Lenovo PX ThinkStation Workstation User Guide
- June 15, 2024
- Lenovo
Table of Contents
- PX ThinkStation Workstation
- Product Information: PX Hardware
- Specifications
- Chapter 1. Important Safety Information
- General Safety
- Electrical Safety
- Safety Inspection Guide
- Handling Electrostatic Discharge-Sensitive Devices
- Grounding Requirements
- Safety Notices (Multi-Lingual Translations)
- Strategy for Replacing FRUs
- Strategy for Replacing a Hard Disk Drive or a Solid-State
- Important Notice for Replacing a System Board
- How to Use Error Codes
- Strategy for Replacing FRUs for CTO, Special-Bid, and Standard
- Product Definition
- FRU Identification
- Notices for Side Ventilation and Workplace Power
- Front
- Rear
- Service Checkout
- Problem Determination Tips
- Symptom-to-FRU Index
- Hard Disk Drive Boot Error
- Power Supply Problems
- Beep Symptoms
- POST Error Codes
- Miscellaneous Error Conditions
- Undetermined Problems
- Recover from a BIOS Update Failure
- Clear CMOS
- What is RAID
- Configure RAID with Intel RSTe
- Configure RAID with AVAGO MegaRAID Configuration Utility
- Configure RAID with Intel Virtual RAID on CPU
- Basic Procedure for Resolving Computer Problems
- UEFI Diagnostic Program
- Diagnostics
- Self-Help Resources
- Handling Static-Sensitive Devices
- Service Tool Kit
- Major FRUs and CRUs
- System Board
- Expand Your Computer
- Removing and Installing Hardware
PX ThinkStation Workstation
Product Information: PX Hardware
Specifications
- Third Edition (December 2023)
Chapter 1. Important Safety Information
General Safety
The PX Hardware is designed with user safety in mind. Please
follow these general safety guidelines:
-
Read and understand all instructions before using the
product. -
Keep the product away from water and other liquids.
-
Avoid using the product near open flames or heat sources.
-
Do not expose the product to extreme temperatures.
Electrical Safety
To ensure electrical safety while using the PX Hardware, please
adhere to the following guidelines:
- Use only the provided power adapter and cables.
- Do not overload electrical outlets or extension cords.
- Avoid using the product in wet or damp conditions.
- Unplug the product during thunderstorms or when not in use for
an extended period.
Safety Inspection Guide
Prior to using the PX Hardware, perform a safety inspection
using the guide provided in the user manual. This will help
identify any potential hazards or issues that may affect the safe
operation of the product.
Handling Electrostatic Discharge-Sensitive Devices
When handling electrostatic discharge-sensitive devices, take
the following precautions:
- Wear an anti-static wrist strap.
- Avoid touching sensitive components with bare hands.
- Work on a grounded surface, such as an anti-static mat.
Grounding Requirements
Proper grounding is essential for the safe operation of the PX
Hardware. Ensure that the product is connected to a properly
grounded power source.
Safety Notices (Multi-Lingual Translations)
The user manual includes safety notices in multiple languages.
Refer to these notices for additional safety information and
guidelines.
Chapter 2. Important Service Information
Strategy for Replacing FRUs
Follow the recommended strategy for replacing Field Replaceable
Units (FRUs) to ensure proper installation and functionality of the
PX Hardware.
Strategy for Replacing a Hard Disk Drive or a Solid-State
Drive
If you need to replace a hard disk drive or a solid-state drive,
refer to the specific instructions provided in the user manual.
These instructions will guide you through the replacement process
step by step.
Important Notice for Replacing a System Board
Replacing a system board requires special attention. Read the
important notice provided in the user manual before attempting to
replace the system board of the PX Hardware.
How to Use Error Codes
If you encounter error codes while using the PX Hardware, refer
to the user manual for instructions on how to interpret and
troubleshoot these codes.
Strategy for Replacing FRUs for CTO, Special-Bid, and Standard
Models
For CTO (Configure-to-Order), special-bid, and standard models
of the PX Hardware, follow the specific strategy outlined in the
user manual for replacing FRUs.
Product Definition
The PX Hardware is defined as a high-performance computing
device designed for various applications. Refer to the user manual
for detailed specifications and capabilities of the product.
FRU Identification
When replacing Field Replaceable Units (FRUs) in the PX
Hardware, it is important to correctly identify the FRU. The user
manual provides information on how to identify different FRUs.
Chapter 3. Product Overview
Notices for Side Ventilation and Workplace Power
Ensure proper side ventilation and workplace power for the PX
Hardware. Follow the notices provided in the user manual to
optimize performance and prevent overheating.
Front
The front of the PX Hardware features various ports, buttons,
and indicators. Refer to the user manual for a detailed description
of the front panel and its functions.
Rear
The rear of the PX Hardware includes additional ports and
connectors. Consult the user manual for a comprehensive overview of
the rear panel and its functionalities.
Chapter 4. Service Checkout and Symptom-to-FRU Index
Service Checkout
If you encounter any issues with the PX Hardware, perform a
service checkout using the instructions provided in the user
manual. This will help diagnose and resolve common problems.
Problem Determination Tips
Refer to the user manual for problem determination tips specific
to the PX Hardware. These tips will assist you in identifying and
resolving various hardware-related issues.
Symptom-to-FRU Index
The symptom-to-FRU index in the user manual provides a
comprehensive list of common symptoms and their corresponding Field
Replaceable Units (FRUs). Use this index to troubleshoot specific
issues with the PX Hardware.
Hard Disk Drive Boot Error
If you encounter a hard disk drive boot error, refer to the user
manual for troubleshooting steps and potential solutions.
Power Supply Problems
If you experience power supply problems with the PX Hardware,
consult the user manual for troubleshooting tips and instructions
on resolving these issues.
Beep Symptoms
The PX Hardware may emit beep sounds to indicate specific
issues. Refer to the user manual for a beep symptom guide to help
identify the cause of the beeping and take appropriate action.
POST Error Codes
If you receive POST (Power-On Self-Test) error codes, consult
the user manual for a comprehensive list of error codes and their
meanings. This will assist in troubleshooting and resolving the
issue.
Miscellaneous Error Conditions
In case of miscellaneous error conditions not covered by other
sections, refer to the user manual for guidance on identifying and
resolving these errors.
Undetermined Problems
If you encounter problems with the PX Hardware that cannot be
easily identified or resolved, follow the instructions provided in
the user manual for further assistance.
Recover from a BIOS Update Failure
If a BIOS update fails or causes issues with the PX Hardware,
the user manual provides instructions on how to recover from this
failure and restore the system to its previous state.
Clear CMOS
To clear the CMOS (Complementary Metal-Oxide-Semiconductor)
settings of the PX Hardware, follow the step-by-step instructions
provided in the user manual.
Chapter 5. RAID
What is RAID
The user manual explains the concept of RAID (Redundant Array of
Independent Disks) and its benefits. Refer to this section for a
detailed explanation of RAID technology.
Configure RAID with Intel RSTe
If you want to configure RAID using Intel RSTe (Rapid Storage
Technology enterprise) software, follow the instructions provided
in the user manual for a step-by-step guide.
Configure RAID with AVAGO MegaRAID Configuration Utility
If you prefer to configure RAID using the AVAGO MegaRAID
Configuration Utility, refer to the user manual for detailed
instructions on how to set up RAID using this utility.
Configure RAID with Intel Virtual RAID on CPU
The user manual provides instructions on configuring RAID using
Intel Virtual RAID on CPU (VROC) technology. Follow these
instructions for setting up RAID using VROC.
Chapter 6. Diagnostics
Basic Procedure for Resolving Computer Problems
If you encounter computer problems while using the PX Hardware,
follow the basic procedure outlined in the user manual to diagnose
and resolve these issues.
UEFI Diagnostic Program
The user manual provides information on how to access and use
the UEFI (Unified Extensible Firmware Interface) diagnostic
program. This program can help identify and troubleshoot hardware
problems.
Diagnostics
The PX Hardware comes with built-in diagnostic tools. Refer to
the user manual for instructions on how to access and use these
diagnostics to test and troubleshoot the hardware components.
Self-Help Resources
In addition to the user manual, there are self-help resources
available for troubleshooting PX Hardware issues. Consult the user
manual for a list of these resources and how to access them.
Chapter 7. Hardware Removal and Installation
Handling Static-Sensitive Devices
When handling static-sensitive devices during hardware removal
and installation, take the necessary precautions outlined in the
user manual to prevent damage to the components.
Service Tool Kit
A service tool kit is recommended for proper hardware removal
and installation. Refer to the user manual for a list of essential
tools and their usage in servicing the PX Hardware.
Major FRUs and CRUs
The user manual provides a list of major Field Replaceable Units
(FRUs) and Customer Replaceable Units (CRUs) in the PX Hardware.
This list will help you identify and replace these components when
necessary.
System Board
If you need to remove or replace the system board of the PX
Hardware, consult the user manual for detailed instructions and
precautions to ensure a successful operation.
Expand Your Computer
The PX Hardware can be expanded with additional hardware
components. The user manual provides guidance on how to expand your
computer’s capabilities by installing compatible components.
Removing and Installing Hardware
For step-by-step instructions on removing and installing various
hardware components, refer to
PX Hardware Maintenance Manual
Third Edition (December 2023)
© Copyright Lenovo 2023. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or
software is delivered pursuant to a General Services Administration “GSA”
contract, use, reproduction, or disclosure is subject to restrictions set
forth in Contract No. GS35F-05925.
Contents
Chapter 1. Important safety information . . . . . . . . . . . . . . . . 1
General safety . . . . . . . . . . . . . . . . 1 Electrical safety . . . . . .
. . . . . . . . . . 2 Safety inspection guide . . . . . . . . . . . . . 3
Handling electrostatic discharge-sensitive devices . . . . . . . . . . . . . .
. . . . . 4 Grounding requirements . . . . . . . . . . . . 4 Safety notices
(multi-lingual translations) . . . . . . 4
Chapter 2. Important service information . . . . . . . . . . . . . . . 27
Strategy for replacing FRUs . . . . . . . . . . 27 Strategy for replacing a
hard disk drive or a solid-state drive . . . . . . . . . . . . . 27 Important
notice for replacing a system board . . . . . . . . . . . . . . . . . 27 How
to use error codes . . . . . . . . . . 28
Strategy for replacing FRUs for CTO, special-bid, and standard models. . . . .
. . . . . . . . 28
Product definition . . . . . . . . . . . . 28 FRU identification . . . . . . .
. . . . . 28
Chapter 3. Product overview . . . . . 29
Notices for side ventilation and workplace power . . . . . . . . . . . . . . .
. . . 29 Front . . . . . . . . . . . . . . . . . . . 31 Rear . . . . . . . . .
. . . . . . . . . . 34
Chapter 4. Service checkout and symptom-to-FRU index . . . . . . . . 37
Service checkout . . . . . . . . . . . . . . 37 Problem determination tips . .
. . . . . . 37
Symptom-to-FRU index . . . . . . . . . . . 38 Hard disk drive boot error . . .
. . . . . . 38 Power supply problems . . . . . . . . . . 39 Beep symptoms . .
. . . . . . . . . . . 39 POST error codes . . . . . . . . . . . . 40
Miscellaneous error conditions . . . . . . . 41 Undetermined problems . . . .
. . . . . 43 Recover from a BIOS update failure . . . . . 43 Clear CMOS . . .
. . . . . . . . . . . 44
Chapter 5. RAID . . . . . . . . . . . . 45
What is RAID . . . . . . . . . . . . . . . . 45 Configure RAID with Intel
RSTe. . . . . . . . . 45 Configure RAID with AVAGO MegaRAID Configuration
Utility . . . . . . . . . . . . . 46 Configure RAID with Intel Virtual RAID on
CPU . . . 48
© Copyright Lenovo 2023
Chapter 6. Diagnostics . . . . . . . . 51
Basic procedure for resolving computer problems . . . . . . . . . . . . . . .
. . 51 UEFI diagnostic program . . . . . . . . . . . 51 Diagnostics . . . . .
. . . . . . . . . . . 52 Self-help resources . . . . . . . . . . . . . 53
Chapter 7. Hardware removal and installation . . . . . . . . . . . . . . . 55
Handling static-sensitive devices . . . . . . . . 55 Service tool kit . . . .
. . . . . . . . . . . 55 Major FRUs and CRUs . . . . . . . . . . . . 57 System
board . . . . . . . . . . . . . . . 60 Expand your computer . . . . . . . . .
. . . 64 Removing and installing hardware . . . . . . . 64
External options . . . . . . . . . . . . . 65 ThinkStation logo badge . . . .
. . . . . 65 ID badge. . . . . . . . . . . . . . . . 65 Dummy cover for the
upper PSU bay. . . . . 66 Power supply assembly . . . . . . . . . . 67 Top
cover . . . . . . . . . . . . . . . 68 Front and rear Wi-Fi antenna . . . . .
. . . 69 Wi-Fi antenna cover . . . . . . . . . . . 72 Left side cover . . . .
. . . . . . . . . 72 NVLINK retainer . . . . . . . . . . . . . 74 CPU duct . .
. . . . . . . . . . . . . 75 Wi-Fi card adapter . . . . . . . . . . . . 75 Wi-
Fi card . . . . . . . . . . . . . . . 78 Front fan assembly. . . . . . . . . .
. . 79 NVLINK bridge . . . . . . . . . . . . . 80 Front fan bracket . . . . .
. . . . . . . 81 Thermal sensor . . . . . . . . . . . . . 83 Rear fan assembly
. . . . . . . . . . . . 83 Blank bezel. . . . . . . . . . . . . . . 84 Front
panel IO assembly . . . . . . . . . 85 Lock kit for the front access bay . . .
. . . 86 Think LED holder and cable . . . . . . . . 88 Lock kit for the left
side cover . . . . . . . 89 Hard disk drive in the front access bay . . . . 92
Hard disk drive in the PSU bay storage enclosure . . . . . . . . . . . . . . .
95 Right side cover . . . . . . . . . . . . . 97 Cover presence switches . . .
. . . . . . 99 Power distribution board and bracket . . . . 101 BCB board and
bracket . . . . . . . . . . 102 Storage fan assembly. . . . . . . . . . . 103
M.2 solid-state drive in the front access bay . . . . . . . . . . . . . . . .
. . 104 Dual M.2 SSD enclosure . . . . . . . . . 106
i
Onboard M.2 solid-state drive and its heatsink kit . . . . . . . . . . . . . . . . . . 107 Memory fan . . . . . . . . . . . . . . 109 Memory module . . . . . . . . . . . . . 110 PCIe bracket . . . . . . . . . . . . . . 113 PCIe card . . . . . . . . . . . . . . . 114 Full-length PCIe card . . . . . . . . . . . 117 M.2 solid-state drive on an M.2 solid-state drive PCIe adapter . . . . . . . . . . . . 120 Super capacitor module . . . . . . . . . . 124
CPU heatsink . . . . . . . . . . . . . . 125 CPU and its carrier . . . . . . .
. . . . . 127 System board . . . . . . . . . . . . . . 130 Speaker . . . . . .
. . . . . . . . . . 131 Rear power button . . . . . . . . . . . . 132 Cable
connection . . . . . . . . . . . . 132
Chapter 8. Notices and trademarks . . . . . . . . . . . . . . .137
ii PX Hardware Maintenance Manual
About this manual
This manual provides service and reference information for ThinkStation®
computers listed on the front cover. Illustrations in this manual might look
different from your product. Use this manual along with the advanced
diagnostic tests to troubleshoot problems. Important: This manual is intended
only for trained service technicians who are familiar with ThinkStation
computers. Use this manual along with the advanced diagnostic tests to
troubleshoot problems effectively. Before servicing a ThinkStation computer,
be sure to read and understand Chapter 1 “Important safety information” on
page 1.
Chapter 1. Important safety information
General safety
Follow these rules to ensure general safety: · Observe good housekeeping in
the area of the machines during and after maintenance. · When lifting any
heavy object:
1. Ensure you can stand safely without slipping. 2. Distribute the weight of
the object equally between your feet. 3. Use a slow lifting force. Never move
suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing
up with your leg muscles; this action removes the strain from the
muscles in your back.
Attention: Do not attempt to lift any objects that weigh more than 16 kg (35
lb) or objects that you think are too heavy for you. · Do not perform any
action that causes hazards to the customer, or that makes the equipment
unsafe. · Before you start the machine, ensure that other service
representatives and the customer’s personnel are not in a hazardous position.
· Place removed covers and other parts in a safe place, away from all
personnel, while you are servicing the machine. · Keep your tool case away
from walk areas so that other people will not trip over it. · Do not wear
loose clothing that can be trapped in the moving parts of a machine. Ensure
that your sleeves are fastened or rolled up above your elbows. If your hair is
long, fasten it. · Insert the ends of your necktie or scarf inside clothing or
fasten it with a nonconductive clip, approximately 8 centimeters (3 inches)
from the end. · Do not wear jewelry, chains, metal-frame eyeglasses, or metal
fasteners for your clothing. Remember: Metal objects are good electrical
conductors. · Wear safety glasses when you are: hammering, drilling,
soldering, cutting wire, attaching springs, using solvents, or working in any
other conditions that might be hazardous to your eyes. · After service,
reinstall all safety shields, guards, labels, and ground wires. Replace any
safety device that is worn or defective. · Reinstall all covers correctly
before returning the machine to the customer.
CAUTION:
Keep fingers and other parts of your body away from hazardous, moving parts.
If you suffer an injury, seek medical care immediately.
CAUTION:
Avoid contact with hot components inside the computer. During operation, some
components become hot enough to burn the skin. Before you open the computer
cover, turn off the computer, disconnect power, and wait approximately 10
minutes for the components to cool.
© Copyright Lenovo 2023
1
Electrical safety
CAUTION: Electrical current from power, telephone, and communication cables
can be hazardous. To avoid personal injury or equipment damage, disconnect the
attached power cords, telecommunication systems, networks, and modems before
you open the computer covers, unless instructed otherwise in the installation
and configuration procedures.
Observe the following rules when working on electrical equipment.
Important: Use only approved tools and test equipment. Some hand tools have
handles covered with a soft material that does not insulate you when working
with live electrical currents. Many customers have, near their equipment,
rubber floor mats that contain small conductive fibers to decrease
electrostatic discharges. Do not use this type of mat to protect yourself from
electrical shock.
· Find the room emergency power-off (EPO) switch, disconnecting switch, or
electrical outlet. If an electrical accident occurs, you can then operate the
switch or unplug the power cord quickly.
· Do not work alone under hazardous conditions or near equipment that has
hazardous voltages. · Disconnect all power before:
Performing a mechanical inspection Working near power supplies Removing
or installing Field Replaceable Units (FRUs) · Before you start to work on the
machine, unplug the power cord. If you cannot unplug it, ask the customer to
power-off the wall box that supplies power to the machine and to lock the wall
box in the off position. · If you need to work on a machine that has exposed
electrical circuits, observe the following precautions:
Ensure that another person, familiar with the power-off controls, is near
you. Remember: Another person must be there to switch off the power, if
necessary.
Use only one hand when working with powered-on electrical equipment; keep
the other hand in your pocket or behind your back. Remember: There must be a
complete circuit to cause electrical shock. By observing the above rule, you
may prevent a current from passing through your body.
When using a tester, set the controls correctly and use the approved probe
leads and accessories for that tester.
Stand on suitable rubber mats (obtained locally, if necessary) to insulate
you from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
these instructions are in the safety sections of maintenance information. Use
extreme care when measuring high voltages. · Regularly inspect and maintain
your electrical hand tools for safe operational condition. · Do not use worn
or broken tools and testers. · Never assume that power has been disconnected
from a circuit. First, check that it has been powered-off. · Always look
carefully for possible hazards in your work area. Examples of these hazards
are moist floors, nongrounded power extension cables, power surges, and
missing safety grounds. · Do not touch live electrical circuits with the
reflective surface of a plastic dental mirror. The surface is conductive; such
touching can cause personal injury and machine damage. · Do not service the
following parts with the power on when they are removed from their normal
operating places in a machine:
2 PX Hardware Maintenance Manual
Power supply units Pumps Blowers and fans Motor generators and similar
units. (This practice ensures correct grounding of the units.) · If an
electrical accident occurs: Use caution; do not become a victim yourself.
Switch off power. Send another person to get medical aid.
Safety inspection guide
The intent of this inspection guide is to assist you in identifying
potentially unsafe conditions on these products. Each machine, as it was
designed and built, had required safety items installed to protect users and
service personnel from injury. This guide addresses only those items. However,
good judgment should be used to identify potential safety hazards due to
attachment of features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the
apparent hazard could be and whether you can continue without first correcting
the problem.
Consider these conditions and the safety hazards they present: · Electrical
hazards, especially primary power (primary voltage on the frame can cause
serious or fatal
electrical shock). · Explosive hazards, such as a damaged CRT face or bulging
capacitor · Mechanical hazards, such as loose or missing hardware
The guide consists of a series of steps presented in a checklist. Begin the
checks with the power off, and the power cord disconnected.
Checklist: 1. Check exterior covers for damage (loose, broken, or sharp
edges). 2. Power-off the computer. Disconnect the power cord. 3. Check the
power cord for: a. A third-wire ground connector in good condition. Use a
meter to measure third-wire ground continuity for 0.1 ohm or less between the
external ground pin and frame ground. b. The power cord should be the
appropriate type as specified in the parts listings. c. Insulation must not be
frayed or worn. 4. Remove the cover. 5. Check for any obvious alterations. Use
good judgment as to the safety of any alterations. 6. Check inside the unit
for any obvious unsafe conditions, such as metal filings, contamination, water
or other liquids, or signs of fire or smoke damage. 7. Check for worn, frayed,
or pinched cables. 8. Check that the power-supply cover fasteners (screws or
rivets) have not been removed or tampered with.
Chapter 1. Important safety information 3
Handling electrostatic discharge-sensitive devices
Any computer part containing transistors or integrated circuits (ICs) should
be considered sensitive to electrostatic discharge (ESD). ESD damage can occur
when there is a difference in charge between objects. Protect against ESD
damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.
Notes: 1. Use product-specific ESD procedures when they exceed the
requirements noted here. 2. Make sure that the ESD protective devices you use
have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts: · Keep the parts in protective packages
until they are inserted into the product. · Avoid contact with other people
while handling the part. · Wear a grounded wrist strap against your skin to
eliminate static on your body. · Prevent the part from touching your clothing.
Most clothing is insulative and retains a charge even when
you are wearing a wrist strap. · Use the black side of a grounded work mat to
provide a static-free work surface. The mat is especially
useful when handling ESD-sensitive devices. · Select a grounding system, such
as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system is desirable but not required to protect
against ESD damage. Attach the ESD ground clip to any frame ground, ground
braid, or green-wire ground. Use an ESD common ground or reference point
when working on a double-insulated or battery-
operated system. You can use coax or connector-outside shells on these
systems. Use the round ground-prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and
correct system function. Proper grounding of the electrical outlet can be
verified by a certified electrician.
Safety notices (multi-lingual translations)
The caution and danger safety notices in this section are provided in the
following languages: · English · Arabic · Brazilian/Portuguese · Chinese
(simplified) · Chinese (traditional) · French · German · Hebrew · Italian ·
Korean
4 PX Hardware Maintenance Manual
· Spanish
DANGER
Electrical current from power, telephone and communication cables is
hazardous.
To avoid a shock hazard:
· Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical storm.
· Connect all power cords to a properly wired and grounded electrical outlet.
· Connect to properly wired outlets any equipment that will be attached to
this product. · When possible, use one hand only to connect or disconnect
signal cables. · Never turn on any equipment when there is evidence of fire,
water, or structural damage. · Disconnect the attached power cords,
telecommunications systems, networks, and modems
before you open the device covers, unless instructed otherwise in the
installation and configuration procedures. · Connect and disconnect cables as
described in the following tables when installing, moving, or opening covers
on this product or attached devices.
To Connect
1. Turn everything OFF. 2. First, attach all cables to devices. 3. Attach
signal cables to connectors. 4. Attach power cords to outlet. 5. Turn device
ON.
To Disconnect
1. Turn everything OFF. 2. First, remove power cords from outlet. 3. Remove
signal cables from connectors. 4. Remove all cables from devices.
CAUTION: When replacing the lithium battery, use only Part Number 45C1566 or
an equivalent type battery recommended by the manufacturer. If your system has
a module containing a lithium battery, replace it only with the same module
type made by the same manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of. Do not: · Throw or
immerse into water · Heat to more than 100°C (212°F) · Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
CAUTION:
Chapter 1. Important safety information 5
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or
transmitters) are installed, note the following: · Do not remove the covers.
Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device. ·
Use of controls or adjustments or performance of procedures other than those
specified herein
might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note
the following: Laser radiation when open. Do not stare into the beam, do not
view directly with optical instruments, and avoid direct exposure to the beam.
18 kg (37 lb) CAUTION: Use safe practices when lifting.
32 kg (70.5 lb)
55 kg (121.2 lb)
CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
2 1
6 PX Hardware Maintenance Manual
Chapter 1. Important safety information 7
18 kg (37 lb)
32 kg (70.5 lb)
55 kg (121.2 lb)
2 1
8 PX Hardware Maintenance Manual
PERIGO
A corrente elétrica proveniente de cabos de alimentação, de telefone e de
comunicações é perigosa.
Para evitar risco de choque elétrico:
· Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou
reconfiguração deste produto durante uma tempestade com raios.
· Conecte todos os cabos de alimentação a tomadas elétricas corretamente
instaladas e aterradas. · Todo equipamento que for conectado a este produto
deve ser conectado a tomadas corretamente
instaladas. · Quando possível, utilize apenas uma das mãos para conectar ou
desconectar cabos de sinal. · Nunca ligue nenhum equipamento quando houver
evidência de fogo, água ou danos estruturais. · Antes de abrir tampas de
dispositivos, desconecte cabos de alimentação, sistemas de telecomunicação,
redes e modems conectados, a menos que especificado de maneira diferente nos
procedimentos de instalação e configuração. · Conecte e desconecte os cabos
conforme descrito na tabela apresentada a seguir ao instalar, mover ou abrir
tampas deste produto ou de dispositivos conectados.
Para Conectar:
1. DESLIGUE Tudo. 2. Primeiramente, conecte todos os cabos aos
dispositivos. 3. Conecte os cabos de sinal aos conectores. 4. Conecte os cabos
de alimentação às tomadas. 5. LIGUE os dispositivos.
Para Desconectar:
1. DESLIGUE Tudo. 2. Primeiramente, remova os cabos de alimentação das
tomadas. 3. Remova os cabos de sinal dos conectores. 4. Remova todos os cabos
dos dispositivos.
CUIDADO:
Ao substituir a bateria de lítio, utilize apenas uma bateria com Número de
Peça 45C1566 ou um tipo de bateria equivalente recomendado pelo Se o seu
sistema possui um módulo com uma bateria de lítio, substitua-o apenas por um
módulo do mesmo tipo e do mesmo fabricante. A bateria contém lítio e pode
explodir se não for utilizada, manuseada ou descartada de maneira correta.
Não: · Jogue ou coloque na água · Aqueça a mais de 100°C (212°F) · Conserte
nem desmonte
Descarte a bateria conforme requerido pelas leis ou regulamentos locais.
Chapter 1. Important safety information 9
PRECAUCIÓN:
Quando produtos a laser (como unidades de CD-ROMs, unidades de DVD-ROM,
dispositivos de fibra ótica ou transmissores) estiverem instalados, observe o
seguinte: · Não remova as tampas. A remoção das tampas de um produto a laser
pode resultar em exposição
prejudicial à radiação de laser. Não existem peças que podem ser consertadas
no interior do dispositivo. · A utilização de controles ou ajustes ou a
execução de procedimentos diferentes dos especificados aqui
pode resultar em exposição prejudicial à radiação.
PERIGO
Alguns produtos a laser contêm diodo de laser integrado da Classe 3A ou da
Classe 3B. Observe o seguinte:
Radiação a laser quando aberto. Não olhe diretamente para o feixe a olho nu ou
com instrumentos ópticos e evite exposição direta ao feixe.
18 kg (37 lb)
32 kg (70.5 lb) 55 kg (121.2 lb)
CUIDADO: Utilize procedimentos de segurança para levantar equipamentos.
CUIDADO: O botão de controle de alimentação do dispositivo e o botão para
ligar/desligar da fonte de alimentação não desligam a corrente elétrica
fornecida ao dispositivo. O dispositivo também pode ter mais de um cabo de
alimentação. Para remover toda a corrente elétrica do dispositivo, assegure
que todos os cabos de alimentação estejam desconectados da fonte de
alimentação.
2 1
10 PX Hardware Maintenance Manual
Chapter 1. Important safety information 11
2 1
12 PX Hardware Maintenance Manual
Chapter 1. Important safety information 13
2 1
DANGER
Le courant électrique provenant de l’alimentation, du téléphone et des câbles
de transmission peut présenter un danger.
Pour éviter tout risque de choc électrique : · Ne manipulez aucun câble et
n’effectuez aucune opération d’installation, d’entretien ou de reconfiguration
de ce produit au cours d’un orage. · Branchez tous les cordons d’alimentation
sur un socle de prise de courant correctement câblé et mis à la
terre. · Branchez sur des socles de prise de courant correctement câblés tout
équipement connecté à ce produit. · Lorsque cela est possible, n’utilisez
qu’une seule main pour connecter ou déconnecter les câbles
d’interface. · Ne mettez jamais un équipement sous tension en cas d’incendie
ou d’inondation, ou en présence de
dommages matériels. · Avant de retirer les carters de l’unité, mettez celle-ci
hors tension et déconnectez ses cordons
d’alimentation, ainsi que les câbles qui la relient aux réseaux, aux systèmes
de télécommunication et aux modems (sauf instruction contraire mentionnée dans
les procédures d’installation et de configuration). · Lorsque vous installez,
que vous déplacez, ou que vous manipulez le présent produit ou des
périphériques qui lui sont raccordés, reportez-vous aux instructions ci-
dessous pour connecter et déconnecter les différents cordons.
14 PX Hardware Maintenance Manual
Connexion
Déconnexion
1. Mettez les unités HORS TENSION.
2. Commencez par brancher tous les cordons sur les unités.
3. Branchez les câbles d’interface sur des connecteurs.
4. Branchez les cordons d’alimentation sur des prises.
5. Mettez les unités SOUS TENSION.
1. Mettez les unités HORS TENSION. 2. Débranchez les cordons d’alimentation des prises. 3. Débranchez les câbles d’interface des connecteurs. 4. Débranchez tous les câbles des unités.
ATTENTION: Remplacer la pile au lithium usagée par une pile de référence
identique exclusivement, (référence 45C1566), ou suivre les instructions du
fabricant qui en définit les équivalences. Si votre système est doté d’un
module contenant une pile au lithium, vous devez le remplacer uniquement par
un module identique, produit par le même fabricant. La pile contient du
lithium et peut exploser en cas de mauvaise utilisation, de mauvaise
manipulation ou de mise au rebut inappropriée. Ne pas : · la jeter à l’eau, ·
l’exposer à des températures supérieures à 100°C, · chercher à la réparer ou à
la démonter. Ne pas mettre la pile à la poubelle. Pour la mise au rebut, se
reporter à la réglementation en vigueur.
ATTENTION: Si des produits à laser (tels que des unités de CD-ROM, de DVD-ROM,
des unités à fibres optiques, ou des émetteurs) sont installés, prenez
connaissance des informations suivantes : · Ne retirez pas le carter. En
ouvrant l’unité de CD-ROM ou de DVD-ROM, vous vous exposez au
rayonnement dangereux du laser. Aucune pièce de l’unité n’est réparable. ·
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes
de réglage et
d’utilisation des commandes, ainsi que les procédures décrites dans le présent
manuel.
DANGER Certains produits à laser contiennent une diode à laser intégrée de
classe 3A ou 3B. Prenez connaissance des informations suivantes: Rayonnement
laser lorsque le carter est ouvert. Evitez toute expositiondirecte au rayon
laser. Evitez de regarder fixement le faisceau ou del’observer à l’aide
d’instruments optiques.
Chapter 1. Important safety information 15
18 kg (37 lb)
32 kg (70.5 lb) 55 kg (121.2 lb)
ATTENTION: Soulevez la machine avec précaution.
ATTENTION: L’interrupteur de contrôle d’alimentation de l’unité et
l’interrupteur dubloc d’alimentation ne coupent pas le courant électrique
alimentantl’unité. En outre, le système peut être équipé de plusieurs
cordonsd’alimentation. Pour mettre l’unité hors tension, vous devez
déconnectertous les cordons de la source d’alimentation.
2 1
VORSICHT
An Netz-, Telefon- und Datenleitungen können gefährliche Spannungen anliegen.
Aus Sicherheitsgründen: · Bei Gewitter an diesem Gerät keine Kabel anschließen
oder lösen. Ferner keine Installations-,
Wartungs- oder Rekonfigurationsarbeiten durchführen. · Gerät nur an eine
Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt
anschließen. · Alle angeschlossenen Geräte ebenfalls an
Schutzkontaktsteckdosen mit ordnungsgemäß
geerdetem Schutzkontakt anschließen. · Die Signalkabel nach Möglichkeit
einhändig anschließen oder lösen, um einen Stromschlag durch
Berühren von Oberflächen mit unterschiedlichem elektrischem Potenzial zu
vermeiden.
16 PX Hardware Maintenance Manual
· Geräte niemals einschalten, wenn Hinweise auf Feuer, Wasser oder
Gebäudeschäden vorliegen.
· Die Verbindung zu den angeschlossenen Netzkabeln,
Telekommunikationssystemen, Netzwerken und Modems ist vor dem Öffnen des
Gehäuses zu unterbrechen, sofern in den Installations- und
Konfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind.
· Zum Installieren, Transportieren und Öffnen der Abdeckungen des Computers
oder der angeschlossenen Einheiten die Kabel gemäß der folgenden Tabelle
anschließen und abziehen.
Zum Anschließen der Kabel gehen Sie wie folgt vor
1. Schalten Sie alle Einheiten AUS. 2. Schließen Sie erst alle Kabel an die
Einheiten an. 3. Schließen Sie die Signalkabel an die Buchsen an. 4. Schließen
Sie die Netzkabel an die Steckdose an. 5. Schalten Sie die Einheit EIN.
Zum Abziehen der Kabel gehen Sie wie folgt vor
1. Schalten Sie alle Einheiten AUS. 2. Ziehen Sie zuerst alle Netzkabel aus
den
Netzsteckdosen. 3. Ziehen Sie die Signalkabel aus den Buchsen. 4. Ziehen Sie
alle Kabel von den Einheiten ab.
CAUTION:
Eine verbrauchte Lithiumbatterie nur durch eine Batterie mit der Teilenummer
45C1566 oder eine gleichwertige, vom Hersteller empfohlene Batterie ersetzen.
Enthält das System ein Modul mit einer Lithiumbatterie, dieses nur durch ein
Modul desselben Typs und von demselben Hersteller ersetzen. Die Batterie
enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder
Entsorgung explodieren.
Die Batterie nicht: · mit Wasser in Berührung bringen. · über 100 C erhitzen.
· reparieren oder zerlegen.
Die örtlichen Bestimmungen für die Entsorgung von Sondermüll beachten.
ACHTUNG:
Bei der Installation von Lasergeräten (wie CD-ROM-Laufwerken, DVD- aufwerken,
Einheiten mit Lichtwellenleitertechnik oder Sendern) Folgendes beachten:
· Die Abdeckungen nicht entfernen. Durch Entfernen der Abdeckungen des
Lasergeräts können gefährliche Laserstrahlungen freigesetzt werden. Das Gerät
enthält keine zu wartenden Teile.
· Werden Steuerelemente, Einstellungen oder Durchführungen von Prozeduren
anders als hier angegeben verwendet, kann gefährliche Laserstrahlung
auftreten.
VORSICHT
Chapter 1. Important safety information 17
Einige Lasergeräte enthalten eine Laserdiode der Klasse 3A oder 3B. Beachten
Sie Folgendes:
Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine
Lupen oder Spiegel verwenden. Strahlungsbereich meiden.
18 kg
32 kg
55 kg
ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten.
ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die
Stromversorgung für die Einheit nicht unterbrochen. Die Einheit kann auch mit
mehreren Netzkabeln ausgestattet sein. Um die Stromversorgung für die Einheit
vollständig zu unterbrechen, müssen alle zum Gerät führenden Netzkabel vom
Netz getrennt werden.
2 1
18 PX Hardware Maintenance Manual
Chapter 1. Important safety information 19
2 1
PERICOLO La corrente elettrica proveniente dai cavi di alimentazione, del
telefono e di comunicazione può essere pericolosa.
20 PX Hardware Maintenance Manual
Per evitare il rischio di scosse elettriche:
· Non collegare o scollegare qualsiasi cavo oppure effettuare l’installazione,
la manutenzione o la riconfigurazione del prodotto durante un temporale.
· Collegare tutti i fili elettrici a una presa di alimentazione correttamente
cablata e dotata di messa a terra.
· Collegare alle prese elettriche appropriate tutte le apparecchiature che
verranno utilizzate per questo prodotto.
· Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di
segnale.
· Non accendere assolutamente apparecchiature in presenza di incendi, perdite
d’acqua o danno strutturale.
· Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti
e il modem prima di aprire i coperchi del dispositivo, salvo istruzioni
contrarie relative alle procedure di installazione e configurazione.
· Collegare e scollegare i cavi come descritto nella seguente tabella quando
vengono effettuate operazioni di installazione, spostamento o apertura dei
coperchi di questo prodotto o delle unità collegate.
Per collegarsi
1. SPEGNERE le apparecchiature. 2. Innanzitutto, collegare tutti i cavi alle
unità. 3. Collegare i cavi di segnale ai connettori. 4. Collegare i cavi di
alimentazione alla presa. 5. Accendere l’unità.
Per scollegarsi
1. SPEGNERE le apparecchiature. 2. Innanzitutto, rimuovere i cavi di
alimentazione dalla
presa. 3. Rimuovere i cavi di segnale dai connettori. 4. Rimuovere tutti i
cavi dalle unità.
ATTENZIONE:
Quando si sostituisce la batteria al litio, utilizzare solo il Numero parte
45C1566 o un tipo di batteria equivalente consigliato dal produttore. Se sul
sistema è presente un modulo che contiene una batteria al litio, sostituirlo
solo con un tipo di modulo dello stesso tipo della stessa casa di produzione.
La batteria contiene litio e può esplodere se usata, maneggiata o smaltita in
modo non corretto.
Non: · Gettare o immergere la batteria nell’acqua · Riscaldarla ad una
temperatura superiore ai 100 gradi C (212 gradi F) · Smontarla, ricaricarla o
tentare di ripararla
Le batterie usate vanno smaltite in accordo alla normativa in vigore (DPR
915/82 e successive disposizioni e disposizioni locali).
ATTENZIONE:
Chapter 1. Important safety information 21
Quando vengono installati prodotti laser (quali CD-ROM, unità DVD-ROM, unità a
fibre ottiche o trasmittenti), tener presente quanto segue: · Non rimuovere
gli sportelli. L’apertura di un’unità laser può determinare l’esposizione a
radiazioni
laser pericolose. All’interno dell’unità non vi sono parti su cui effettuare
l’assistenza tecnica. · L’utilizzo di controlli, regolazioni o l’esecuzione di
procedure non descritti nel presente manuale
possono provocare l’esposizione a radiazioni pericolose.
PERICOLO Alcune unità laser contengono un diodo laser di Classe 3A o Classe
3B. Tener presente quanto segue: Aprendo l’unità vengono emesse radiazioni
laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici
ed evitare l’esposizione al fascio.
18 kg
32 kg
ATTENZIONE: Prestare attenzione nel sollevare l’apparecchiatura.
55 kg
ATTENZIONE: Il pulsante di controllo dell’alimentazione presente sull’unità e
l’interruttore dell’alimentatore non disattivano l’alimentazione corrente
fornita all’unità. E’ possibile che l’unità disponga di più cavi di
alimentazione. Per disattivare l’alimentazione dall’unità, accertarsi che
tutti i cavi di alimentazione siano scollegati dalla fonte di alimentazione.
2 1
22 PX Hardware Maintenance Manual
Chapter 1. Important safety information 23
2 1
PELIGRO La corriente eléctrica procedente de cables de alimentación, teléfonos
y cables de comunicación puede ser peligrosa. Para evitar el riesgo de
descarga eléctrica: · No conecte ni desconecte los cables ni realice ninguna
tarea de instalación, mantenimiento o
reconfiguración de este producto durante una tormenta eléctrica. · Conecte
todos los cables de alimentación a tomas de corriente debidamente cableadas y
conectadas a tierra.
24 PX Hardware Maintenance Manual
· Cualquier equipo que se conecte a este producto también debe conectarse a
tomas de corriente debidamente cableadas.
· Siempre que sea posible, utilice una sola mano para conectar o desconectar
los cables de señal.
· No encienda nunca un equipo cuando hay señales de fuego, agua o daños
estructurales.
· Desconecte los cables de alimentación, los sistemas de telecomunicaciones,
las redes y los módems conectados antes de abrir las cubiertas de los
dispositivos, a menos que se indique lo contrario en los procedimientos de
instalación y configuración.
· Conecte y desconecte los cables, como se describe en la tabla siguiente,
cuando instale, mueva o abra las cubiertas de este producto o de los
dispositivos conectados.
Para conectar
1. APÁGUELO todo. 2. En primer lugar, conecte todos los cables a los
dispositivos. 3. Conecte los cables de señal a los conectores. 4. Enchufe los
cables de alimentación a las tomas de
corriente. 5. Encienda el dispositivo.
Para desconectar
1. APÁGUELO todo. 2. En primer lugar, desenchufe los cables de
alimentación de las tomas de corriente. 3. Desconecte los cables de señal de
los conectores. 4. Desconecte todos los cables de los dispositivos.
PRECAUCIÓN: Cuando sustituya una batería de litio, utilice solamente una
batería número de pieza 45C1566 u otra de tipo equivalente recomendada por el
fabricante. Si su sistema dispone de un módulo que contiene una batería de
litio, reemplácelo sólo con el mismo tipo de módulo, del mismo fabricante. La
batería contiene litio y puede explotar si no se utiliza, manipula o desecha
correctamente.
No debe: · Arrojarla al agua o sumergirla en ella · Exponerla a temperaturas
superiores a 100°C (212°F) · Repararla o desmontarla Deshágase de la batería
según especifiquen las leyes o normas locales.
PRECAUCIÓN: Cuando haya productos láser (como unidades de CD-ROM, unidades de
DVD, dispositivos de fibra óptica o transmisores) instalados, tenga en cuenta
lo siguiente: · No quite las cubiertas. Si quita las cubiertas del producto
láser, podría quedar expuesto a radiación
láser peligrosa. Dentro del dispositivo no existe ninguna pieza que requiera
servicio técnico. · Si usa controles o ajustes o realiza procedimientos que no
sean los especificados aquí, podría
exponerse a radiaciones peligrosas.
Chapter 1. Important safety information 25
PELIGRO
Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase
3B. Tenga en cuenta lo siguiente:
Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo
láser, ni siquiera con instrumentos ópticos, y evite exponerse directamente al
rayo láser.
18 kg
32 kg
PRECAUCIÓN: Adopte procedimientos seguros al levantar el equipo.
55 kg
PRECAUCIÓN: El botón de control de alimentación del dispositivo y el
interruptor de alimentación de la fuente de alimentación no desconectan la
corriente eléctrica suministrada al dispositivo. Además, el dispositivo podría
tener más de un cable de alimentación. Para suprimir toda la corriente
eléctrica del dispositivo, asegúrese de que todos los cables de alimentación
estén desconectados de la toma de corriente.
2 1
26 PX Hardware Maintenance Manual
Chapter 2. Important service information
Strategy for replacing FRUs
Before replacing parts: Ensure that all software fixes, drivers, and UEFI BIOS
downloads are installed before you replace any FRUs listed in this manual.
After a system board is replaced, ensure that the latest UEFI BIOS is loaded
to the system board before you complete the service action.
To download and install software fixes, drivers, and UEFI BIOS, go to
https://pcsupport.lenovo.com and follow the instructions on the screen.
Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs: · If you are instructed to replace a FRU but the replacement
does not correct the problem, reinstall the
original FRU before you continue. · Some computers have both a processor board
and a system board. If you are instructed to replace either
the processor board or the system board, and replacing one of them does not
correct the problem, reinstall that board, and then replace the other one. ·
If an adapter or a device consists of more than one FRU, any of the FRUs might
be the cause of the error. Before replacing the adapter or device, remove the
FRUs, one by one, to see if the symptoms change. Replace only the FRU that
changed the symptoms.
Strategy for replacing a hard disk drive or a solid-state drive
Always try to run a low-level format operation before replacing a hard disk
drive or a solid-state drive. This will cause all customer data on the drive
to be lost. Ensure that the customer has a current backup of the data before
you perform this task.
Attention: The drive startup sequence in the computer you are servicing might
have been changed. Be extremely careful during write operations such as
copying, saving, or formatting. If you select an incorrect drive, data or
programs can be overwritten.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling of a system board can cause damage to those components, and may cause
a system malfunction.
After replacing the system board, use the Golden Key U1 tool to bind the model
type, serial number, and Brand ID of the computer with the new system board.
Refer to https://support.lenovo.com/us/en/solutions/ ht507251 for
instructions.
Attention: When handling a system board: · Do not drop a system board or apply
any excessive force to it. · Avoid rough handling of any kind. · Avoid bending
a system board and hard pushing to prevent cracking at each Ball Grid Array
(BGA)
chipset.
© Copyright Lenovo 2023
27
How to use error codes
Use the error codes displayed on the screen to diagnose failures. If more than
one error code is displayed, begin the diagnosis with the first error code.
Whatever causes the first error code might also cause false error codes. If no
error code is displayed, see whether the error symptom is listed in the
“Symptom-to-FRU Index” section.
Strategy for replacing FRUs for CTO, special-bid, and standard models
This topic provides information about the model types and FRU identification.
Product definition
This topic introduces different model types and how to identify each type.
Dynamic Configure To Order (CTO) model This model provides the ability for a
customer to configure a Lenovo solution from a Web site, and have this
configuration sent to fulfillment, where it is built and shipped directly to
the customer. The machine label and eSupport will load these products as the
4-character MT, 4-character model, and 2-character country code. The model is
“CTO1” and the default country code is “WW” (example: 20AACTO1WW). Special-bid
model This model is a unique configuration that has been negotiated between
Lenovo and the customer. A unique MTM consists of a 4-character MT, a
4-character model, and a numeric 2-character country code is provided to the
customer to place orders (example: 20AA000955). The country code assigned is
numeric and does not designate a specific country or region. The custom model
factsheet for the MTM indicates which country the special-bid MTM is set up
for. Special-bid offering is not generally announced. Standard model Standard
models (fixed configuration) are announced and offered to all customers. The
MTM portion of the machine label consists of a 4-character MT, a 4-character
model, and an alphabetic 2-character country code. The country code assigned
is alphabetic and represents a designated country or region (example:
20AA0009UK).
FRU identification
To identify FRUs for a product, do the following: 1. Go to:
https://support.lenovo.com/partslookup. 2. Type the Machine Type in the
corresponding field to get a general FRU list, or type the Serial Number for
more detailed FRU information.
28 PX Hardware Maintenance Manual
Chapter 3. Product overview
Notices for side ventilation and workplace power
Side ventilation notice Side ventilation design is available on some models.
Pay attention to the ventilation distance requirements for models with
different configurations: · Systems configured with rear-exhausting graphics
cards (such as NVIDIA RTX 6000 Ada) do not require
side ventilation. · Systems configured with internal-exhausting graphics cards
(such as GeForce RTX 4070 and GeForce
RTX 4080) require side ventilation. Do not block air vents on the left side
cover. To ensure heat dissipation, do not place any objects within 4.5 cm (1.8
inches) or 1 rack unit from the left side cover. · For rack-mounted systems, a
rack spacer is recommended in the gap above the system.
Note: Do not install internal-exhausting graphics cards (such as GeForce RTX
4070 and GeForce RTX 4080) on systems without side ventilation on the left
side cover.
Workplace power and system configuration requirements
· Only use the power cord shipped with your computer. · General power supply
requirements:
Ensure that your workplace is able to support the AC outlet and AC current
requirements. Low AC voltage countries require up to 20 amps of AC power.
Japan and Taiwan region require a high AC voltage outlet. See details in the
table below for North America, Japan, and Taiwan region.
© Copyright Lenovo 2023
29
Low / High AC voltage Countries or regions
Low AC voltage
North America (110-127V AC typical)
Requirements
Require 110-127V / 20A AC receptacle.
Lenovo power cord part number: SL60P41047
Low AC voltage
Japan (100V AC typical)
125V / 20A
Require 200V / 12A AC receptacle. Lenovo power cord part number:
SL60P41056
Low AC voltage
Taiwan region (110V AC typical)
250V / 15A
Require 220V / 12A AC receptacle. Lenovo power cord part number:
SL60P41049
250V / 15A
High AC voltage
Countries or regions except North America, Japan, and Taiwan region
Require 220-240V / 12A AC various receptacle.
Minimum 12A circuit per power supply
· Redundant mode hot-plug power supply requirements:
A dedicated circuit is recommended for each power supply to maximize
redundancy.
System must be configured to the maximum output of single power supply.
Upgrading system components may compromise redundancy.
· Teamed mode power supply requirements:
A dedicated circuit is required for each power supply for low AC voltage
workplace and is recommended for high AC voltage workplace.
Teaming allows system power output up to 2350 W. Total output power is
100-240V / 27-12A AC.
Do not hot plug in teamed mode with system power consumption above single
PSU maximum output power. This might result in immediate power off.
30 PX Hardware Maintenance Manual
Front
Item 1. 3. 5. 7. 9. 11. 13.
Description Power button USB-A 3.2 Gen 2 connector USB-C® (3.2 Gen 2) connectors Diagnostic LCD switch ThinkStation®LED Front access bays (1 to 6) M.2 solid-state drive LED labels*
Item 2. 4. 6. 8. 10. 12. 14.
Description Power indicator Always On USB-A 3.2 Gen 2 connector Headset connector Diagnostic LCD Front access bay lock Hard disk drive LED label Dual M.2 SSD enclosure locks*
- for selected models
Statement on USB transfer rate
Depending on many factors such as the processing capability of the host and peripheral devices, file attributes, and other factors related to system configuration and operating environments, the actual transfer rate using the various USB connectors on this device will vary and will be slower than the data rate listed below for each corresponding device.
USB device 3.2 Gen 1 3.2 Gen 2 3.2 Gen 2 × 2
Data rate (Gbit/s) 5 10 20
Chapter 3. Product overview 31
USB device Thunderbolt 3 (USB-C) Thunderbolt 4 (USB-C)
Data rate (Gbit/s) 40 40
Power indicator Show the system status of your computer. · On: The computer is
starting up or working. · Off: The computer is off or in hibernation mode. ·
Blinking slowly: The computer is in sleep mode.
Always On USB-A 3.2 Gen 2 connector With the Always On USB feature enabled,
the Always On USB-A 3.2 Gen 2 connector can charge a USB-A compatible device
when the computer is on, off, in sleep mode, or in hibernation mode.
To enable the Always On USB feature, do the following: 1. Enter the UEFI BIOS
menu. 2. Click Devices USB Setup Front USB Ports USB Port 2 to enable the
Always On USB feature.
Diagnostic LCD switch Use the diagnostic LCD switch to turn on or turn off the
diagnostic LCD, and handle occurred events.
Status No event
Error events occur
Behavior and function
Short press: Turn on or turn off the diagnostic LCD. Date and time will be
displayed on the LCD when it is turned on. The LCD will turn off automatically
if idle for three minutes.
The diagnostic LCD will turn on automatically when an error event occurs.
· Short press (when multiple events occur): Switch among error events and
display the corresponding QR code of the selected event.
· Long press (about 3 seconds): Clear the selected event.
Diagnostic LCD Display the diagnostic information when an issue or error is
detected. You can decode the error code at
https://www.thinkworkstationsoftware.com/codes.
Hard disk drive or M.2 solid-state drive LED label The storage drives have the
following two types of LEDs:
32 PX Hardware Maintenance Manual
LED Status LED Activity LED
Status and indication
· Solid on: The storage drive status is failure. · 4 Hz blinking (four times
per second): Locating the storage drive. · 1 Hz blinking (once a second):
Rebuilding RAID. · Off (when the computer is powered on): The storage drive
status is normal.
· Solid on: The storage drive is online, installed, or powered on (no
activity). · Variable blinking: Accessing the storage drive. · Off (when the
computer is powered on): The storage drive is not installed or
powered.
Chapter 3. Product overview 33
Rear
Item 1.
3.
5. 7. 9. 11. 13. 15.
Description Power supply unit bays (2)
PCI-Express card areas
Key-nest for the dual M.2 SSD enclosure Power indicator Audio line-out
connector USB-A 3.2 Gen 1 connectors Ethernet connector (1 G) Ethernet
connector (10 G)
Item 2.
4.
6. 8. 10. 12. 14. 16.
Description
Power cord connector Key-nest for the left side cover and front access bays
Power button Audio line-in connector USB-C (3.2 Gen 2×2) connector Serial
connector* USB-A 2.0 connectors Security-lock slot
- for selected models
Power indicator Show the system status of your computer. · On: The computer is starting up or working. · Off: The computer is off or in hibernation mode. · Blinking slowly: The computer is in sleep mode.
Serial connector Connect an external modem, a serial printer, or other devices that use a serial connector.
34 PX Hardware Maintenance Manual
PCI-Express card areas Install PCI-Express cards into these areas to improve
the operating performance of the computer. Depending on the computer model,
the video output connectors in these areas might be DisplayPortTM connectors
or Mini DisplayPortTM connectors.
Chapter 3. Product overview 35
36 PX Hardware Maintenance Manual
Chapter 4. Service checkout and symptom-to-FRU index
This chapter provides information about general service checkout and symptom-
to-FRU index.
Service checkout
Attention: The drives in the computer you are servicing might have been
rearranged or the drive startup sequence changed. Be extremely careful during
write operations such as copying, saving, or formatting. Data or programs can
be overwritten if you select an incorrect drive.
General error messages appear if a problem or conflict is found by a program,
the operating system, or both. For an explanation of these messages, refer to
the information supplied with that software package.
Use the following procedure to help determine the cause of the problem: 1.
Turn off the computer and all external devices. 2. Check all cables and power
cords. 3. Set all display controls to the middle position. 4. Turn on all
external devices. 5. Turn on the computer. · Look for displayed error codes. ·
Listen for beep codes. · Look for readable instructions or a main menu on the
display. If you did not receive the correct response, proceed to step 6 on
page 37. If you do receive the correct response, proceed to step 7 on page 37.
6. Look at the following conditions and follow the instructions: · If you hear
beep codes during POST, go to “Beep symptoms” on page 39. · If the computer
displays a POST error, go to “POST error codes” on page 40. · If the computer
hangs and no error is displayed, continue at step 7 on page 37. 7. Run the
Diagnostic programs. See Chapter 6 “Diagnostics” on page 51. · If you receive
an error, replace the part that the diagnostic program calls out. · If the
test stops and you cannot continue, replace the last device tested.
Problem determination tips
Due to the variety of hardware and software combinations that can be
encountered, use the following information to assist you in problem
determination. If possible, have this information available when requesting
assistance from Service Support and Engineering functions. · Machine type and
model · Processor or hard disk drive upgrades · Failure symptom
Do diagnostics indicate a failure? What, when, where, single, or multiple
systems? Is the failure repeatable? Has this configuration ever worked?
© Copyright Lenovo 2023
37
If it has been working, what changes were made prior to its failing? Is
this the original reported failure? · Diagnostics version Type and version
level · Hardware configuration Print (print screen) configuration currently
in use BIOS level · Operating system software Type and version level
Notes: To eliminate confusion, identical systems are considered identical only
if they: 1. Are the exact machine type and models 2. Have the same BIOS level
3. Have the same adapters/attachments in the same locations 4. Have the same
address jumpers/terminators/cabling 5. Have the same software versions and
levels 6. Have the same Diagnostic Diskettes (version) 7. Have the same
configuration options set in the system 8. Have the same setup for the
operating system control files
Comparing the configuration and software set-up between “working and non-
working” systems will often lead to problem resolution.
Symptom-to-FRU index
The Symptom-to-FRU index lists error symptoms and possible causes. The most
likely cause is listed first. Always begin with “Service checkout” on page 37.
This index can also be used to help you decide which FRUs to have available
when servicing a computer. If you are unable to correct the problem using this
index, go to “Undetermined problems” on page 43.
Notes:
· The Symptom-to-FRU index is not specific to any machine type and are
applicable to all computers. · If you have both an error message and an
incorrect audio response, diagnose the error message first. · If you cannot
run the diagnostic tests or you get a diagnostic error code when running a
test, but did
receive a POST error message, diagnose the POST error message first. · If you
did not receive any error message, look for a description of your error
symptoms in the first part of
this index.
Hard disk drive boot error
A hard disk drive boot error can have the following causes.
Error
The start-up drive is not in the boot sequence in configuration.
No operating system installed on the boot drive.
FRU/Action
Check the configuration and ensure that the start-up drive is in the boot
sequence.
Install an operating system on the boot drive.
38 PX Hardware Maintenance Manual
Error The boot sector on the startup drive is corrupted.
The drive is defective.
FRU/Action
The drive must be formatted. Do the following: 1. Attempt to back up the data
on the failing hard disk drive. 2. Using the operating system programs, format
the hard disk drive.
Replace the hard disk drive.
Power supply problems
If you suspect a power problem, use the following procedures.
Check/Verify
Check the following for proper installation. · Power cord · On/Off switch
connector · On/Off switch power supply connector · System board power supply
connectors · Microprocessor connection
Check the power cord for continuity.
Check the power-on switch for continuity.
FRU/Action Reseat connectors
Power cord Power-on switch
Beep symptoms
Beep symptoms are tones or a series of tones separated by pauses (intervals
without sound) during POST.
The following table describes the beep symptoms.
Beep symptom 2 short beeps: common POST error 3 short and 1 long beeps: DRAM
memory error
4 long beeps: insufficient shadow RAM resources for option ROM (error code:
8998) or PCIe/PCI MMIO (memory mapped input/output) resources (error code:
8999) 2 long and 3 short beeps: graphics card error
FRU/Action Common POST error code. See the detailed failure information in
“POST error codes” on page 40.
Perform the following actions in order: 1. Make sure that the memory modules
are properly seated in the memory slots. 2. Replace the memory modules. 3.
Replace the system board (for trained service personnel only).
See the detailed failure information in “POST error codes” on page 40.
Perform the following actions in order: 1. Make sure that the graphics cards
are properly seated in the slots. 2. Replace the graphics cards. 3. Replace
the system board (for trained service personnel only).
Chapter 4. Service checkout and symptom-to-FRU index 39
POST error codes
Each time you turn on the system, it performs a series of tests that check the
operation of the system and some options. This series of tests are called the
Power-On Self-Test, or POST. POST checks the following operations:
· Some basic system-board operations · Memory operation · Video operation ·
Whether the boot drive is working
If the POST detects a problem, an error message appears on the screen. A
single problem might cause several error messages to appear. When you correct
the cause of the first error message, the other error messages probably will
not appear on the screen the next time.
Error code 0135
0162
0164 1762
POST error message CPU fan failure System fan failure Power fan failure Front
fan failure Rear fan failure Auxiliary fan failure ODD fan failure Setup data
integrity check failure
Memory configuration change has occurred
Storage device configuration change has occurred
Description/Action
This error message is displayed when a fan fails and the system might be
overheating. Press F10 to exit.
This error indicates the checksum of BIOS Setup data in NVRAM is bad. In BIOS
Setup, the “Save Changes and Exit” operation is needed in order to clear this
error.
This error message is displayed when the memory size is changed. Press F10 to
exit.
This error message is displayed when a hard disk drive change or an optical
drive change has been made. Press F10 to exit.
40 PX Hardware Maintenance Manual
Error code 8998
8999
POST error message Not enough shadow RAM resources for OPTION ROM, not all
devices initialized. Suggest to remove some add-on cards, or change to UEFI
mode in BIOS setup.
Not enough PCIe/PCI MMIO resources. Currently only one video card is enabled.
Remove some PCIe cards.
Description/Action
This error message is displayed when the shadow RAM resources for option ROM
are insufficient.
If the legacy option ROM is insufficient, remove some add-in cards.
For the system that supports UEFI, set UEFI as the first priority.
This error message is displayed when the PCIe/PCI MMIO (memory mapped
input/output) resources are insufficient.
Remove some add-in cards.
Miscellaneous error conditions
Message/Symptom Changing display colors
FRU/Action Display/Monitor
Computer will not power-off. See “Hard disk drive boot error” on page 38.
Computer will not RPL from server
1. Power Switch 2. System Board 3. Riser card, if installed.
1. Ensure that the network is in startup sequence as the first device or the
first device after diskette.
2. Ensure that the network adapter is enabled for RPL. 3. Network adapter
(Advise network administrator of
new MAC address)
Computer will not perform a Wake On LAN® (if applicable)
1. Check the power supply and signal cable connections to the network
adapter.
2. Ensure that the operating system settings are set to enable Wake on LAN.
3. Ensure that the Wake On LAN feature is enabled in Setup/Configuration.
4. Ensure that the network administrator is using the correct MAC address.
5. Ensure no interrupt or I/O address conflicts.
6. Network adapter (advise network administrator of new MAC address)
Dead computer. See “Hard disk drive boot error” on page 38.
1. Power Supply 2. System Board
Diskette drive in-use light remains on or does not light when drive is active.
1. Diskette Drive 2. System Board 3. Diskette Drive Cable
Chapter 4. Service checkout and symptom-to-FRU index 41
Message/Symptom
FRU/Action
Blank screen except for flashing cursor.
1. System Board 2. Primary Hard Disk Drive 3. Hard Disk Drive Cable
Incorrect memory size during POST
1. Run the Memory tests. 2. Memory Module 3. System Board
“Insert a Diskette” icon appears with a known-good diagnostics diskette in the first 3.5-inch diskette drive.
1. System Board 2. Diskette Drive Cable 3. Network Adapter
Intensity or color varies from left to right of characters and color bars
1. Display 2. Video adapter (if present) 3. System Board
No power or fan not running
1. See “Hard disk drive boot error” on page 38.
Non-system disk or disk error-type message with a known-good diagnostic diskette.
1. Diskette Drive 2. System Board 3. Diskette Drive Cable
Other display symptoms not listed above (including blank or illegible display)
1. Display 2. System Board
Power-on indicator or hard disk drive in-use light not on, but computer works correctly
1. Power switch/LED assembly 2. System Board
Printer problems
1. Printer 2. System Board
Program loads from the hard disk with a known-good diagnostics diskette in the first 3.5-inch diskette drive
1. Run the Setup Utility program and check the Startup sequence.
2. Diskette Drive 3. Diskette Drive Cable 4. System Board 5. Power Supply
RPL computer cannot access programs from its own hard disk.
1. If the network administrator is using LCCM Hybrid RPL, check the startup
sequence:
a. First device – network
b. Second device – hard disk
2. Hard disk drive
RPL computer does not RPL from server
1. Check the startup sequence. 2. Check the network adapter LED status.
42 PX Hardware Maintenance Manual
Message/Symptom Serial or parallel connector device failure (system board
connector)
Serial or parallel connector device failure (adapter connector)
Some or all keys on the keyboard do not work
FRU/Action
1. External Device Self-Test OK? 2. External Device 3. Cable 4. System Board
1. External Device Self-Test OK? 2. External Device 3. Cable 4. Alternate
Adapter 5. System Board
1. Keyboard 2. Keyboard Cable 3. System Board
Undetermined problems
This section provides instructions on how to find out the failing devices or
adapters. 1. Turn off the computer. 2. Remove or disconnect the following
components (if installed) one at a time. a. External devices (modem, printer,
or mouse) b. Any adapters c. Memory modules d. Extended video memory e.
External Cache f. External Cache RAM g. Hard disk drive h. Diskette drive 3.
Turn on the computer to retest the system. 4. Repeat steps 1 through 3 until
you find the failing device or adapter.
If all devices and adapters have been removed, and the problem continues,
replace the system board. See Chapter 7 “Hardware removal and installation” on
page 55.
Recover from a BIOS update failure
1. Remove all media from the drives and turn off all connected devices. 2.
Insert the BIOS update disc into the optical drive, and then turn off the
computer. 3. Disconnect all power cords from electrical outlets. Then, remove
any parts that impede access to the
Clear CMOS jumper. 4. Move the jumper from the standard position to the
maintenance position. 5. Reconnect the power cords for the computer and the
monitor to electrical outlets. 6. Turn on the computer and the monitor. When
the computer beeps, the recovery process begins. 7. After the recovery process
is completed, the computer will be turned off automatically.
Chapter 4. Service checkout and symptom-to-FRU index 43
Note: Depending on the computer model, the recovery process will take two to
three minutes. 8. Disconnect all power cords from electrical outlets. 9. Move
the jumper back to the standard position. 10. Reinstall all the parts that
have been removed. Then, reconnect the power cords for the computer and
the monitor to electrical outlets. 11. Turn on the computer and the monitor.
When the logo screen is displayed, press F1 or Fn+F1. 12. To prevent data
loss, ensure that BIOS settings are restored to an earlier point.
Clear CMOS
1. Remove all media from the drives and turn off all connected devices and
the computer. 2. Disconnect all power cords from electrical outlets. Then,
remove any parts that impede access to the
Clear CMOS jumper. 3. Move the jumper from the standard position to the
maintenance position. 4. Reconnect the power cords for the computer and the
monitor to electrical outlets. 5. Turn on the computer and the monitor. When
the computer beeps, wait for approximately 10 seconds. 6. Turn off the
computer by holding the power button for approximately four seconds. 7.
Disconnect all power cords from electrical outlets. 8. Move the jumper back to
the standard position. 9. Reinstall all the parts that have been removed.
Then, reconnect the power cords for the computer and
the monitor to electrical outlets. 10. Turn on the computer and the monitor.
When the logo screen is displayed, press F1 or Fn+F1. 11. To prevent data
loss, ensure that BIOS settings are restored to an earlier point.
44 PX Hardware Maintenance Manual
Chapter 5. RAID
What is RAID
Redundant Array of Independent Disks (RAID) is a technology that provides
increased storage functions and reliability through redundancy. It also can
improve data storage reliability and fault tolerance compared with single-
drive storage systems. Data loss resulting from a drive failure can be
prevented by reconstructing missing data from the remaining drives.
When a group of independent physical storage drives is set up to use RAID
technology, they are in a RAID array. This array distributes data across
multiple storage drives, but the array appears to the host computer as one
single storage unit. Creating and using RAID arrays provides high performance,
such as the expedited I/O performance, because several drives can be accessed
simultaneously.
Configure RAID with Intel RSTe
If your computer comes with the Intel RSTe configuration utility, you can
follow the sections below to configure RAID with Intel RSTe.
Storage drive requirements for RAID levels Your computer supports the
following RAID levels: · RAID 0: striped disk array
Consists of at least two SATA storage drives Supported strip size: 4 KB, 8
KB, 16 KB, 32 KB, 64 KB, or 128 KB Better performance without fault
tolerance · RAID 1: mirrored disk array Consists of two SATA storage drives
Improved reading performance and 100% redundancy · RAID 10: striped and
mirrored disk array (a combination of RAID 0 and RAID 1) Consists of four
SATA storage drives Supported strip size: 4 KB, 8 KB, 16 KB, 32 KB, or 64 KB
· RAID 5: block-level striped disk array with distributed parity Consists of
at least three SATA storage drives Supported strip size: 16 KB, 32 KB, 64
KB, or 128 KB Better performance and fault tolerance
Create a RAID volume Attention: All the existing data stored on the selected
drives will be erased while the RAID volume is being created.
To create a RAID volume: 1. Enable RAID by doing the following: a. Restart the
computer. When the logo screen is displayed, press F1 or Fn+F1. b. Select
Devices PCH SATA Configuration and press Enter.
© Copyright Lenovo 2023
45
c. Select Configure SATA as and press Enter. Then, select RAID and press
Enter. d. Press F10 or Fn+F10 to save the changes and exit. 2. Enter the BIOS
menu again. 3. Select Advanced Intel RSTe SATA Controller and press Enter. 4.
Select Create RAID Volume and press Enter. The Create RAID Volume window is
displayed. 5. Select and configure the options one by one. a. Name: You can
use the default name Volume0 or type a preferred name for the RAID volume. b.
RAID Level: You can set the RAID level to one of the following:
· RAID0 · RAID1 · RAID10 · RAID5
Note: Some of the RAID levels might not be displayed because the number of
installed SATA storage drives varies. c. Select Disks: Select a storage drive
and press Enter. Then, select X and press Enter to add it to a group. d. Strip
Size (if applicable): Select a strip size and press Enter. e. Capacity:
Customize the capacity of the RAID volume. The default RAID volume is the
largest value. 6. Select Create Volume and press Enter to create a RAID
volume. 7. Exit the BIOS menu.
View the information about a RAID volume To view the information about a RAID
volume:
1. Restart the computer. When the logo screen is displayed, press F1 or
Fn+F1. 2. Select Advanced Intel RSTe SATA Controller and press Enter. 3.
Select RAID Volumes and press Enter. 4. Select a RAID volume and press Enter
to view the detailed information. 5. Press F10 or Fn+F10 to save the changes
and exit.
Delete a RAID volume Attention: All the existing data stored on the selected
drives will be erased after you delete RAID volumes.
To delete a RAID volume: 1. Restart the computer. When the logo screen is
displayed, press F1 or Fn+F1. 2. Select Advanced Intel RSTe SATA Controller
and press Enter. 3. Under RAID Volumes, select the RAID volume that you want
to delete and press Enter. The RAID VOLUME INFO window is displayed. 4. Select
Delete under Volume Actions and press Enter. When prompted, select Yes and
press Enter to confirm the deletion of the selected RAID volume. 5. Press F10
or Fn+F10 to save the changes and exit.
Configure RAID with AVAGO MegaRAID Configuration Utility
To configure RAID with AVAGO MegaRAID Configuration Utility, ensure that:
46 PX Hardware Maintenance Manual
· An AVAGO MegaRAID adapter is installed in your computer. · The storage
drives used for RAID configuration are connected to the installed AVAGO
MegaRAID adapter
instead of the system board.
Storage drive requirements for RAID levels Your computer supports the
following RAID levels: · RAID 0: striped disk array
Consists of at least two NVMe storage drives Supported strip size: 64 KB,
128 KB, 256 KB, 512 KB, or 1 MB Better performance without fault tolerance ·
RAID 1: mirrored disk array Consists of two or four NVMe storage drives
Improved read performance and 100% redundancy · RAID 10: striped and mirrored
disk array (a combination of RAID 0 and RAID 1) Consists of four NVMe
storage drives Data being striped across storage drive groups Provides
both high data transfer rates and complete data redundancy · RAID 5: block-
level striped disk array with distributed parity Consists of at least three
NVMe storage drives Supported strip size: 64 KB, 128 KB, 256 KB, 512 KB, or
1 MB Better performance and fault tolerance Available only on selected
models of AVAGO MegaRAID adapters · RAID 6: block-level striped disk array
with dual distributed parity Consists of at least four NVMe storage drives
Supported strip size: 64 KB, 128 KB, 256 KB, 512 KB, or 1 MB Better
performance and fault tolerance that can stand up to loss of two storage
drives Available only on selected models of AVAGO MegaRAID adapters
Create a RAID volume Attention: All the existing data stored on the selected
drives will be erased while the RAID volume is being created.
To create a RAID volume: 1. Restart the computer. When the logo screen is
displayed, press F1 or Fn+F1. 2. Select Advanced AVAGO MegaRAID Configuration
Utility and press Enter. 3. Select Main Menu and press Enter. 4. Select
Configuration Management and press Enter. 5. Select Create Virtual Drive and
press Enter. 6. Select and configure the options one by one. a. Select RAID
Level: You can set the RAID level to one of the following: · RAID0 · RAID1
Chapter 5. RAID 47
· RAID5 · RAID6 · RAID10
Note: Some of the RAID levels might not be displayed because the number of
installed storage drives and the model of the AVAGO MegaRAID adapter vary. b.
Select Drives From: Select Unconfigured capacity or Free capacity depending on
your needs and press Enter. c. Select Drives: Select a storage drive and press
Enter. After selecting all storage drives for creating the RAID volume, select
Apply Changes and press Enter. When promoted, select Confirm and press Enter.
Then, select Yes and press Enter to save the storage drive selection. Finally,
select OK and press Enter. d. Virtual Drive Name: You can type a preferred
name for the volume name. e. Strip Size (if applicable): Select a strip size
and press Enter. 7. Select Save Configuration and press Enter. When promoted,
select Confirm and press Enter. Then, select Yes and press Enter to confirm
the creation of the RAID volume. 8. Press F10 or Fn+F10 to save the changes
and exit.
View the information about a RAID volume To view the information about a RAID
volume:
1. Restart the computer. When the logo screen is displayed, press F1 or
Fn+F1. 2. Select Advanced AVAGO MegaRAID Configuration Utility and press
Enter. 3. Select Main Menu and press Enter. 4. Select Virtual Drive Management
and press Enter. 5. Select a RAID volume and press Enter to view the detailed
information. 6. Press F10 or Fn+F10 to save the changes and exit.
Delete a RAID volume Attention: All the existing data stored on the selected
drives will be erased after you delete RAID volumes.
To delete a RAID volume: 1. Restart the computer. When the logo screen is
displayed, press F1 or Fn+F1. 2. Select Advanced AVAGO MegaRAID Configuration
Utility. 3. Select Main Menu and press Enter. 4. Select Virtual Drive
Management and press Enter. 5. Select the RAID volume that is not needed and
press Enter. 6. Under Operation, select Delete Virtual Drive and press Enter.
7. Select Go and press Enter. When prompted, select Confirm and press Enter.
Then, select Yes and press Enter to delete the RAID volume. 8. Press F10 or
Fn+F10 to save the changes and exit.
Configure RAID with Intel Virtual RAID on CPU
To configure RAID with the Intel Virtual RAID on CPU configuration utility,
ensure that: · An upgrade key module is connected to the Virtual RAID on CPU
(VROC) connector on the system board.
48 PX Hardware Maintenance Manual
· M.2 solid-state drives are installed in your computer.
Storage drive requirements for RAID levels Your computer supports the
following RAID levels: · RAID 0: striped disk array
Consists of at least two M.2 solid-state drives Supported strip size: 4
KB, 8 KB, 16 KB, 32 KB, 64 KB, or 128 KB Better performance without fault
tolerance · RAID 1: mirrored disk array Consists of two M.2 solid-state
drives Improved reading performance and 100% redundancy · RAID 10: striped
and mirrored disk array (a combination of RAID 0 and RAID 1) Consists of
four M.2 solid-state drives Supported strip size: 4 KB, 8 KB, 16 KB, 32 KB,
or 64 KB · RAID 5: block-level striped disk array with distributed parity
Consists of at least three M.2 solid-state drives Supported strip size: 16
KB, 32 KB, 64 KB, or 128 KB Better performance and fault tolerance
Available only on selected models of upgrade key modules
Create a RAID volume Attention: All the existing data stored on the selected
drives will be erased while the RAID volume is being created.
To create a RAID volume: 1. Enable VMD for the selected M.2 solid-state drives
by doing the following: a. Restart the computer. When the logo screen is
displayed, press F1 or Fn+F1. b. Select Advanced Intel(R) VMD technology and
press Enter. c. Select each menu item and press Enter. Then, select Enabled
and press Enter. d. Select an occupied M.2 solid-state drive slot as you need
and press Enter. Then, select VMD and press Enter. e. Press F10 or Fn+F10 to
save the changes and exit. 2. Enter the BIOS menu again. 3. Select Advanced
Intel Virtual RAID on CPU and press Enter. 4. Select All Intel VMD Controllers
and press Enter. 5. Select Create Volumes and press Enter. 6. Select and
configure the options one by one. a. Name: You can use the default name
Volume0 or type a preferred name for the RAID volume. b. RAID Level: You can
set the RAID level to one of the following: · RAID0 · RAID1 · RAID10
Chapter 5. RAID 49
· RAID5 Note: Some of the RAID levels might not be displayed because the
number of installed M.2 solidstate drives and the model of the upgrade key
module vary. c. Select Disks: Select an M.2 solid-state drive and press Enter.
Then, select X and press Enter to add it to a group. d. Stripe Size (if
applicable): Select a stripe size and press Enter. e. Capacity: Customize the
capacity of the RAID volume. The default RAID volume is the largest value. 7.
Select Create Volume and press Enter to create a RAID volume. 8. Exit the BIOS
menu. View the information about a RAID volume To view the information about a
RAID volume: 1. Restart the computer. When the logo screen is displayed, press
F1 or Fn+F1. 2. Select Advanced Intel Virtual RAID on CPU and press Enter. 3.
Select RAID Volumes and press Enter. 4. Select a RAID volume and press Enter
to view the detailed information. 5. Press F10 or Fn+F10 to save the changes
and exit. Delete a RAID volume Attention: All the existing data stored on the
selected drives will be erased after you delete RAID volumes. To delete a RAID
volume: 1. Restart the computer. When the logo screen is displayed, press F1
or Fn+F1. 2. Select Advanced Intel Virtual RAID on CPU and press Enter. 3.
Select Intel VROC Mananged Volumes and press Enter. 4. Under Volume Actions,
select Delete and press Enter. 5. When prompted, select Yes and press Enter to
confirm the deletion of the selected RAID volume. 6. Press F10 or Fn+F10 to
save the changes and exit.
50 PX Hardware Maintenance Manual
Chapter 6. Diagnostics
Use diagnostic solutions to test hardware components and report operating-
system-controlled settings that interfere with the correct operation of your
computer.
Basic procedure for resolving computer problems
Prerequisite Before you start, read Chapter 1 “Important safety information”
on page 1 and print the following instructions.
1. Check that: a. The cables for all connected devices are connected
correctly and securely. b. All components have been reassembled correctly. c.
All connected devices that require ac power are connected to properly grounded
and working electrical outlets. d. All connected devices are enabled in UEFI
BIOS.
2. Use an antivirus program to see if the computer has been infected by a
virus. If the program detects a virus, remove the virus.
3. Go to “Self-help resources” on page 53 and follow the instructions for the
type of problem you are experiencing.
4. Run the diagnostic program. 5. Recover your operating system. See “Self-
help resources” on page 53. 6. If the problem persists, contact Lenovo.
UEFI diagnostic program
A UEFI diagnostic program is preinstalled on the computer. It enables you to
test memory modules and internal storage devices, view system information, and
check and recover bad sectors on internal storage devices.
To run the UEFI diagnostic program, do the following: 1. Turn on the computer.
If the computer cannot be turned on, go to “Basic procedure for resolving
computer problems” on page 51. If an error code is displayed, go to “Symptom-
to-FRU index” on page 38 for error code descriptions and troubleshooting
hints. 2. Repeatedly press and release the F10 key when turning on the
computer. The main screen of the UEFI diagnostic program is displayed. 3.
Follow the instructions on the screen to use the diagnostic program.
The options on the main screen are as follows:
© Copyright Lenovo 2023
51
Table 1. Options on the main screen of the UEFI diagnostic program
DIAGNOSTICS
TOOLS
· CPU [U] · DISPLAY [D] · MEMORY [E] · MOTHERBOARD [H] · PCI EXPRESS [P] · STORAGE [S] · AUDIO [Z] · OPTICAL [O] · RUN ALL [R]
· SYSTEM INFORMATION [F1] · BAD BLOCK RECOVERY [F3] · SMART INFORMATION [F5]
Note: The options on the main screen might vary, depending on the hardware configuration and the UEFI diagnostic program version preinstalled on the computer.
Diagnostics
Use diagnostic solutions to test hardware components and report operating-
system-controlled settings that interfere with the correct operation of your
computer.
When an error message pops up in the Windows notification area, a four-digit
error code is displayed on the diagnostic LCD (for selected models) on the
front panel, or the diagnostic indicator on the front panel turns on, do one
of the following:
· If ThinkStation Diagnostics can be launched properly: 1. Click the error
message or the ThinkStation Diagnostics icon to launch the program. 2. All
events are logged locally in the program. Locate the related event and view
the event log to find possible solutions. 3. Record the four-digit error code
displayed on the diagnostic LCD (for selected models) or in ThinkStation
Diagnostics, and then decode the error at
https://www.thinkworkstationsoftware.com/ codes.
Note: You can download ThinkStation Diagnostics at
https://pcsupport.lenovo.com/ lenovodiagnosticsolutions/downloads. · If your
computer does not function:
1. Use your smartphone to scan the QR code displayed on the diagnostic LCD to
open https:// www.thinkworkstationsoftware.com/codes.
2. Decode the error according to the four-digit error code displayed on the
diagnostic LCD.
For more information, go to https://www.thinkworkstationsoftware.com/diags.
The Vantage app The Vantage app is preinstalled on your computer. To diagnose
problems with the Vantage app:
1. Type Vantage in the Windows search box and press Enter. 2. Follow the on-
screen instructions and run a hardware scan.
52 PX Hardware Maintenance Manual
If you are unable to isolate and resolve the problem after running the Vantage app, save and print the log files created by the program. You might need the log files when you speak to a Lenovo technical support representative.
Self-help resources
Use the following self-help resources to learn more about the computer and
troubleshoot problems.
Resources Troubleshooting and frequently asked questions Accessibility information
How to access?
· https://www.lenovo.com/tips · https://forums.lenovo.com
https://www.lenovo.com/accessibility
Reset or restore Windows
Use the Vantage app to: · Configure device settings. · Download and install
UEFI BIOS, drivers and firmware
updates. · Secure you computer from outside threats. · Diagnose hardware
problems. · Check the computer warranty status. · Access User Guide and
helpful articles. Note: The available features vary depending on the computer
model. Product documentation: · Safety and Warranty Guide · Generic Safety and
Compliance Notices · Setup Guide · This User Guide · Regulatory Notice
· Use Lenovo recovery options. 1. Go to https://support.lenovo.com/
HowToCreateLenovoRecovery. 2. Follow the on-screen instructions.
· Use Windows recovery options. 1. Go to https://pcsupport.lenovo.com. 2.
Detect your computer or manually select your computer model. 3. Navigate to
the troubleshooting menu to diagnose the operating system for recovery
instructions.
Type Vantage in the Windows search box.
Go to https://pcsupport.lenovo.com. Then, follow the onscreen instructions to
filter out the documentation you want.
Chapter 6. Diagnostics 53
Resources Lenovo Support Web site with the latest support information of the
following: · Drivers and software · Diagnostic solutions · Product and service
warranty · Product and parts details · Knowledge base and frequently asked
questions
Windows help information
How to access?
https://pcsupport.lenovo.com
· Type Get Help or Tips in the Windows search box. · Use Windows Search or the
Cortana® personal
assistant. · Microsoft support Web site:
https://support.microsoft.com
54 PX Hardware Maintenance Manual
Chapter 7. Hardware removal and installation
This chapter provides instructions on how to remove and install hardware for your computer.
Handling static-sensitive devices
Do not open the static-protective package containing the new part until the
defective part has been removed and you are ready to install the new part.
Static electricity, although harmless to you, can seriously damage computer
components and options.
When you handle options and other computer components, take these precautions
to avoid static-electricity damage:
· Limit your movement. Movement can cause static electricity to build up
around you.
· Always handle options and other computer components carefully. Handle
PCI/PCIe cards, memory modules, system boards, and microprocessors by the
edges. Never touch any exposed circuitry.
· Prevent others from touching the options and other computer components.
· Touch the static-protective package containing the part to a metal
expansion-slot cover or other unpainted metal surface on the computer for at
least two seconds. This reduces static electricity from the package and your
body before you install or replace a new part.
· When possible, remove the new part from the static-protective package, and
install it directly in the computer without setting the part down. When this
is not possible, place the static-protective package on a smooth, level
surface and place the part on the package.
· Do not place the part on the computer cover or other metal surface.
Service tool kit
Ensure that the following common service tool kit is prepared before you
service the computer.
No.
Tool name
Specific
Product scope
Tool type
1
Screw driver: Philips Head 0
PH0
All
Common tool
2
Screw driver: Philips Head 00
PH00
All
Common tool
3
Screw driver: Philips Head 01
1
All
Common tool
4
Screw driver: Philips Head 01
1, Shank length greater than 6
ThinkSation/DT
Common tool
inches
5
Screw driver: Philips Head 02
2, Shank length greater than 6 ThinkSation/SC/DT Common tool
inches
6
Screw driver: Torx Head T5
T5
IdeaPad
Common tool
© Copyright Lenovo 2023
55
No.
Tool name
Specific
Product scope
Tool type
7
Screw driver: Torx Head T15
T15, for Chassis outside
ThinkSation
Common tool
8
Screw driver: Torx Head T20
T20, Shank length greater than
ThinkSation
6 inches, for heatsink and CPU
9
Screw driver: Torx Head T30
T30, Shank length greater than
ThinkSation
6 inches, for heatsink and CPU
10
Pry tools 1
N/A
All
Common tool Common tool Common tool
11
Tweezers (conductive)
N/A
All
Common tool
12
Tweezers (isolated)
N/A
All
Common tool
13
Suction cup
N/A
All
Common tool
14
Hexagonal socket (for VGA )
H5 mm or 4.8 mm
ThinkCentre/Tiny
Common tool
15
Hexagonal socket (for
Tiny antenna)
16 Silicone grease for CPU or heatsink repairing
17
Polyamide tape
H8 mm N/A N/A
ThinkCentre/Tiny
Common tool
All
Consumable
All
Consumable
18
Mylar tape
N/A
All
Consumable
19
Eraser
N/A
All
Consumable
20
Electrical tape
N/A
All
Consumable
21
Double sided tape
N/A
All
Consumable
22
Conductive tape
N/A
All
Consumable
23
Cleaning pads/wipes
N/A
All
Consumable
56 PX Hardware Maintenance Manual
No.
Tool name
24
Heat gun
25
Brown brush
Specific N/A
25 mm to 35 mm wide
Product scope
Tool type
All
Special tool
All
Special tool
Note: The silicone grease can be applied to the surfaces of the microprocessor
and heat sink to eliminate air gaps. For parts with silicone grease applied,
it is suggested that you apply new grease during the installation.
Major FRUs and CRUs
Your computer contains the following types of CRUs and FRUs:
· Self-service CRUs: Refer to parts that can be replaced easily by customer
themselves or by trained service technicians at an additional cost.
· Optional-service CRUs: Refer to parts that can be replaced by customers with
a greater skill level. Trained service technicians can also provide service to
replace the parts under the type of warranty designated for the customer’s
machine.
· FRUs: Refer to parts that must be replaced only by trained service
technicians. If customers choose to replace the FRUs by themselves, the
product warranty might be affected.
Chapter 7. Hardware removal and installation 57
58 PX Hardware Maintenance Manual
Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
Description Right side cover Power distribution board and bracket Storage fan assembly BCB board and bracket Wi-Fi antenna cover NVLINK bridge ThinkStation logo badge ID badge Front panel IO assembly Memory module Hard disk drive bracket Hard disk drive Lock kit for the front access bay Think LED holder Think LED cable Dual M.2 SSD enclosure Blank bezel M.2 solid-state drive On board M.2 solid-state drive heatsink kit CPU carrier CPU heatsink CPU Misc cables Keyboard Mouse Power cord NVLINK retainer Cover presence switches (left and right) Left side cover Thermal sensor Front Wi-Fi antenna Rear Wi-Fi / BT antenna assembly Wi-Fi card adapter Wi-Fi card Wi-Fi card cover System board
Self-service CRU Yes No Yes No Yes No Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No Yes Yes Yes Yes No Yes No No No No No No No
Optional-service CRU No Yes No Yes No Yes No No Yes No No No No No No No No No No No No No No No No No No No No No No No No No No No
Chapter 7. Hardware removal and installation 59
Number 37 38 39 40 41 42 43 44 45 46 47 48 49
50 51 52 53 54
Description Front fan bracket Lock kit for the left side cover Memory fan Front fan assembly Speaker CPU duct Rear fan assembly PCIe bracket Customized PCIe extender Chassis PCIe card Super capacitor module Fiber modules of NVIDIA ConnectX-6 Ethernet Adapter card Rear power button Power supply assembly PSU bay storage enclosure Dummy cover for the upper PSU bay Top cover
Self-service CRU Yes Yes Yes Yes No Yes Yes Yes Yes No Yes Yes Yes
Optional-service CRU No No No No No No No No No No No No No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
For detailed FRU and CRU information, such as the FRU part numbers and supported computer models, go to: http://www.lenovo.com/serviceparts-lookup
System board
Note: The system board might look slightly different from the illustration.
60 PX Hardware Maintenance Manual
Figure 1. System board (front) part locations Chapter 7. Hardware removal and installation 61
Figure 2. System board (back) part locations
Item 1 PCIe card slot 9 (x 16, Gen4, Microprocessor 1) 3 PCIe card slot 7 (x
16, Gen4, Microprocessor 1) 5 Memory slot 9 7 Memory slot 11 9 Serial port
(COM) connector 11 Microprocessor 2* 13 PCIe card slot 5 (x 8, Gen4,
Microprocessor 2) 15 PCIe card slot 3 (x 16, Gen5, Microprocessor 2) 17
Internal-speaker connector 19 Memory slot 16 21 Memory slot 14 23 Memory slot
1 25 Memory slot 3 27 Coin-cell battery 29 M.2 solid-state drive slot 2 31
Right cover presence switch connector (intrusion switch connector)
Item 2 PCIe card slot 8 (x 16, Gen5, Microprocessor 1) 4 PCIe card slot 6 (x 16, Gen5, Microprocessor 1) 6 Memory slot 10 8 Memory slot 12 10 Rear-fan- assembly connector 12 Top memory-fan connector 14 PCIe card slot 4 (x 16, Gen5, Microprocessor 2) 16 PCIe card slot 2 (x 16, Gen4, Microprocessor 2) 18 PCIe card slot 1 (x 16, Gen4, Microprocessor 2) 20 Memory slot 15 22 Memory slot 13 24 Memory slot 2 26 Memory slot 4 28 M.2 solid-state drive slot 3 30 M.2 solid-state drive slot 1 32 Graphics card power connector 4
62 PX Hardware Maintenance Manual
Item 33 Graphics card power connector 3 35 Front panel connector 37 Front fan assembly connector 1 39 Thermal sensor connector 41 Bottom memory-fan connector 43 Graphics card power connector 2 45 Left cover presence switch connector (intrusion switch connector) 47 Power button header 49 Thunderbolt control connector 51 Memory slot 5 53 Memory slot 7 55 Alternative Trusted Platform Module (TPM) header 57 USB 2.0 59 VROC 61 Clear CMOS jumper 63 MCIO connector 2 65 Power distribution board connector
Item 34 Front fan assembly connector 2 36 Microprocessor 1 38 Misc power
connector 40 Logo LED connector 42 Graphics card power connector 1 44 Front
fan assembly connector 3 46 Microprocessor 1 fan connector
48 ThunderboltTM power connector 50 USB 3.2 Gen1 52 Memory slot 6 54 Drive_ACT
56 Memory slot 8 58 BMC 60 Reset header 62 Microprocessor 2 fan connector 64
MCIO connector 1 66 Drive_backplane
Chapter 7. Hardware removal and installation 63
Expand your computer
You can enhance your computer capacity and performance by adding various
devices according to the following rules:
Note: To add or replace a device, see “Removing and installing hardware” on
page 64.
Item 1. Memory slots 2. On-board M.2 solid-state drive slots
3. Front access bays (1 to 6)
Description Up to sixteen memory modules are installed in selected models.
Up to three M.2 solid-state drives are installed in selected models.
You can install the following storage drives in front access bays: · Up to
three 3.5inch hard disk drives (hot-swappable) · Up to four M.2 solid-state
drive (hot-swappable)
3a. Front access bay 1 to 3 3b. Front access bay 2+5 and 3 +6 4. PCIe slots
5. Power supply unit bay 2
Note: The dual M.2 SSD enclosure priority is higher than the 3.5-inch hard
disk drive.
You can install up to three 3.5inch hard disk drives (hot-swappable) in
selected models.
You can install up to two dual M.2 SSD enclosures in selected models. Each
dual M.2 SSD enclosure supports up to two M.2 solid-state drives* (hot-
swappable).
You can install compatible PCIe cards (up to nine) in the PCIe card slots.
You can install a power supply assembly or a PSU bay storage enclosure with a
3.5-inch hard disk drive in this bay.
Note: The PSU bay storage enclosure priority is higher than the power supply
assembly.
- for selected models
Removing and installing hardware
This section provides instructions on how to remove and install hardware for
your computer. Attention: Do not open your computer or attempt any repair
before reading and understanding the Chapter 1 “Important safety information”
on page 1.
64 PX Hardware Maintenance Manual
External options
You can connect external options to your computer, such as external speakers,
a printer, or a scanner. For some external options, you must install
additional software in addition to making the physical connection. When
installing an external option, see Chapter 3 “Product overview” on page 29 to
identify the required connector. Then, use the instructions that come with the
option to help you make the connection and install any required software or
device drivers.
ThinkStation logo badge
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. Removal steps Remove the ThinkStation logo
badge.
ID badge
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. Removal steps Remove the ID badge.
Chapter 7. Hardware removal and installation 65
Dummy cover for the upper PSU bay
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. Removal steps Remove the dummy cover for the
upper PSU bay.
66 PX Hardware Maintenance Manual
Power supply assembly
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. The power supply assembly is hot-swappable.
Removal steps Remove the power supply assembly.
Chapter 7. Hardware removal and installation 67
Top cover
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
Before you open the computer cover, turn off the computer and wait several
minutes until the computer is cool. For access, do the following:
1. Remove any media from the drives and turn off all connected devices and
the computer. 2. Disconnect all power cords from electrical outlets and
disconnect all cables from the computer. Removal steps Remove the top cover.
68 PX Hardware Maintenance Manual
Front and rear Wi-Fi antenna
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, remove the top cover. See “Top
cover” on page 68. For access, do the following:
1. Rremove the top cover. See “Top cover” on page 68. 2. Remove the left side
cover. See “Left side cover” on page 72. 3. Remove the CPU duct. See “CPU
duct” on page 75. Removal steps Remove the front and rear Wi-Fi antenna.
Chapter 7. Hardware removal and installation 69
Screw (quantity) M2 x 3 mm, Zn coated (1)
Color Black
Torque 1.5 ± 0.2 lb/in
70 PX Hardware Maintenance Manual
Note: When installing the front and rear Wi-Fi antenna, follow the following cable routing: Chapter 7. Hardware removal and installation 71
Wi-Fi antenna cover
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, remove the top cover. See “Top
cover” on page 68. Removal steps Remove the Wi-Fi antenna cover.
Left side cover
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
Before you open the computer cover, turn off the computer and wait several
minutes until the computer is cool. For access, do the following:
1. Remove any media from the drives and turn off all connected devices and
the computer. 2. Disconnect all power cords from electrical outlets and
disconnect all cables from the computer. 3. Unlock any locking device that
secures the computer cover. 4. Lay the computer on its side for easier access
to the left side cover.
72 PX Hardware Maintenance Manual
Removal steps Remove the left side cover.
Installation steps Install the left side cover.
Chapter 7. Hardware removal and installation 73
Note: If a locking device is available, use it to lock the computer after
installing the computer cover.
NVLINK retainer
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, remove the left side cover. See
“Left side cover” on page 72.
74 PX Hardware Maintenance Manual
Removal steps Remove the NVLINK retainer.
CPU duct
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, remove the left side cover. See
“Left side cover” on page 72. Removal steps Remove the CPU duct.
Wi-Fi card adapter
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
Chapter 7. Hardware removal and installation 75
For access, do the following: 1. Remove the left side cover. See “Left side
cover” on page 72. 2. Remove the CPU duct. See “CPU duct” on page 75.
Removal steps Remove the Wi-Fi card adapter.
Note: If your computer comes with a Wi-Fi card that supports the Bluetooth
function, disconnect the Bluetooth cable from the Wi-Fi card adapter.
Screw (quantity) M2 x 3 mm, Zn coated (1)
Color Black
Torque 1.5 ± 0.2 lb/in
76 PX Hardware Maintenance Manual
Note: When installing the Wi-Fi card adapter, follow the following cable
routing to connect the Bluetooth cable to the USB 2.0 connector on the system
board. See “System board” on page 60.
Chapter 7. Hardware removal and installation 77
Wi-Fi card
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. Removal steps Remove the Wi-Fi card.
78 PX Hardware Maintenance Manual
Screw (quantity) M2 x 3 mm, Zn coated (1)
Color Black
Torque 1.5 ± 0.2 lb/in
Front fan assembly
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
For access, remove the left side cover. See “Left side cover” on page 72.
Removal steps Remove the front fan assembly.
Chapter 7. Hardware removal and installation 79
NVLINK bridge
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. Note: The NVLINK bridge is shipped in an
accessary box within the computer carton box. You need to take it out from the
packaging and install it by yourself. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. Installation steps Install the NVLINK
bridge.
80 PX Hardware Maintenance Manual
Removal steps Remove the NVLINK bridge.
Front fan bracket
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
Chapter 7. Hardware removal and installation 81
For access, do the following: 1. Remove the left side cover. See “Left side
cover” on page 72. 2. Remove the CPU duct. See “CPU duct” on page 75. 3.
Remove the front fan assembly. See “Front fan assembly” on page 79.
Removal steps Remove the front fan bracket.
82 PX Hardware Maintenance Manual
Thermal sensor
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the front fan assembly. See
“Front fan assembly” on page 79. 4. Remove the front fan bracket. See “Front
fan bracket” on page 81. Removal steps Remove the thermal sensor.
Rear fan assembly
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. Removal steps Remove the rear fan
assembly.
Chapter 7. Hardware removal and installation 83
Blank bezel
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, remove the hard disk drive
bracket beside the blank bezel. See “Hard disk drive in the front access bay”
on page 92. Removal steps Remove the blank bezel.
84 PX Hardware Maintenance Manual
Front panel IO assembly
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the front fan assembly. See
“Front fan assembly” on page 79. 4. Remove the front fan bracket. See “Front
fan bracket” on page 81. Removal steps Remove the front panel IO assembly.
Chapter 7. Hardware removal and installation 85
Lock kit for the front access bay
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the front fan assembly. See
“Front fan assembly” on page 79. 4. Remove the front fan bracket. See “Front
fan bracket” on page 81. Removal steps Remove the front access bay lock.
86 PX Hardware Maintenance Manual
Installation steps Install the front access bay lock.
Chapter 7. Hardware removal and installation 87
Think LED holder and cable
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the front fan assembly. See
“Front fan assembly” on page 79. 4. Remove the front fan bracket. See “Front
fan bracket” on page 81. Removal steps Remove the Think LED holder and cable.
88 PX Hardware Maintenance Manual
Lock kit for the left side cover
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, remove the left side cover. See
“Left side cover” on page 72.
Chapter 7. Hardware removal and installation 89
Removal steps Remove the left side cover lock.
Note: Loosen the two screws that secure the lock handle cover. The two screws
cannot be removed from the lock handle cover.
Screw (quantity) 6-32*3.8 mm, Zn coated (2)
Color Blue
Torque 3.0 ± 0.5 lb/in
Screw (quantity) M3 x 4.2 mm, Zn coated (1)
Color Blue
Torque 5.0 ± 0.5 lb/in
90 PX Hardware Maintenance Manual
Installation steps Install the left side cover lock.
Chapter 7. Hardware removal and installation 91
Hard disk drive in the front access bay
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
Attention: The internal storage drive is sensitive. Inappropriate handling
might cause damage and permanent loss of data. When handling the internal
storage drive, observe the following guidelines: · Replace the internal
storage drive only for repair. The internal storage drive is not designed for
frequent
changes or replacement. · Before replacing the internal storage drive, make a
backup copy of all the data that you want to keep. · Do not touch the contact
edge of the internal storage drive. Otherwise, the internal storage drive
might get
damaged. · Do not apply pressure to the internal storage drive. · Do not make
the internal storage drive subject to physical shocks or vibration. Put the
internal storage
drive on a soft material, such as cloth, to absorb physical shocks.
You can install or replace a storage drive in the front access bay. The
storage drive also can be hotswappable, which means that you can install or
replace the drive without even turning off your computer. Therefore, lock the
storage drive to prevent the unexpected removal. The keys are attached at the
rear of the computer. Store the keys in a secure place.
92 PX Hardware Maintenance Manual
Attention: The storage drive in the front access bay is hot-swappable only
when the operating system of your computer does not reside on the storage
drive installed in the front access bay. If the requirement is not met, do not
remove or install the storage drive when the computer is turned on. Otherwise,
data on the storage drive might get damaged. Removal steps of hard disk drive
installed in the front access bay You might need to use the key attached at
the rear of the computer to unlock the front access bay and then remove the
hard disk drive.
Chapter 7. Hardware removal and installation 93
Installation steps of hard disk drive installed in the front access bay
Install the hard disk drive.
94 PX Hardware Maintenance Manual
Hard disk drive in the PSU bay storage enclosure
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
Attention: The internal storage drive is sensitive. Inappropriate handling
might cause damage and permanent loss of data. When handling the internal
storage drive, observe the following guidelines: · Replace the internal
storage drive only for repair. The internal storage drive is not designed for
frequent
changes or replacement. · Before replacing the internal storage drive, make a
backup copy of all the data that you want to keep. · Do not touch the contact
edge of the internal storage drive. Otherwise, the internal storage drive
might get
damaged. · Do not apply pressure to the internal storage drive. · Do not make
the internal storage drive subject to physical shocks or vibration. Put the
internal storage
drive on a soft material, such as cloth, to absorb physical shocks.
For access, do the following: 1. Remove the left side cover. See “Left side
cover” on page 72. 2. Remove the right side cover. See “Right side cover” on
page 97.
Removal steps Remove the hard disk drive in the PSU bay storage enclosure.
Screw (quantity) M3 x 5 mm, Nickel coated (1)
Color Black
Torque 5.0 ± 0.5 lb/in
Chapter 7. Hardware removal and installation 95
96 PX Hardware Maintenance Manual
Right side cover
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, remove the left side cover. See
“Left side cover” on page 72. Removal steps Remove the right side cover.
Chapter 7. Hardware removal and installation 97
Installation steps Install the right side cover.
98 PX Hardware Maintenance Manual
Cover presence switches
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. Removal steps of the right cover presence
switch For access, do the following:
Chapter 7. Hardware removal and installation 99
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the front fan assembly. See
“Front fan assembly” on page 79. 4. Remove the front fan bracket. See “Front
fan bracket” on page 81. Note: Disconnect the right cover presence switch
cable from the right cover presence switch connector on the system board. See
“System board” on page 60.
Removal steps of the left cover presence switch For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the front fan assembly. See
“Front fan assembly” on page 79. 4. Remove the front fan bracket. See “Front
fan bracket” on page 81. 5. Remove the right side cover. See “Right side
cover” on page 97. Note: Disconnect the left cover presence switch cable from
the left cover presence switch connector on the system board. See “System
board” on page 60.
100 PX Hardware Maintenance Manual
Power distribution board and bracket
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the power supply assembly. See “Power supply assembly” on page 67.
2. Remove the left side cover. See “Left side cover” on page 72. 3. Remove the
right side cover. See “Right side cover” on page 97. 4. Remove the PSU bay
storage enclosure. See “Hard disk drive in the PSU bay storage enclosure” on
page 95. Removal steps Loosen the three screws to remove the power
distribution board and bracket. Note: The three screws cannot be removed from
the power distribution board bracket.
Chapter 7. Hardware removal and installation 101
Screw (quantity) 6-32*3.8 mm, Zn coated (3)
Color Blue
Torque 3.0 ± 0.5 lb/in
BCB board and bracket
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
For access, do the following: 1. Remove the storage drives installed in the
front access bay (if any). See “Hard disk drive in the front access bay” on
page 92 and “M.2 solid-state drive in the front access bay” on page 104. 2.
Remove the left side cover. See “Left side cover” on page 72. 3. Remove the
right side cover. See “Right side cover” on page 97. 4. Remove the storage
drive fan. See “Storage fan assembly” on page 103.
Removal steps Loosen the three screws to remove the BCB board and bracket.
Note: The three screws cannot be removed from the BCB board bracket.
102 PX Hardware Maintenance Manual
Screw (quantity) 6-32*3.8 mm, Zn coated (3)
Color Blue
Torque 3.0 ± 0.5 lb/in
Storage fan assembly
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
For access, do the following: 1. Remove the left side cover. See “Left side
cover” on page 72. 2. Remove the right side cover. See “Right side cover” on
page 97. 3. Disconnect the storage fan cable from the system board. See
“System board” on page 60.
Removal steps Remove the storage fan assembly.
Chapter 7. Hardware removal and installation 103
M.2 solid-state drive in the front access bay
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
Attention: The internal storage drive is sensitive. Inappropriate handling
might cause damage and permanent loss of data. When handling the internal
storage drive, observe the following guidelines: · Replace the internal
storage drive only for repair. The internal storage drive is not designed for
frequent
changes or replacement. · Before replacing the internal storage drive, make a
backup copy of all the data that you want to keep. · Do not touch the contact
edge of the internal storage drive. Otherwise, the internal storage drive
might get
damaged. · Do not apply pressure to the internal storage drive. · Do not make
the internal storage drive subject to physical shocks or vibration. Put the
internal storage
drive on a soft material, such as cloth, to absorb physical shocks.
You can install or replace a storage drive in the front access bay. The
storage drive also can be hotswappable, which means that you can install or
replace the drive without even turning off your computer. Therefore, lock the
storage drive to prevent the unexpected removal. The keys are attached at the
rear of the computer. Store the keys in a secure place.
Attention: The storage drive in the front access bay is hot-swappable only
when the operating system of your computer does not reside on the storage
drive installed in the front access bay. If the requirement is not met, do not
remove or install the storage drive when the computer is turned on. Otherwise,
data on the storage drive might get damaged.
Removal steps Remove the M.2 solid-state drive.
104 PX Hardware Maintenance Manual
Chapter 7. Hardware removal and installation 105
Screw (quantity) M2 x 4.5 mm, Zn coated (4)
Color Black
Torque 1.5 ± 0.2 lb/in
Screw (quantity) M2 x 4.5 mm, Zn coated (1)
Color Black
Torque 1.5 ± 0.2 lb/in
Dual M.2 SSD enclosure
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
For access, do the following: 1. Remove the M.2 solid-state drive installed in
the front access bay (if any). See “M.2 solid-state drive in the front access
bay” on page 104. 2. Remove the left side cover. See “Left side cover” on page
72. 3. Remove the right side cover. See “Right side cover” on page 97. 4.
Remove the storage fan assembly. See “Storage fan assembly” on page 103. 5.
Disconnect the cable from the dual M.2 SSD enclosure. See “System board” on
page 60.
106 PX Hardware Maintenance Manual
Removal steps Remove the dual M.2 SSD enclosure.
Onboard M.2 solid-state drive and its heatsink kit
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. Attention: The internal storage drive is
sensitive. Inappropriate handling might cause damage and permanent loss of
data. When handling the internal storage drive, observe the following
guidelines: · Replace the internal storage drive only for repair. The internal
storage drive is not designed for frequent
changes or replacement. · Before replacing the internal storage drive, make a
backup copy of all the data that you want to keep. · Do not touch the contact
edge of the internal storage drive. Otherwise, the internal storage drive
might get
damaged. · Do not apply pressure to the internal storage drive. · Do not make
the internal storage drive subject to physical shocks or vibration. Put the
internal storage
drive on a soft material, such as cloth, to absorb physical shocks. For
access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the front fan assembly. See
“Front fan assembly” on page 79. 4. Remove the front fan bracket. See “Front
fan bracket” on page 81. Removal steps Remove the onboard M.2 solid-state
drive.
Chapter 7. Hardware removal and installation 107
Installation steps Install the onboard M.2 solid-state drive. Notes: · Remove
the protective film from both heatsink and thermal pad before installing the
onboard M.2 solid-
state drive. · If the new M.2 solid-state drive is double-sided, remove the
1.5-mm thick thermal pad upward first.
108 PX Hardware Maintenance Manual
Memory fan
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, remove the following parts in
order:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the front fan assembly. See
“Front fan assembly” on page 79. 4. Remove the front fan bracket. See “Front
fan bracket” on page 81.
Chapter 7. Hardware removal and installation 109
5. Remove the rear fan assembly. See “Rear fan assembly” on page 83. 6.
Disconnect the memory fan cable from the system board. See “System board” on
page 60. Replacement steps Remove the memory fan.
Memory module
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. Make sure to remove or install memory module
at least one minute after disconnecting power cords from the system. It allows
the system to be completely discharged of electricity and safe for handling
memory module. Ensure that you follow the installation order for memory
modules shown in the following illustration. · 1 CPU
110 PX Hardware Maintenance Manual
· 2 CPUs Chapter 7. Hardware removal and installation 111
For access, remove the following parts in order: · Remove the left side cover.
See “Left side cover” on page 72. · Remove the CPU duct. See “CPU duct” on
page 75. · Remove the front fan assembly. See “Front fan assembly” on page 79.
· Remove the front fan bracket. See “Front fan bracket” on page 81. · Remove
the rear fan assembly. See “Rear fan assembly” on page 83. · Remove the memory
fan duct. See “Memory fan” on page 109. Removal steps Remove the memory
module.
112 PX Hardware Maintenance Manual
Installation steps Install the memory module.
PCIe bracket
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. Removal steps Remove the PCIe
bracket.
Chapter 7. Hardware removal and installation 113
PCIe card
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. Install PCIe cards according to the
corresponding slot types and the following illustrated installation order: · 1
CPU
114 PX Hardware Maintenance Manual
· 2 CPUs
For access, do the following: 1. Remove the left side cover. See “Left side
cover” on page 72. 2. Remove the CPU duct. See “CPU duct” on page 75. 3.
Remove the power cable from the PCIe card, if any.
Removal steps Remove the PCIe card. Note: The PCIe card retainer is only
available on some graphics cards.
Chapter 7. Hardware removal and installation 115
Note: The card might fit tightly into the slot. If necessary, alternately move
each side of the card a small amount until the card is removed from the slot.
116 PX Hardware Maintenance Manual
Note: For NVIDIA ConnectX-6 Ethernet Adapter card, the following fiber modules
can be removed.
For cable connection guide, see “Cable connection” on page 132.
Full-length PCIe card
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. Install PCIe cards according to the
corresponding slot types and the following illustrated installation order: · 1
CPU
Chapter 7. Hardware removal and installation 117
· 2 CPUs
Note: Do not change the graphics card slot installation location if you
replace a Geforce RTX 40X0 graphics card. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the power cable from the
PCIe card, if any. Removal steps Remove the full-length PCIe card.
118 PX Hardware Maintenance Manual
Note: The card might fit tightly into the slot. If necessary, alternately move
each side of the card a small amount until the card is removed from the slot.
Notes: · For computer models with GFX RTX 4000 Ada, the graphics card and the
PCIe card extender work as a
CRU assembly. Do not try to remove the extender. · For computer models with
double-width or wider graphics cards (such as NVIDIA RTX 6000 Ada and
GeForce RTX 4080), the PCIe card extender is a customized CRU part. You can
remove it according to the following illustration. · If you want to install a
double-width or wider graphics card, install the customized PCIe card extender
first.
Chapter 7. Hardware removal and installation 119
Screw (quantity) M3 x 5.5 mm, Nickel coated (2)
Color Black
Torque 5.5 ± 0.5 lb/in
For cable connection guide, see “Cable connection” on page 132.
M.2 solid-state drive on an M.2 solid-state drive PCIe adapter
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
Attention: The internal storage drive is sensitive. Inappropriate handling
might cause damage and permanent loss of data. When handling the internal
storage drive, observe the following guidelines:
· Replace the internal storage drive only for repair. The internal storage
drive is not designed for frequent changes or replacement.
· Before replacing the internal storage drive, make a backup copy of all the
data that you want to keep. · Do not touch the contact edge of the internal
storage drive. Otherwise, the internal storage drive might get
damaged. · Do not apply pressure to the internal storage drive. · Do not make
the internal storage drive subject to physical shocks or vibration. Put the
internal storage
drive on a soft material, such as cloth, to absorb physical shocks.
Install M.2 solid-state drives in the following order as shown:
120 PX Hardware Maintenance Manual
For access, do the following: 1. Remove the left side cover. See “Left side
cover” on page 72. 2. Remove the CPU duct. See “CPU duct” on page 75. 3.
Remove the M.2 solid-state drive PCIe adapter from the PCIe card slot. See
“Full-length PCIe card” on page 117.
Replacement steps Replace the M.2 solid-state drive on the M.2 solid-state
drive PCIe adapter.
Chapter 7. Hardware removal and installation 121
If necessary, move the retention latch to an appropriate location to suit the
length of the new M.2 solid-state drive.
122 PX Hardware Maintenance Manual
Chapter 7. Hardware removal and installation 123
Note: Install the M.2 solid-state drive PCIe adapter in a PCIe x16 card slot
on the system board. See “System board” on page 60.
Super capacitor module
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. Removal steps Remove the super
capacitor module.
124 PX Hardware Maintenance Manual
Note: When installing a new super capacitor module, connect the super
capacitor module cable to the super capacitor module connector (J14) on the
RAID card.
CPU heatsink
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. CAUTION:
Avoid contact with hot components inside the computer. During operation, some
components become hot enough to burn the skin. Before you open the computer
cover, turn off the computer, disconnect power, and wait approximately 10
minutes for the components to cool. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the CPU duct. See “CPU duct” on page 75. 3. Remove the front fan assembly. See
“Front fan assembly” on page 79. 4. Remove the front fan bracket. See “Front
fan bracket” on page 81. 5. Remove the memory fan. See “Memory fan” on page
109. 6. Remove the memory modules. See “Memory module” on page 110. 7.
Disconnect the CPU heatsink cable from the microprocessor fan connector on the
system board. See
“System board” on page 60.. Removal steps
1. Remove the memory fan duct.
Chapter 7. Hardware removal and installation 125
Screw (quantity) M3 x 5 mm, Nickel coated (4)
Color Black
Torque 5.0 ± 0.5 lb/in
2. Loosen the four screws that secure the CPU heatsink to the system board in
diagonal sequence and unlock the anti-tilt wires in the same sequence to lift
the CPU heatsink. For example,
a. Partially remove screw 1a , then fully remove screw 1b , and then fully
remove screw 1a .
b. Partially remove screw 1c , then fully remove screw 1d , and then fully
remove screw 1c .
Notes:
· Use T30 screw bit with torque 10 ± 1 in-lb to loosen the four screws of CPU
heatsink. · The four screws cannot be removed from the CPU heatsink. · Place
the CPU heatsink on its side. Ensure that the thermal grease on the bottom of
it does not get in
contact with anything.
126 PX Hardware Maintenance Manual
Screw (quantity) Peek (4)
CPU and its carrier
Color Off white
Torque 10 ± 1 lb/in
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
CAUTION:
Avoid contact with hot components inside the computer. During operation, some
components become hot enough to burn the skin. Before you open the computer
cover, turn off the computer, disconnect power, and wait approximately 10
minutes for the components to cool.
Notes: · Ensure that you install the correct type of CPU option your computer
supports. · Your CPU and CPU carrier might look slightly different from the
illustrations in this topic.
For access, do the following: 1. Remove the left side cover. See “Left side
cover” on page 72. 2. Remove the CPU duct. See “CPU duct” on page 75. 3.
Remove the front fan assembly. See “Front fan assembly” on page 79. 4. Remove
the front fan bracket. See “Front fan bracket” on page 81. 5. Remove the
memory fan duct. See “Memory fan” on page 109. 6. Remove the memory modules.
See “Memory module” on page 110. 7. Remove the CPU heatsink. See “CPU
heatsink” on page 125.
Chapter 7. Hardware removal and installation 127
Removal steps Note: Touch only the edges of the CPU. Do not touch the gold
contacts on the bottom.
Install steps Notes: · Before you attach the CPU to the computer, clean all
thermal grease that has been used and then apply
new thermal grease. Apply new thermal grease at an amount of 2.5 grams, on the
parts marked a as shown in the following illustrations. Either too much or too
less application of grease can cause a thermal problem due to imperfect
contact with a component.
128 PX Hardware Maintenance Manual
Figure 3. Illustrations of the thermal grease area · Touch only the edges of
the CPU. Do not touch the gold contacts on the bottom.
Chapter 7. Hardware removal and installation 129
System board
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
CAUTION:
Avoid contact with hot components inside the computer. During operation, some
components become hot enough to burn the skin. Before you open the computer
cover, turn off the computer, disconnect power, and wait approximately 10
minutes for the components to cool.
For access, do the following: 1. Remove the power supply assembly. See “Power
supply assembly” on page 67. 2. Remove the left side cover. See “Left side
cover” on page 72. 3. Lay the computer on its side for easier access to the
system board. 4. Remove the following parts if any: · Remove the CPU duct. See
“CPU duct” on page 75. · Remove the front fan assembly. See “Front fan
assembly” on page 79. · Remove the front fan bracket. See “Front fan bracket”
on page 81. · Remove the rear fan. See “Rear fan assembly” on page 83. ·
Remove the front panel IO assembly. See “Front panel IO assembly” on page 85.
· Remove the memory fan duct. See “Memory fan” on page 109. · Remove the
memory modules. See “Memory module” on page 110. · Remove the onboard M.2
solid-state drive and its heatsink kit. See “Onboard M.2 solid-state drive and
its heatsink kit” on page 107. · Remove the M.2 solid-state drive in the front
access bay. See “M.2 solid-state drive in the front access bay” on page 104. ·
Remove the hard disk drive in the front access bay. See “Hard disk drive in
the front access bay” on page 92. · Remove the hard disk drive in the PSU bay
storage enclosure. See “Hard disk drive in the PSU bay storage enclosure” on
page 95. · Remove the Wi-Fi card adapter. See “Wi-Fi card adapter” on page 75.
· Remove the PCIe card. See “PCIe card” on page 114. · Remove the NVLINK
bridge. See “NVLINK bridge” on page 80. · Remove the super capacitor module.
See “Super capacitor module” on page 124. · Remove the Full-length PCIe card.
See “Full-length PCIe card” on page 117. · Remove the right side cover. See
“Right side cover” on page 97. · Remove the Power distribution board and
bracket. See “Power distribution board and bracket” on page 101. · Remove the
BCB board and bracket. See “BCB board and bracket” on page 102. · Remove the
storage fan assembly. See “Storage fan assembly” on page 103. · Remove the CPU
heatsink. See “CPU heatsink” on page 125. 5. Record the cable routing and
cable connections and then disconnect all cables from the system board. See
“System board” on page 60..
130 PX Hardware Maintenance Manual
Removal steps Remove the 12 screws that secure the system board shown in the following illustration.
Screw (quantity) M3 x 5 mm, Nickel coated (12)
Color Black
Torque 5.0 ± 0.5 lb/in
Speaker
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions.
For access, do the following: 1. Remove the left side cover. See “Left side
cover” on page 72. 2. Disconnect the cable from the system board. See “System
board” on page 60. 3. Remove the system board. See “System board” on page 130.
Removal steps Remove the speaker.
Chapter 7. Hardware removal and installation 131
Rear power button
Prerequisite Before you start, read Generic Safety and Compliance Notices, and
print the following instructions. For access, do the following:
1. Remove the left side cover. See “Left side cover” on page 72. 2. Remove
the system board. See “System board” on page 130. Removal steps Remove the
rear power button.
Cable connection
Note: The connectors on the cards or system board might look slightly
different from the illustrations. 132 PX Hardware Maintenance Manual
Notes: · C0 connector priority is higher than C1 connector. · MCIO connector 1
priority is higher than MCIO connector 2. · Front access bay 2+5 priority is
higher than front access bay 3+6 . Figure 4. Cable connection for BCM9560 RAID
AIC
Notes: · MCIO connector 1 priority is higher than MCIO connector 2. · Front
access bay 2+5 priority is higher than front access bay 3+6. Figure 5. Cable
connection for M.2 SSD enclosure
Chapter 7. Hardware removal and installation 133
Figure 6. GFX GV100/RTX A5500/RTX A4500/RTX 5000 Ada/RTX 4500 Ada/RTX 4000 Ada
Aux power connection
Figure 7. GFX RTX A6000/RTX 6000 Ada Aux power connection 134 PX Hardware
Maintenance Manual
Note: When the NVIDIA Quadro SYNC II card and the graphics card are located in
the upper PCIe card area and lower PCIe card area respectively, ensure that
you remove the memory fan duct to route the SYNC II card cable and power cable
through the cable slot of the memory fan duct as illustrated above. Figure 8.
Cable connection for NVIDIA Quadro SYNC II card
Chapter 7. Hardware removal and installation 135
136 PX Hardware Maintenance Manual
Chapter 8. Notices and trademarks
Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe
any Lenovo intellectual property right may be used instead. However, it is the
user’s responsibility to evaluate and verify the operatio
References
- Lenovo Computer Parts | Genuine Replacement Parts | Lenovo Support US
- Lenovo™ ThinkStation™ Software - Diagnostic Codes
- English Community-Lenovo Community
- Official Lenovo Laptop, Accessories & PC Support - Lenovo Support US
- Official Lenovo Laptop, Accessories & PC Support - Lenovo Support US
- Lenovo Support | Drivers, Troubleshooting, Warranty, Repair | Lenovo Support US
- Lenovo Computer Parts | Genuine Replacement Parts | Lenovo Support US
- Page Not Found - Lenovo Support US
- Microsoft Support
- Accessibility Features Content | Lenovo US
- Popular Topics: Tips for PC's - Lenovo Support US
- Lenovo™ ThinkStation Software
- Lenovo™ ThinkStation™ Software - Diagnostic Codes
- Lenovo™ ThinkStation™ Software - Diagnostics
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>