RACE CHIP 2BDRI-SC sc SC Smart Controller User Manual
- June 15, 2024
- RACE CHIP
Table of Contents
RACE CHIP 2BDRI-SC sc SC Smart Controller User Manual
PLEASE BEFORE USE READ!
Overview and explanation of symbols
1 Scope of delivery
2 Technical overview
2.1. Control panels
2.2. Display
• 1.69“ LCD TFT Touch Display
• Resolution 240 x 280p
2.3. Battery
• Battery capacity 200mAh
• Battery voltage 3.7V
• Battery life in standby mode approx. 150 hours
• Battery life in continuous mode approx. 24 hours
3 Installation
3.1. Positioning of the controller
Remove the foil on one side of the adhesive dot and stick it to the round
base. Position the controller so that it is clearly visible and easy for the
driver to reach. For legal reasons, the passenger must not have access to the
mounted controller while driving!
Once you have selected a suitable location, peel off the second protective
film from the adhesive dot and attach the controller to the dashboard.
Make sure that the surface is clean and free of grease.
The controller must not interfere with the operation of, or visibility to, any other controls on your car.
3.2. Expand | Disconnect from the base
The controller can be removed from the vehicle for various reasons.
- Use of the anti-theft protection
- Charge the battery outside of the vehicle
To loosen the base, turn the operating part counterclockwise by 90° and then pull it off
To reattach the controller to the base, proceed as follows:
Place the controller, turned 90° to the left, on the base and then turn it clockwise 90° until it comes to a firm stop
4 Operation
4.1. Connection | 4.1.1. Set up controller and app at the same time
After connection, the XLR5 must be taught to the individual accelerator pedal. Please follow the instructions in the app:
The controller is now automatically connected to the Brainbox.
4.1.2. Set up controller individually
If the controller was not registered and connected during the first app
connection, it can be connected subsequently
The controller is only compatible with XLR5 modules. Previous modules are only controllable with the app and the wired controllers
4 Operation
4.2. Drive Modes | Home Screen
If there is no connection to the XLR5, a clock is displayed. The type of clock
can be selected in the menu between analog and digital
4.3. Fine tuning
4.4. Menu
Updates are performed with the help of the RaceChip+ app When an update is available, you will be notified in the app. Follow the instructions in the app to perform the update.
4.5 Other functions | 4.5.1 Anti-theft protection
The anti-theft system uses the controller as an additional key to release the throttle pedal. When it is activated, nothing initially changes on the vehicle As soon as the vehicle goes into idle mode (usually about 5 minutes after it is locked), the anti-theft protection becomes active and suppresses the throttle pedal signal. Until the controller reconnects to the Brainbox, or the anti-theft is deactivated via the RaceChip+ app, pressing the throttle pedal will not cause the engine to respond
For full anti-theft protection, turn off the controller and simply take the controller with you when you leave the vehicle
4.5.2. Limiter
The limiter can limit the throttle pedal. Via the limiter fi ne tuning setup, you can choose how much the throttle pedal should be limited It is adjustable in the range between 40% and 80%.
For legal reasons, the throttle may not be fully limited and must return to the standard value at full throttle. This feels like activating a kickdown in this mode.
4.5.3. Valet
Valet-Mode is only enabled for use on private roads and parking lots In this mode, the throttle pedal can be limited between 30% and 50% Even at full throttle, the limited accelerator pedal characteristic is maintained
This mode is designed for a valet service, so the driver can only move the vehicle at a leisurely pace After activating the mode, we recommend removing the control unit from the vehicle before handing it over to the valet Since this mode can only be deactivated with the controller or the RaceChip+ app, the throttle pedal will remain in valet mode until you receive the vehicle back and deactivate the mode with the controller
4.5.4. Flashlight
The flashlight switches the screen to white. This allows the controller to be used as a makeshift flashlight to better locate the throttle pedal sensor when installing the XLR5, for example
5. Warnings
The controller is equipped with a lithium-ion battery. Therefore, the following safety instructions apply:
- Do not disassemble the controller.
- Only use suitable charging cables (see chapter: Charging).
- Do not use damaged USB-C cables.
- Do not use it if it is damaged. There is a risk of fire!
- Do not expose to direct sunlight or heat sources for long periods of time.
- There is a risk of overheating and fire!
6 Troubleshooting
If the function of the controller is not as desired, you will find initial help for troubleshooting here.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC warning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
IC warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
7 Contact
Our Customer Service is ready to help!
Find out how to contact us at:
www.racechip.com/service-support
Please have your customer details close by when you contact us.
Follow us on:
racechipchiptuning
racechipchiptuning
Legal notice
RaceChip Chiptuning GmbH & Co. KG
Karl-Frasch-Str. 14
73037 Göppingen
Germany
Sales tax identifi cation number: DE 260672432
Registered at District Court of Ulm: HRA 721734
Tax number: 63079/11153
Personally liable partner:
RaceChip Chiptuning Verwaltungs GmbH
Chief executives: Dirk Bongardt, Kai Döhler
Head offi ce: Karl-Frasch-Str. 14, 73037 Göppingen, Germany Registered at HRB
District Court of Ulm: HRB 724254
Read More About This Manual & Download PDF:
References
- RaceChip+ – Apps bei Google Play
- RaceChip+ im App Store
- Customer Service - We are always there for you - RaceChip
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>