BOSCH MESM Series Slow juicer Instruction Manual
- June 3, 2024
- Bosch
Table of Contents
BOSCH MESM Series Slow juicer
Intended use
This appliance is intended for domestic use only. The appliance is suitable
for squeezing fresh juice from fruit or vegetables. The appliance is suitable
for making sorbet from frozen fruit or vegetables when using the sorbet insert
piece. The appliance must not be used for processing other substances or
objects. Additional applications are possible if the accessories approved by
the manufacturer are used. Only use the appliance with approved genuine parts
and accessories. Never use the accessory parts for other appliances.
Only use the appliance indoors at room temperature and up to 2000 m above sea
level.
Important safety information
Read and follow the instruction manual carefully and keep for later reference! Enclose these instructions when you give this appliance to someone else. If the instructions for correct use of the appliance are not observed, the manufacturer’s liability for any resulting damage will be excluded.
This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and/or knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Keep children away from the appliance and connecting cable and do not allow them to use the appliance. Children shall not play with the appliance. Cleaning and user maintenance must not be made by children.
Risk of electric shock and fire!
- Connect and operate the appliance only in accordance with the specifications on the rating plate. Do not use the appliance if the power cord and/or appliance are damaged. Only our customer service may repair the appliance, e.g. by replacing a damaged power cord, in order to avoid hazards.
- Never connect the appliance to timer switches or remote-controllable sockets. Never leave the appliance unattended while it is switched on!
- Do not place the appliance on or near hot surfaces, e.g. hobs. The power cord must not come into contact with hot parts or be pulled across sharp edges.
- Never immerse the base unit in water or place it in the dishwasher. Do not steam-clean the appliance. Do not use the appliance with damp hands.
- After each use, whenever the appliance is unsupervised, prior to assembly, prior to disassembly, prior to cleaning and in the event of an error, the appliance must always be disconnected from the mains.
Risk of injury
- Before replacing accessories or additional parts which move during operation, the appliance must be switched off and disconnected from the power supply. Immediately after using the appliance, wait for it to stop.
- Only operate the appliance in its fully assembled state. Never operate it without a correctly placed and locked lid!
- Never reach into the feed chute with your hands during the operation. Do not insert any objects (e.g. wooden spoons) into the feed chute. Only use the pusher provided!
- Keep hands clear of rotating parts. Use the appliance only with genuine parts and accessories.
Risk of suffocation!
Do not allow children to play with packaging material.
Caution!
We recommend that the appliance is never switched on for longer than is
necessary to process the ingredients. Do not operate at no-load.
Important!
It is essential to clean the appliance thoroughly after each use or after it
has not been used for an extended period.
Congratulations on the purchase of your new Bosch appliance. You can find further information about our products on our website.
Overview
- Base unit/motor unit
- a Driveshaft
- b Marking G
- c Switch (3-level)
- ON = On
- O = Off
- Reversing function
- d Mains cable
- e LED-Ring
- f Marking O
- Juice drum
- a Seal for drive shaft
- b Aperture for juice
- c Sealing cap for juice (drip-stop)
- d Aperture for fruit pulp
- e Adjusting lever with a seal for fruit pulp and markings
- f Seal for fruit pulp
- g Marking F
- h Scale
- Rotating brush with silicon scraper
- Strainer insert pieces
- a Fine
- b Coarse
- c Marking
- Sorbet insert piece*
- a Marking
- Juicer screw
- Pusher
- Lid
- a Feed chute
- b Marking
- Container for juice
- Container for fruit pulp
- Cleaning brush
- Recipe book
Depending on the model
Before using it for the first time
Before the new appliance can be used, it must be fully unpacked, cleaned and checked.
Caution!
Never operate a damaged appliance!
- Remove the base unit and all accessories from the packaging and dispose of all packing materials.
- Check that all the parts are present and examine them for obvious damage.
- Thoroughly clean and dry all parts before using them for the first time.
Symbols and markings
- Fit the lid ( ) and screw on securely ( ).
- Marking on the base unit for fitting the lid and for the insert pieces.
- Marking on the insert pieces.
- Fit juice drum ( ).
- Marking on the base unit for fitting the juicing drum.
- Max. capacity. If the juice reaches the 350 ml marking, finish processing and empty the juicing drum.
- Markings on the juicing drum for the adjusting lever *: cleaning, little fruit pulp, lot of fruit pulp.
Adjusting lever/seal for fruit pulp
Models with adjusting lever for seal Fig. F
The consistency of the juice can be controlled using the adjusting lever for
fruit pulp.
- For juice with a lot of fruit pulp, slide the lever to the right ( ).
- For juice with less fruit pulp, slide the lever toward the center ( ).
- To clean/rinse out, remove the juicing drum, turn over and slide the lever to the stop as shown ( ).
Models with seal Fig. G
The seal for fruit pulp ensures that the juice has a constant consistency
.
- When making juice or sorbet, the seal must sit correctly in the aperture for fruit pulp.
- To clean/rinse out, remove the juice drum, turn over and pull out the seal.
Preparation
Risk of injury
Do not insert the mains plug until all preparations for working with the
appliance are complete and all individual parts are assembled correctly and
connected to the base unit.
Caution!
Never place the juice drum onto the base unit without the seal for the drive
shaft. Ensure that the seal also sits correctly after placing it onto the base
unit.
Important:
Before re-assembling, check that the aperture is completely closed by the seal
for fruit pulp. “Adjusting lever/seal for fruit pulp”
Preparing to squeeze juice
Image sequence B
-
Place the base unit onto a stable and level work surface.
-
Place the juice drum onto the base unit. When doing so, align the recesses on the base of the juice drum with the counterparts on the base unit (observe markings). The juice drum must sit flush and firmly on top of the base unit.
-
Place the rotating brush into the juice drum.
-
Place the desired strainer insert piece (coarse or fine) into the rotating brush (observe markings ).
Important: Ensure that the aperture and the notches on the base sit firmly on top of their counterparts on the juice drum. The strainer insert piece must not be able to turn any further. -
Place the juicer screw into the strainer and press down until it sits on top of the drive shaft.
-
Place the lid on top ( ) and turn it as far as possible in a clockwise direction ( ).
Preparing to make sorbet
Image sequence C
-
Place the base unit onto a stable and level work surface.
-
Place the juicing drum onto the base unit. When doing so, align the recesses on the base of the juicing drum with the counterparts on the base unit (observe markings). The juice drum must sit flush and firmly on top of the base unit.
-
Place the sorbet insert piece in the juicing drum (observe markings ).
Important: Ensure that the aperture and the notches on the base sit firmly on top of their counterparts on the juicing drum. The sorbet insert piece must not be able to turn any further. -
Place the juicer screw into the sorbet insert piece and press down until it sits on top of the drive shaft.
-
Place the lid on top ( ) and turn it as far as possible in a clockwise direction ( ).
Preparing food
Important:
Only process ripe fruit and vegetables. Unripe or over-ripe fruit will very
quickly clog the juicer screw and its strainer.
- Remove stones or seeds (e.g. for plums, peaches, cherries etc.).
- Remove hard peel/skin (e.g. for melons, pineapples, cucumbers, potatoes etc.).
- Fruits and vegetables with thin peel/skin (e.g. apples, pears, carrots, radishes, salad, cabbages, parsley, spinach, grapes, strawberries, celery etc.) only need to be washed.
- Peel citrus fruits and remove the white pith, as the juice may taste bitter otherwise.
- Chop up large fruits and vegetables beforehand so they fit into the feed chute without having to force them in.
Use
Risk of injury
- Only operate the appliance in its fully assembled state.
- Never operate it without a correctly placed and locked lid.
- Do not reach into the feed chute with your fingers. Use the supplied pusher only!
Caution!
Always use the sorbet insert piece to process frozen fruits. Do not process
fruit that gets very hard by freezing (eg. strawberries).
Important:
If the juice reaches the 350 ml mark, finish processing and empty the juicing
drum.
Squeezing juice
Image sequence D
- Prepare the appliance as described. “Preparing to squeeze juice”
- Place one container under each of the apertures for juice and fruit pulp.
- Open the sealing cap for the juice.
- Slide the adjusting lever for fruit pulp (depending on the model) as wished either toward the center ( ) or all the way to the right ( ).
- Plug the mains plug into the mains. Move the switch to ON. The appliance starts. The LED ring lights up (depending on the model). The rotating brush rotates.
- Add the prepared food to the feed chute.
- Only use the pusher provided to push the food further. The juice flows into the right-hand container. The squeezed fruit pulp will be collected in the left-hand container.
- Once the processing is complete or the juice container is full, move the switch to O and wait for the appliance to come to a stop.
- Close the sealing cap for the juice and empty the container.
Notes:
- To improve the amount of juice produced, preferably process ingredients containing lots of juice at the beginning and end of processing (e.g. oranges, tomatoes, watermelon, etc.). Process hard or fibrous Ingredients in between.
- Fill the food into the feed chute one portion at a time.
- Stuffing it in excessively does not accelerate the processing and leads to the drum overflowing.
Making sorbet
Image sequence E
-
Prepare the appliance as described with the sorbet insert piece. “Preparing to make sorbet”.
Place a container under the aperture for the juice. Open the sealing cap for the juice. -
Plug the mains plug into the mains. Move the switch to ON. The appliance starts. The LED ring lights up (depending on the model).
-
Add the frozen food to the feed chute.
-
Only use the pusher provided to push the food further. The sorbet produced will be collected in the container.
Reversing function
The reversing function is designed to release food that has got stuck by
briefly running the worm gear in reverse.
- Move the switch to O and wait for the appliance to come to a stop.
- Move the switch to and keep it pressed.
- After approx. In 3-5 seconds, release the switch and wait for the appliance to come to a stop.
- Move the switch to ON and continue with the juicing.
Note:
If the food that has got stuck is not released briefly put the appliance into
reverse, switch the appliance off, unplug it and clean it. X “Cleaning” see
page 19
Warning!
The reversing function must be used for several seconds or it will no longer
be possible to switch on the appliance.
After using the appliance
- Empty both containers and then place them under the apertures for juice and fruit pulp again.
- Close the sealing cap and slide the adjusting lever for the fruit pulp all the way to the right.
- Pour a little water (approx. 150 ml) into the feed chute and move the switch to ON.
- After a short time, open the sealing cap and slide the adjusting lever for fruit pulp all the way to the left.
- Let the appliance slow down and stop completely before switching it off.
- Move the switch to O and wait for the appliance to come to a stop.
- Disconnect the mains plug.
- Clean all parts immediately after use.
Cleaning
The appliance and the individual parts used must be thoroughly cleaned after each use.
Risk of electric shock!
- Unplug the appliance before cleaning it.
- Never immerse the base unit in liquids and do not clean in the dishwasher.
- Do not steam-clean the appliance.
Caution!
- Do not use any cleaning agents containing alcohol or spirits.
- Do not use any sharp, pointed or metal objects.
- Do not use abrasive cloths or cleaning agents.
- Do not clean the individual parts in the dishwasher.
Notes:
- When processing food such as carrots, plastic parts may become discolored. This can be removed with a few drops of cooking oil.
- Completely open the seal for fruit pulp. “Adjusting lever/seal for fruit pulp”.
In Fig. H you will find a summary of how to clean the individual parts
.
Dismantling the appliance
- Rotate the lid to the marking ( ) and remove it.
- Remove the assembled juice drum.
- Then dismantle the juicer screw, strainer, or sorbet insert piece, and the rotating brush one by one.
Note:
If the individual parts in the juicing drum are jammed (e.g. due to remnants
of fruit), proceed as follows.
Image sequence I
- Turn the juice drum over, putting a cloth underneath.
- On the underside carefully press on the drive shaft of the juicer screw until it releases.
- Remove all individual parts.
Cleaning the base unit
- Wipe the outside of the base unit with a soft, damp cloth and dry off.
Cleaning additional parts
- Clean the juice drum, rotating brush, strainer insert pieces, sorbet insert piece, juicer screw and pusher with detergent solution, a soft cloth/sponge and the brush provided or place them in the dishwasher.
- The brush provided is particularly suitable for thorough cleaning of the apertures for juice and for fruit pulp.
- Clean the lid with a detergent solution and a soft cloth/sponge or a soft brush and then rinse under running water.
- Leave all parts to dry or dry them off with a cloth.
Disposal
Dispose of packaging in an environmentally-friendly manner. This appliance
is labeled in accordance with European Directive 2012/19/EU concerning used
electrical and electronic appliances (waste electrical and electronic
equipment – WEEE). The guideline determines the framework for the return and
recycling of used appliances as applicable throughout the EU. Please ask your
specialist retailer about current disposal facilities.
Guarantee
The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold. Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.
Changes reserved.
Troubleshooting
| Problem | Reason | Remedy |
|---|---|---|
| The appliance does not start when switched on. | Appliance has no power | |
| supply. | Insert the mains plug into the socket. | |
| The lid is not sitting correctly on the juice drum. | Place the lid onto the |
juice drum correctly. Observe the markings. If the lid cannot be closed,
disassemble and reassemble the parts again. Ensure that all individual parts
sit correctly.
The appliance stopped during use.| The reversing function must be used for
several seconds or it will no longer be possible to switch on the appliance.
The appliance stops during use.| Too much food to be squeezed or hard
seeds/stalks in the appliance.| The reversing function must be used for
several seconds or it will no longer be possible to switch on the appliance.
X “Reversing function”
The lid is not sitting correctly on the juice drum.| Place the lid onto the
juice drum correctly.
The juice drum cannot be positioned on the base unit correctly.| The adjusting
lever for fruit pulp is incorrectly adjusted or the seal is not in the correct
position.| Check the setting/seal.
X “Adjusting lever/seal for fruit pulp”
The juice is too runny or too viscous.| The adjusting lever for fruit pulp is incorrectly adjusted or the seal is not in the correct position.| Check the setting/seal.
X “Adjusting lever/seal for fruit pulp”
Quantity in the appliance is too large.| Do not process excessive quantities
simultaneously.
The appliance motor is running loudly.| The appliance is incorrectly
assembled.| Disassemble and reassemble the appliance as described. X
“Preparation”
If you are unable to solve the problem, always call the hotline!
You will find the telephone numbers at the back of these instructions.
Thank you for buying a Bosch Home Appliance!
Register your new device on MyBosch now and profit directly from:
- Expert tips & tricks for your appliance
- Warranty extension options
- Discounts for accessories & spare parts
- Digital manual and all appliance data at hand
- Easy access to Bosch Home Appliances Service
Free and easy registration – also on mobile phones: www.bosch- home.com/welcome
Looking for help? You´ll find it here.
Expert advice for your Bosch home appliances need help with problems or a
repair from Bosch experts.
Find out everything about the many ways Bosch can support you: www.bosch-
home.com/service
Contact data of all countries are listed in the attached service directory.
BSH Hausgeräte GmbH
Carl-Wery-Straße 34 81739 München, GERMANY A Bosch Company
www.bosch-home.com.
Valid within Great Britain:
Imported to Great Britain by BSH Home Appliances Ltd. Grand Union House
Old Wolverton Road Wolverton, Milton Keynes MK12 5PT
United Kingdom.
References
- Home Appliances Global Website | Bosch
- Home Appliances Global Website | Bosch
- Bosch Service | Service worldwide
- Welcome to MyBosch
- SERBÄ°S
- Bosch Yetkili Servis | Bosch Ev Aletleri Yetkili Servisi
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>