SCHULZE E-Power Duo Electric Heat Press Instruction Manual

SCHULZE E-Power Duo Electric Heat Press

Product Information

Specifications

• Dimensions of the press: Not specified
• Weight: Not specified
• Power supply: Not specified
• Rated power (with plate 38 x 45 cm): Not specified
• Rated power (with plate 40 x 50 cm): Not specified
• Temperature range: Not specified
• Heating time: 1 sec. – 99:59 min.
• Max. pressure: 4.5 bar
• Fuse: B 16A
• Noise: Less than 70dB (A)

Product Usage Instructions

1. Introduction

The SCHULZE E-Power Duo Press is an electric heat press. This section provides an overview of the content and warning pictogramson the machine.

2. Initiation

This section covers tips for transport, installation of the heat press, power supply, and initiation of the heat press.

3. Working with the heat press

This section explains the programming of electronics, error codes, usage of the heat press with example settings, druckeinstellung (printing settings), and instructions for replacement of heating plates, replacement and rotation of base plates, and temperature correction.

4. Maintenance and replacement of parts

This section provides instructions for daily and monthly maintenance, as well as instructions for the replacement of the main fuse, silicone mat, electronics, electronics keyboard, thermal fuse, and temperature sensor. It also includes a troubleshooting guide.

5. Documentation

This section includes a wiring diagram, configuration of the frequency inverter, warranty terms and conditions, and conformancedeclaration.

Warning

• ATTENTION! MOVING ELEMENTS

• ATTENTION! HAND CRUSH HAZARD
  

• ATTENTION! DANGER
  

• ATTENTION! HIGH VOLTAGE

• ATTENTION! HOT SURFACE

Construction of the machine

1. Base
2. Heating plate
3. Handhold
4. Keyboard
5. Display of electronic devices
6. Switch START
7. Spiral tube with connection to the heating plate
8. Connection piece
9. Base plate
10. Pressure adjustment
11. Power supply cable
12. Main switch
13. Emergency button

Technical data

Replaceable heating plates

For the heat press there are several heating plates available. The instruction for the replacement can be found in chapter 3.5

1. Heating plate:  40 x 50 cm
2. Heating plate: 38 x 45 cm
3. Heating plate: 20 x 20 cm
4. Heating plate: 10 x 13 cm

Replaceable base plates

The machine has been equipped with different safety arrangements, to assure a safety working procedure.

• Main fuse B 16A
  In case of overcharge, the main fuse prevents the heat press from getting damaged. Once the fuse was switched of, it has to be activated. The instruction for activation of the main fuse can be found in the chapter 4.3.

• Thermal fuse
  The thermal fuse is situated directly on the heating plate and it stops the power supply if the temperature exceeds ~260°C. If the fuse is activated, the temperature sinks down to 90°C. After that the power supply gets activated again and the temperature of the heating plate rises and it’s possible to continue the work with the press. Over time the thermal fuse may wear out and cut off the power supply by lower temperature, for example by 180°C. In such case it’s needed to replace the thermal fuse as soon as possible. The instruction for the replacement of the thermal fuse can be found in chapter 4.9.

• Automatic switch-off
  If the press doesn’t get opened within 10 seconds after the pressing progress, the heating element switches off automatically, to avoid fire danger.

• Emergency button
  The emergency button has been installed to eliminate the residual risks. In case of emergency push the red emergency button. It is situated in front of the press. The press will open automatically. To resume work, the button has to be pulled back again.

• Mechanical emergency button
  If the emergency button doesn’t work due to power failure, the machine switches automatically to the mechanical emergency mode. This mode allows to stop the work of the machine. The press will open automatically using an independent mechanical system.

Safety arrangements at the workplace

• Set-up and installation
  Set-up and installation of the device has to be done under supervision of an authorized person by the company owner. Depending on the model and weight of the heat press, the installation has to be done by 2 or more persons. The press should be situated on the flat, non-inflammable surface, in a room with constant temperature and constant moisture. Keep the machine away from dusty rooms, because dust could have a negative influence on some parts of the machine. Very important! The machine may be connected only to an installation provided with a protection against electric shock. The machine is destined for industrial use only.

• Testing the machine
  After the correct installation of the machine it is important to ensure that the machine works properly, is not damaged after the transportation and has no safety defects. The testing can only be done by the employer or other authorized persons. It is mandatory to guarantee a correct installation and safe usage of the machine. After receiving the machine, check the packaging. The testing should be protocoled. If any irregularities regarding functionality or safety are found during the testing, these has to be noted and reported to Walter Schulze GmbH in written form within 7 days. Until the clarification the machine can not be used.

• Information and education
  According to §81 the industrial law and § 14 employment protection law (german law), the advice from he producer and general safety arrangements at the workplace, the employer has to make arrangements to give all information about the safety, function and the range of application to the user. In particular the user needs to be acquainted with the complete manual and be explicitly informed of the dangers of working with the machine. The details have to be explained in a coherent form and language. Every user is obligated to a safe usage of the machine and to read the manual instruction before each operator starts working with the machine. Using the machine, means that the operator has read the instruction and is aware of the possible risks of working with the machine.

• Safety
  In order to ensure optimized safety, please read the manual instruction precisely. Only one person is allowed to work on the machine at a time. The machine has to be under supervision the whole time, when it’s working. Supervise the machine till it is switched off and the plug is pulled out. Pressure adjustment has to be done when the press is open. There should be no unauthorized persons near the machine while it’s working. Beware of the heating plate – risk of burns. It is allowed to use personal protective equipment. Attention! The press opens automatically – keep the safety clearance. In case of emergency or a dangerous situation, please push the emergency stop switch. It is situated in the front of the press. The machine will stop immediately. The plug has to be pulled out of the power supply, while maintenance. Using the press with certain materials may create a strong smell. That’s why the operator should evaluate the need for a ventilation system at the workplace. The type of ventilation should be used as needed and depends on the size of the room and used inks. The space in front of the press has to be wide enough to let nothing disturb the user at work. The press has to be installed at a place which gives enough space on both sides to put the material on. Do not install the machine in doors. Floors or busy places. All wires should be placed in a safe way, to make sure they will not pose a threat for the person working at the machine or passing it. In case of damage the wires, stop work, turn off the press, unplug the machine and contact the service. All repairs should be performed after consulting the service. Do not remove machine covers while the machine is working.

• Correct operating position

• The operator must have free access to all buttons and switches. Safe position allows operator to switch on the emergency button in every moment.
  Other risks and dangers
  The movement of the heating plate is performed with two-hand switching circuits and bottom position microswitch. Such combination forces operator to keep both hands in the safe zone, till the heating plate reaches safe position. Two-hand switch prevents the operator from placing hands between heating plate and base plate. Additionally the press has been equipped with an end- switch for position of the heating plate, which prevents the movement of the heating plate from inappropriate position. Activation of the work is only possible if the heating plate is situated directly above the base plate. There are some movable elements on the machine, which can cause injuries of hands or fingers. For reasons of workability, these elements cannot be eliminated. It is important to work with the machine with great care and be alert to avoid other dangerous situations. The machine should be operated in accordance with the manufacturer’s recommendations to avoid risks. The machine complies with the essential requirements laid down in regulation for machines. Above information has been worked out in accordance with the standards PN-EN 12100:2012. The machine is constantly upgraded in order to improve its safety. All comments regarding the contents of this manual can be addressed to the distributor or manufacturer.

Environmental protection

The packaging of the device must be disposed of in accordance with the applicable rules. Do not dispose of the equipment marked with an together with your household waste. No longer needed machines may be returned to the manufacturer or disposed of in an environmentally friendly manner by means of appropriate disposal systems.

Initiation

Notes regarding transportation

The SCHULZE E-Power Duo Press is covered in protective foil and fixed onto the pallet for transport. Right after receiving it must be checked if the cardboard and the machine are in good condition without damages. It has to be done just after receiving the goods from the transportation company and in accompany of a responsible person. If the machine will be send at a later date to some other place, it has to be fixed onto the pallet the same way as when it was delivered. The press has to be cold for the transport and the base plates have to be removed and protected against damage. The upper part of the machine has to be blocked in order to prevent it from being moved.

Installation of the heat press

The heat press is placed on a base. The unpacking and moving of the heart press has to be done by 2 or more persons. ATTENTION!!!The upper part of the heat press can pivot to the sides. Risks of injury. The machine has to be moved with care, and attention has to be payed to keep the balance. The machine should be situated on a stable surface and aligned horizontally.

Power supply

The SCHULZE E- Power Duo Press has to be connected to the installation 230VAC/50Hz. The device is equipped with a plug. It has to be checked if the socket is in good condition, and special attention should be paid to the presence of connected safety circuit inside. Very important! The machine may be connected only to an installation provided with protection against electric shock (ELCB – earth leakage circuit breaker). In case of doubt ask your licensed electrician to check the wiring. Connecting the machine to a socket that is not earthed or where the earthing does not work properly, is hazardous to health and dangerous for the machine. Any damages arising from improper plugging invalidates the warranty.

Initiation of the heat press

Before the initial start up make sure that the power outlet is in the right condition and that the grounding is connected to the power outlet. After connecting to power supply, the press is able to use. While powering up the press, the movable part has to be in the upper position, which means that the press has to be open. The press also has to be open while heating up. In order to switch the machine on, use the green switch, which is situated on the left side of the heat press. The green switch lights up and the press is heating up to the programmed temperature. Start the press cycle by pressing both green buttons START. If the work is finished, the press has to be switched off and the plug has to be pulled out.

Working with the heat press

After switching on the press, the current temperature is shown on the display and the press heats up. Change settings:

1. The programming mode shows when you press Setup for about 3 seconds, until the LED1 blinks up.

2. LED 1 blinks and the programmed temperature is shown on the display. The programming mode is activated.

3. The temperature gets programmed with button “+” and “-”. Temperature settings have been saved.

4. Press Setup shortly. The programmed time is shown on the display. Press the button “+” or “-” to adjust the time. Time settings has been saved.

5. Press Setup shortly. The programmed time for prepressing is shown on the display. Press the button “+” or “-” to adjust the time for prepressing. Time settings has been saved.

6. Press Setup shortly to leave the programming mode. New settings has been saved.
   or:

7. 6. Press the Setup for about 3 seconds to enter the settings for ECO mode.

8. Switch between ECO modes using “+” and “-” buttons:

   • „Eco 0” – ECO Mode is turned off,
   • „Eco 0,5” – der ECO Modus wurde eingeschaltet, nach 30 Minuten sinkt die Temperatur der Heizplatte um 50°C ab, dann nach 60 Minuten werden die Heizelemente ausgeschaltet.
   • „Eco 1.0” – der ECO Modus wurde eingeschaltet, nach 60 Minuten sinkt die Temperatur der Heizplatte um 50°C ab, dann nach 60 Minuten werden die Heizelemente ausgeschaltet.
   • „Eco 2.0” – der ECO Modus wurde eingeschaltet, nach 120 Minuten sinkt die Temperatur der Heizplatte um 50°C ab, dann nach 60 Minuten werden die Heizelemente ausgeschaltet.

9. Die Taste Setup kurz drücken. Mit den Tasten „+“ oder „-“ stellen Sie den Ton ein.

10. Um den Programmiervorgang zu beenden, drücken Sie kurz die Taste Setup.

Control of adjusted temperature

If you want to control which temperature is adjusted at the moment, press button “+”. The temperature shows up on the display.

Control of adjusted time

If you want to control which time is adjusted at the moment, press button “-”. The time shows up on the display.

Error codes

The electronic devices of the SCHULZE E-Power Duo Press controls the main functions of the press.

List of possible messages:

• ERR.1 – No connection of the electronic devices to the temperature sensor, (Temperature sensor defect/ cable not connected) ERR.2 – Connection of electronic devices and temperature sensor bypassed , (Temperature sensor defect/)
• ERR.3 – Resistor of temperature sensor too low. The temperature range of the electronic devices is deceeded.
• ERR.4 – Resistor of temperature sensor too high. The temperature range of the electronic devices exceeded.
• ERR.5 – No temperature rise within 3 minutes even if heating element is switched on. (Temperature fuse is defect)
• ERR.6 – No reduction of the temperature within 3 minutes even if heating element is turned off. (Power relay CRYDOM is defect) ERR.7 – Temperature too high, over 240°C (Power relay CRYDOM is defect)
• ERR.3 and ERR.4 can occur if the electronic devices are not programmed properly.

Usage of the heat press and example settings

This press is used to put transfers and transferfilms on textiles. To get good achievements, get in contact with the producer of the textiles. Here are some settings:

• Film Flex 150°C – 160°C Time 12 Seconds
• Film Flex S 155°C – 160°C Time 12 Seconds
• Film Flock 150°C – 160°C Time 15 Seconds
• Sublimation Film 190°C – 205°C Time 50 Seconds

Before each pressing procedure make a prepressing test and check the wash resistance.

Pressure adjustment

With SCHULZE E-Power Duo Press it’s possible to adjust the pressure settings very precisely. Pressure can be adjusted with a knob, which is situated in the front of the press. Follow the instructions below to adjust the pressure:

1. Open the press.
2. Turn the knob (picture):
   • to the left, to reduce the pressure
   • to the right, to increase the pressure
3. Close the press to check the new settings.

If the pressure adjustment is too high, it can cause damages of the machine. This type of damages are excluded of the warranty.

Instruction for replacement of the heating plate

To replace the heating plate, switch off and unplug the heat press. The press has to be cold. Unplug the heating plate from the press (picture 1). Loosen fixation screw with an hex key. (picture 2). Hold the heating plate and after it’s fully unscrewed, put it on the base plate (picture 3). Take the heating plate carefully and put it on a soft underground, because the Teflon cover could not get damaged. Then take the new heating plate and tighten it with an hex key Connect the heating plate with the press. The heating plate can’t be rotated.

Instruction for replacement and rotation of the base plate

To replace the base plate lose the fixation screws (picture) and remove the base plate. After replacing the base plate, tighten the fixation screws again (the pointed sides have to face up). To make pulling clothes over the base plate easier, turn the base plate by 90°. Lose the fixation screws, turn the plate and tight them again.

Temperature correction

This function enables to adjust the temperature settings of the electronic. If it is needed to use this function, please first contact the technical department. It is possible to adjust the temperature of the heating plate to its original settings from -30 to + 30 ° C.

Maintenance and replacement of parts

Daily maintenance

The working surface of the heating plate and the base plate have to be clean. The heating plate can be cleaned with a clean, dry cloth. Avoid the contact with the heating plate – risk of burns. The silicon gum can be cleaned with a soft cloth. You can use mild household detergent. Avoid scrub sponges, solvents or fuel. An exception can be made by replacing the silicon mat. In this case the surface of the plate has to be cleaned with acetone to remove the residuals of the old silicon foam.

Monthly maintenance

Before beginning maintenance work switch off the press, unplug it and wait until it gets cold. Some movable parts need to be greased. Greasing should be performed 2-3 times a year. You may use normal, heat resistant (up to 160°C) car grease and grease gun SM-125 (picture 1).
There are 4 points on the heat press, which have to be greased:

1. 2 points above the heating plate (picture 2).
2. 1 point by the fixation of the drive shaft. To access the point, the cover needs to be removed (picture 3).
3. 1 point by the connection piece (pictures 4-5)

After greasing, all the covers have to be reassembled.der fest. Erst danach schalten sie die Presse in.

Instruction for the replacement of the main fuse

If the heat press does not work after switching it on, but the green switch lights on, check the main fuse of the press. The main fuse 12A is placed in the bottom part of the press. To replace the fuse, switch off and unplug the heat press. Then remove the fuse bracket (picture 1). Replace the fuse and tighten the fuse bracket again (pictures 2-3).

Instruction for replacement of the silicone foam

To replace the silicon foam the press must be disconnected from the electricity and cold. For replacement you will need a new silicone foam, silicone glue and a plastic scraper to apply the silicone glue.

1. Remove the silicone foam completely with a knife. Remove the old silicon glue (you can use sandpaper).
2. Clean the plate with acetone. Clean also the surface of the new silicone foam (do not use petroleum!).
3. Apply the silicon glue on the surface of the base plate and spread it using plastic scraper.
4. Put the new mat on the even, flat surface (make sure that the side which will be glued is facing up) Then put the base plate on the foam and press it strongly (we recommend to use the bar clamps).
5. Then apply an additional portion of silicone glue along the edge of the base plate.
6. Let the glue dry for 24 hours.
7. Take off the base plate and cut off the protruding edge of the silicone foam.

Instruction for replacement of the electronics

The temperature and time of the press is controlled by the electronic devices, which is situated in the upper part of the press. The electronic devices replacement must be done by an authorized personnel after reporting the failure to the machine supplier. Switch the machine off and unplug the press. Move the heating plate to the middle position and disconnect the heating plate from the press (picture 1). Remove the upper part of the press safely (pictures 2-3) Disconnect the keyboard from the electronic device and disconnect the electronic device from the press (pictures 4-5), unscrew the fixation screw (picture 6). Take out the electronic devices (picture 7). Put the new electronic device in, connect it to the press and to the keyboard. Reassemble the press.

Instruction for the replacement of the electronics keyboard

To change the electronics keyboard the press must be switched off and unplugged. Remove the cover like in chapter 4.4. Disconnect the plug of the electronics keyboard from the electronics. Remove the keyboard from the press. Install a new keyboard and connect the plug to the electronics. Reassemble the press.

Instruction for replacement of the thermal fuse

The replacement of the thermal fuse must be done by an authorized personnel after reporting the failure to the press supplier. To replace the thermal fuse the press must be switched off, unplugged and cold. Remove the cover of the heating plate and remove the heat isolation (picture 1). Remove the thermal fuse (picture 2) and connect the new one (picture 3). Tighten it on the heating plate, put the heat isolation and tighten the cover of the heating plate again. If you use heating plate 40 x 50 cm, the same should be done with the second thermal fuse (picture 4).

Instruction for the replacement of the temperature sensor

The replacement of the temperature sensor must be done by authorized personnel after reporting the failure to the press supplier. In order to replace the temperature sensor the press must be switched off, unplugged and cold. The temperature sensor is situated directly on the heating plate. It sends reading from the heating plate temperature to the electronics. Unscrew the cover of the heating plate and remove the insulation (pictures 1-2). Unscrew the temperature sensor (pictures 3-4). Remove 2 cm of cable with nippers (picture 5). Pull of the cable isolation (pictures 6-7). Insert the wires to the ceramic block and tigthen them precisely (pictures 8-9). Lay the cables on the heat isolation. They should be situated between heat isolation and the cover (picture 10). Tighten the cover.

Fehlerbehebung

The green switch does not glow. The display does not work. The heat press is not heating.| 1. Main fuse 16A is deactivated| 1. Activate the main fuse 16A
2. The electronic device is damaged| 2. Replace the electronic device
The display shows Err. 5| Thermal fuse on the heating plate is damaged| Replace the thermal fuse. In plate 40 x 50 cm replace both thermal fuses.
The display shows Err. 1| 1. Temperature sensor is damaged or cable broken.| 1. Replace the temperature sensor
2. The heating plate is not connected| 2. Connect the heat plate to the press
The display shows Err. 2| The temperature sensor is damaged| Replace the temperature sensor
The display shows Err. 3 The display shows Err. 4| 1. Resistance of the temperature sensor is too low or too high| 1. Replace the temperature sensor
2. Failure of the electronic device| 2. Reset the electronic device. Contact the service
The display shows Err. 6 The display shows Err. 7| Relay CRYDOM is damaged| Replace the CRYDOM relay. Contact the service.
Buttons on the keyboard are not working. It is impossible to set the temperature or the time.| Electronic’s keyboard is damaged| Replace the electronic’s keyboard
---|---|---
Time does not count down after closing the heat press.| START switch is damaged| If after pushing and holding the switch START with finger, the time does not count down – replace the START switch.
The heat press heats up very slowly. One half of the plate does not reach the adjusted temperature.| One of the two heating elements is damaged| Replace the heat plate or send it for repair.
The heat press with cap plates is not heating up. Electronic device is working.| The heating elements are damaged| Replace the heating plate or send it for repair.
1. The sound is switched off| 1. Switch on the sound

E-POWERpress From 01.2020 .

| LED| ****

The heat press has an eletronic plate with six control diodes. W

In case of emergency, check which diode is lighting and compare with the table.

1 – diode is  on 0 – diode is not on

---|---|---
green| ****

yellow

| yellow| white| white| red
VCC| ****

TIMER

| HEAD| P2| P1| EMERGENCY STOP
CORRECT WORK
Start the machine, heat plate up| 1| 0| 0| 0| 1| 0
START button pushed, moving the heat plate down| ****

1

| ****

1

| ****

1

| ****

0

| ****

0

| ****

0

Heat plate downside, heating up| 1| 0| 1| 1| 0| 0
Moving the heat plate up| 1| 0| 0| 0| 0| 0
Heat plate in upper position| 1| 0| 0| 0| 1| 0

DAMAGES
problem| reason
START is switched on, no moves| 1| 1

2 sek.

| 1| 0| 1| 1| Damaged or activated EMERGENCY- STOP button

START is switched on, no moves

| ****

1

| 1

2 sek.

| ****

1

| ****

0

| ****

0

| ****

0

| Uszkodzony lub przestawiony wyłącznik krańcowy dolnej pozycji silnika (7,8)
After the START you can heat the sound of the engine, the heat plate is upside| ****

1

| ****

0

| ****

0

| ****

0

| ****

0

| ****

0

| Limiter switch for upper position is damaged or moved (9,10)

START is on, no moves

| ****

1

| ****

0

| ****

0

| ****

0

| ****

1

| ****

0

| Heat plate is not in position, limiter switch is damaged or no singla from the electronic EL1 for both-hand- control
START is switched on, heat plate moves down, the electronic is not making the countdown, the heat plate is moving immediately up after enable the START button|  | ****

Limiter switch for upper position is damaged or moved (24,25)

START is switched on, heat plate moves down, the electronic is making the countdown, the heat plate is moving immediately up after

enable the START button

|  | ****

Electronic damaged

The display of the electronic i off, no moves| 0| 0| 0| 0| 1| 0| Adapter damaged
0| 0| 0| 0| 0| 0| No power supply
START is switched on, no moves| 1| 0| 1| 0| 1| 0| Electronic ROM TIMER is damaged
START is switched on, heat plate moves down. After the countdown the plate is not moving up, constant

alarm sound is on

|  | ****

Limiter switch for upper position is damaged or moved (9,10)

Documentation

Connection diagram

Configuration of the frequency inverter

Settings of the frequency inverter OMRON SCHULZE E-Power Duo Press

• b084 – 04
• b094 – 00
• b085 – 01
• b180 – 01

Wait for the reset to complete

• A001 – 2
• F002 – 0
• F003 – 0
• b012 – 3,47
• F001 – 50
• A044 – 01
• A045 – 83

d001 confirm and leave at this setting

Warranty terms and conditions

Schulze heat presses and machines used for screen printing have a warranty for 24 months. This warranty includes the whole construction of the machine, mechanical elements, electronic device and covers. Expandable parts, fuses and safety covers are not included in the warranty terms. Thermo fuses, temperature sensor, switches and buttons and all springs in the machines have a warranty for 6 months. Heating elements for mug presses have a warranty for 6 months or 500 pressing procedures.
Warranty does not cover:

1. Components which have been damaged by external factors such as water, electrostatic discharge and others.
2. Components and parts which have been damaged as a result of using unsuitable consumables.
3. Repairing damage caused by improper transport or use not in accordance with the operating conditions specified in this manual, caused by the fault or ignorance of the buyer.
4. Wear and tear, damage to consumables such as Teflon tape, silicone foam, air cushion in membrane plates, lamps, glass.
5. Warranty rights do not include the purchaser’s right to claim reimbursement of lost profits and costs incurred as a result of equipment failure.

Conformance declaration

Manufacturer ROMANIK Andrzej Romanik ul. Przemysłowa 10 84 – 240 Reda, Poland hereby declares that the following machine: Heat press SCHULZE E-Power Duo Press is compliant with the specifications of the followings EC directives:

• Machinery (2006/42/EC)
• Low Voltage (2014/35/EU)
• EMC (2014/30/EU)
• RoHS II (2011/65/EU) and RoHS III (2015/863)

used norms and technical specifications:

• PN-EN ISO 12100:2012
• PN-EN 60204-1:2018-12
• PN-EN 61000-6-1:2019-03
• PN-EN 61000-6-3:2008/A1:2012
• PN-EN ISO 13850:2016-03
• PN-EN IEC 6300:2019-01
• Applied quality system: testing report / 2021
• Reda, 21.05.2021 r.

Company owner: Andrzej Romanik

Manufacturer:

• Romanik Andrzej Romanik ul. Przemysłowa 10 84-240 Reda

Polen

• Distributor and representative: Walter Schulze GmbH Sarirstraße 5 12529 Schönefeld

Deutschland

• www.schulzeshop.com

Entity authorized to prepare technical documentation and declaration of conformity: ROMANIK Andrzej Romanik ul. Przemysłowa 10, 84-240 Reda, tel. 58 6780-700, e-mail: sprzedaz@romanik.pl The manufacturer reserves the right to make constructional and technological changes.

References

• Werbetechnik Shop - Textildruck Großhandel | Gröner-Schulze GmbH

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>