Dashboard. Then create your home or location. After doing so, you may proceed to create an invitation in the dashboard by going to “settings” and then the “members” tab. By clicking on the “Invite” button you will be able to generate an invitation to access this dashboard location in the WiZ app. From there you can proceed with commissioning in the WiZ app but also have the added functionality of the Dashboard desktop application.
PLEASE READ BEFORE PAIRING ROOM CONTROLLER IN WiZ APP:
In the WiZ app, any Pure Smart/ WiZ Connected fixture(s) must be added to a
room prior to adding the Room Controller that will control them. Please refer
to the installation manual included with the Pure Smart/ WiZ Connected light
fixtures for setup.
Connected by
FCC
ID:2A9YKCWSWMODTWSCENE
Smart Pairing
-
Once your lamps or fixtures have been connected, press the plus sign in the top right hand corner to add your smart switch module.
-
Select ”Wall Controller” from the available device types.
-
Select whichever room the switch module will be installed in or controlling.
-
Follow the on-screen instructions and ensure that your switch module is connected to 9-40V power and then press ”START”.
-
Follow the on-screen instructions by pressing the On button on your resettable switch panel or relay and wait while the WiZ app looks for your Switch Module.
-
When you receive the ”Accessory found” message you may press done and begin controlling the light fixtures in that room with your Resettable switch panel or relay. Follow additional instructions below to personalize.
Additional Settings for Wall Controller Accessory
-
For additional setup, select “Settings” on the bottom right hand corner of the Home screen.
-
Select “Accessories” from the Settings menu.
-
Select the Wall Controller that you’d like to customize control with.
-
If needed, you have the option to rename your Switch.
-
You can select individual targets that the Wall Controller will control by choosing specific fixtures or devices.
-
Or you can choose an entire room for the Wall Controller to control.
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
CAUTION – PLEASE READ!
This device is intended for installation in accordance with the National
Electric Code and local regulations in the United States, or the Canadian
Electrical Code and local regulations in Canada. If you are unsure or
uncomfortable about performing this installation consult a qualified
electrician.
WARNING – SHOCK HAZARD
TURN OFF THE POWER to the circuit for the switch and lighting fixture at
the service panel (circuit breaker) prior to installation.
ALL WIRING CONNECTIONS MUST BE MADE WITH THE POWER OFF to avoid personal
injury and/or damage to the switch.
OTHER WARNINGS
Risk of Fire
Risk of Electrical Shock
Risk of Burns
V 1.0
WiZ Pro Software Suit
WiZ Pro Dashboard
- Grant access permission to different stakeholders.
- A clear overview to monitor lights with their mapped location.
- Full range of configurations and remote control.
- Comprehensive reporting on device status.
WiZ Pro Setup
- An interface dedicated to Installers
- Extends capabilities of installation of WiZ Pro products
WiZ App
- For end users to have simple, quick control on a daily basis.
- Rich features including Scenes and Rhythms.
IC Caution.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Customer Support
www.PureEdgeLighting.com | Phone:
773.770.1195 | 1718 W. Fullerton Ave. Chicago, IL 60614
PureEdge Lighting reserves the right to modify this specification without
prior notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>