AOKPRO B0BTHN87LF Adjustable Standing Desk Instructions
- June 15, 2024
- AOKPRO
Table of Contents
AOKPRO B0BTHN87LF Adjustable Standing Desk
Safety Instructions
The desk must be initialized before first use. Read the initialization chapter prior to operation.
- Read and understand this manual before attempting to install or operate Assure that everyone who uses this product is informed of the contents of this manual. This is the responsibility of the Purchaser.
- Not intended for use by young children or for those persons who require supervision.
- Do not open any of the components – legs, control box, or controller. There is a risk of electric shock.
- Assemble desk on a flat and level surface.
Use & Liability
Safe use of this product is possible only when the operating instructions are
read completely and the instructions contained are strictly observed. Persons
who do not have the necessary experience or knowledge of this product must not
use the product. Persons with reduced physical or mental abilities should not
use this product, unless they are under supervision or they have been
thoroughly instructed in the use of the apparatus by a person who is
responsible for the safety of these persons. Children should be closely
supervised to ensure that they do not play with this product.
Before You Begin
Layout all components and hardware. Visually examine and make sure components are free of damage. If there is visual damage to any component, it must not be installed. Two people are needed to turn or move the desk and some of it’s components. When moving or turning the assembled desk, grab the legs, not the desk top. Make sure to assemble on a soft and non-abrasive surface to avoid scratches. Check all connections and cables. Make sure control box is connected to a power outlet. If the control box makes unusual noises or emits an odor, switch power off immediately.
Brief description of Adjustable Standing Desk components
Main accessories
Installation accessories and tools
Installation accessories and tools
Preparation before
Will you buy our desktop(or your own desktop board) With the back facing up, place it on a so and flat surface. Put a cloth bag or foam board under the top to protect the surface
Layout all components and hardware. Examine each and make sure components are without damage
Installation
Step 1：Connect the handset and the control box with the handset cable 
Step 2: Attach the bottom feet 
Step 3: Put the side bar 
Step 4: Turn the desk frame over and put it on the backside of the table
top, adjust the position of the desk frame to match the nuts on the table
top. Then fasten the desk frame with the table top with 
Step 5: Controller Wiring Connect the power cable and the motor cable to the
corresponding ports in the control box.
Step 6: Turn the table over. Note that due to the heavy weight of the product, it must be turned over by two or more people
- DO NOT USE UNTIL INITIALIZATION IS COMPLETED
- DO not put weight on the desk yet.
Instructions for Intelligent
Control Panel
Initialization/Reset
- Press and hold or buttons together for 3 seconds, both columns starts moving down; and the LED display reads ” “
- Keep pressing the buttons until the columns reach the lowest height and the handset beeps, then the columns rise slightly and the LED display shows the height.
Height adjustment
Press and hold the or button, the columns move up or down; release the button when the desired height is reached. The LED display shows the current height. The columns also stop when they reach the highest or the lowest height.
Memory setting
- Move the columns to the desired height.
- Keep pressing the button and any of the three number buttons “1”, “2 “or” 3 “at the same time for 3 seconds. The handset beeps 3 times, and the height figure flashes for 3 seconds. The memory mode of the height for the number is complete. A maximum of three different heights could be set.
- ONE-TOUCH or CONSTANT TOUCH the number button, the columns move to the saved height. (SEE CONSTANT TOUCH / ONE-TOUCH SETTING)
Height limit setting
Set maximum height limit
1. Press or button to move the columns to the desired maximum height.
2. Press and hold the butto and for 3 seconds, the LED display shows . The
maximum height setting is complete.
Set minimum height limit
1. Press or button to move the columns to the desired minimum height.
2. Press and hold the button and for 3 seconds, the LED display shows “ “.
The minimum height setting is complete.
Remove height limit
Press and hold , and “” button for 3 seconds, ” ” is shown on the LED display, the height limit is removed.
Lock / Unlock
1. Press button for 3 seconds, the flashes on the LED display, the handset is
locked.
2. Press button for 3 seconds, the changed to the current height figure, the
handset is unlocked.
Height unit switch
The LED display could show the height in “cm” or “inch”. Keep pressing “2” and “3” for 3 seconds, the height unit could switch between “cm” and “inch Fall” stands for “cm Real” stands for “inch”.
Anti-Collision sensitivity
Press and hold , together for 3 seconds, the LED display shows the current sensitivity. Repeat the operation, the reads change from to . stands for high sensitivity; for low sensitivity.
One-Touch / Constant touch
• Constant-Touch requires a constant touch of the “1” “2”or”3 “button to move
the desktop to the preset memory location.
• One-Touch requires only one single touch of the “1” “2” or” 3) “button to
move the desktop to the preset memory height.
• Press and hold “ ” and “2” together for 3 seconds, the LED display shows ” ”
or “ . “ ” for constant touch; “ ” for one-touch.
Height Figure adjustment on LED display
1. Move both columns to the lowest height.
2. Pressing “ ” button for 10 seconds, the LED display flashes, adjust the
height figure on the LED display by and to the regired figure.
3. Pressing “ ” button for 5 seconds, the figure adjustment is complete.
Index of Malfunction and Repair
Service Information
Thank you for choosing our products, We hope that every product delivered to our customers can bring them better enjoyment! Please feel free to contact us via Email or Facebook if you have any concern.
Pay attention
Recommendations for the continual safe use of this product are stated on the final page of these instructions. Please retain for future reference.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>