SUNCO LIGHTING B096H2L1TC 5-6 Inch Selectable Retrofit Installation Guide
- June 4, 2024
- Sunco Lighting
Table of Contents
SUNCO LIGHTING B096H2L1TC 5-6 Inch Selectable Retrofit
COMPONENTS
EASY INSTALLATION
-
Turn off power at fuse or circuit breaker before installing.
-
Locate recessed can in ceiling. Remove existing light fixture. Allow time for fixture to cool before removing.
-
Using a screwdriver, adjust spring clips according to size of existing can (5” or 6”).
Slide bracket into position, then retighten screw. -
Determine type of connector available in your recessed can. TP24 Connector
E26 Base -
Connect appropriate adapter.
(E26 or TP24) to the retrofit light. NOTE: Ensure all wires are attached to connectors. -
Turn on power and test light.
-
Slide CCT switch on retrofit to choose from 5 color temperature options.
Turn off light switch and continue install. -
Tuck all wires into can and line up trim with opening in ceiling.
-
Push light into can until secure. Spring clips will hold light in place.
COMPATIBLE DIMMERS
-
Leviton
6674-P0W -
Lutro
MACL-153M
Caseta Smart
DVCL-153P
DVELV-300P -
Legrand
RHCL453PW
SPECIFICATIONS
- Voltage 120VAC
- Wattage 13W
- Moisture Rating Damp
- Housing Material PC + Aluminium
- Weight 0.37 lb
- Warranty 7 Years
WARNING
To reduce the risk of fire, electric shock, or physical injury:
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.
- This product should be installed by a person familiar with the construction and operation of the product and the hazards involved.
- Installers should examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
- Install this retrofit only in luminaires that match the construction features and dimensions shown in the diagrams provided. Ensure the input rating of the retrofit does not exceed the input rating of the luminaire.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Do not install directly over a heat source, on a radiant heating ceiling, or on the surface of combustible material. Do not cover with flammable material.
- Proper grounding is required to ensure safety. This fixture is not suitable for wet environments.
- Use safety precautions and abide by regional and local laws or regulations.
- Safety eyeglasses and gloves are recommended.
FCC NOTES
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>