Ecowell EHT200 Tower Heater User Manual

: June 15, 2024
: Ecowell

Table of Contents

IMPORTANT SAFETY INSTRUCTIONS
SAFETY PROTECTION FEATURE
CAUTIONS
TECHNICAL PARAMETERS
USAGE
MAINTENANCE
WARRANTY
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

**Ecowell EHT200 Tower Heater User Manual

**

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons.

WARNING: POTENTIAL ELECTRICAL HAZARD IF NOT ADHERED TO

This heater must be plugged into a 120V, 15amp (or more) circuit of its own. Do not plug anything else into the same circuit. If unsure if your home meets this specification, consult a certified electrician before use. Risk of fire, overheating, malfunction, property damage, injury or even death may result if not adhered tol
Plug the heater on a properly grounded outlet only. Do not plug it on extension cords, surge protectors, timers, direct breakers, or an outlet with other appliances connected to the same outlet. There are risks of fire, overheating, malfunction, property damage, injury, or even death that may result if not adhered to!
The heater surface in hot when in use. To avoid burns, do not touch the heater surfaces with your hands.
Keep the combustible materials (fumiture, pillows, bedding, papers, clothes, and curtains) at least 3ft. from the front of the heater and keep them away from the sides and back of the heater
Extreme caution is necessary when the heater is used by children, invalids, pets, or the heater is left operating unattended.
Always unplug the heater when not in use.
Do not use the heater with any damage, such as a worn cord or plug, or any heater with malfunctions after been dropped. Please contact the seller for resolution options
Do not use the heater outdoors. Exposure to outdoor elements such as rain, snow sun, wind, or any extreme temperatures may cause a safety hazard.
This heater is not intended for use in bathrooms, laundry areas, ar moisture indoor locations, or any extended outlets.
Never place the heater where it may fall into a bathtub or other water receptacles.
Do not run the cord under the carpet. Do not cover the cord with throw rugs, runners, or similar coverings. Arrange the cord away from traffic areas and where it will not be tripped over.
The heater must be plugged into a wall outlet that is a dedicated circuit with a minimum 15amp rating on that individual circuit.
To disconnect the heater, first, switch the power button to the OFF status, then you can remove the plug from the wall outlet.
Do not let any objects enter or block any ventilation or exhaust opening as this may cause electric shock, fire, or damage the heater.
Leave at least 3 ft. of unobstructed space to the front and rear of the heater to allow for maximum heat, air, and ventilation flow.
Inner parts of the heater might slightly hot arcing or sparking. Do not use it in areas 0
where gasoline, paint, or flammable liquids are used or stored, nor use flammable solvents to clean the heater. Keep the heater dry at all times.
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
Do not use abrasive solvents to clean the heater, in case it causes any damage to the finish or casing.
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use it on any soft surfaces, like a bed or carpet where the opening may become blocked.
Always plug heaters directly into a wall outlet/receptacle. Never use an extension cond or relocatable power tap (outlet/power strip).
Do not unplug the heater when the unit is still ON, as the vent grill will be hot.
Shut off the switch of the heater and wait 10 minutes before unplugging from the wall.

SAFETY PROTECTION FEATURE

Overheating Protection

This heater is equipped with an overheat safety feature. When the intemal components of the heater reach a certain temperature that could cause overheating or possible fire, the heater will automatically shut off.
if the heater has been overheated, you will need to unplug the heater from the wall and re-plug it to use the heater again.

Tip-Over Protection

This heater is equipped with a tip-over switch on the bottom. When the heater is tited of the base is off the ground, the heater will automatically shut down. We recommend that you place the heater on a flat floor or desk, and do not put it on an uneven carpet which may trigger the tip over switch.

Thermostat Function

This heater is equipped with a thermostat, which allows you to control the temperature. It will get the heater automatically adjust according to your Set temperature and the environment temperature. For example, if the Environment temperature is 82℉ : a. When the Set temperature(80 ℉ ) is equal to or lower than the Environment temperature, the appliance will stop heating and turn to fan mode.

b. When the Set temperature(85℉) is higher than the Environment temperature, the appliance will turn to low heat mode.
c. When the Set temperature(90℉) is higher or equal to the Environment temperature+5℉ or +6℉ , the appliance will turn to high heat mode. Note: ℉ display will be ± 1℉ deviation.

CAUTIONS

WARNING: To prevent electrical shock, match the wide blade of the plug to the wide slot of the receptacle and fully insert.

WARNING : It is normal for the power cord to get hot at work.
However, a poor connection or loose fit between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified electrician to inspect the original outlet for damage.

TECHNICAL PARAMETERS

Model	Rated Power	Rated Voltage	Frequency
EHT200	1500W	120V	60Hz

USAGE

Please check before you use:
a. The heating element and electric wire are NOT broken.
b. Please do not use the socket lower than 15A for fear of any accident.
Use the fan heater in the flat place to avoid being toppled.
If you stop using the heater, turn off the power switch, then put off the plug.
If you want to move the heater, please turn off the switches, then put off the plug.

USING METHODS

EHT200 Turn on the power switch in the back first， “O”= OFF，“—”ON；

Turn on the power switch in the back, LED display “–”, the appliance is standby; See picture 1.1
Press “ ” as follows: ON (only Fan working), LED display Environment temperature(default is ℉ after the power cut off); OFF(Fan will keep working for 30 seconds when shutdown the appliance after heating); See picture 2.1.
Press “ ”, low heat(1000W), high heat(1500W), FAN working; See picture 3.1-3.2
Press “ ” to set a timer, 1h、2h…..12h; See picture 4.1-4.4
Press “ ”, SWING ON, SWING OFF; See picture 5.1
Press “ ” to set temperature, Temperature range: 50-
95 ℉ ; see picture 6.1-6.2 Press over 3s, switch to ℃ , Temperature range: 10-35 ℃ ; See picture 6.3-6.4.
Press over 3s again, switch to ℉ . (The remote control can not switch the Temperature unit, only can switch on the machine.)
The operation method of the remote control is the same.

Note: The indicator lights when the corresponding function is working.

| | | |
---|---|---|---|---
| | | |
| | | —| —

MAINTENANCE

Please make sure the plug should be pulled out BEFORE cleaning the heater.
Strictly prohibit washing the radiator by water, it can be cleaned by a piece of soft damp cloth with a little neutral detergent. Please do not use other solvents like gasoline.
The fan heater must be used or stored after cooled and dried completely.
If stop using the heater, please pull out the plug from the socket, and store it in the dry place with a rust-proof polybag, original packing is favored.

WARRANTY

ALTON INDUSTRY LTD. GROUP 2-YEAR LIMITED WARRANTY
This warranty covers any defects in materials or workmanship of the endorsed product. Alton Industry Ltd. Group will repair or replace any defective materials due to craftsmanship of the product. This warranty does not cover any problem caused by misuse, abuse, accidents or acts of God, such as floods or hurricanes. Consequential and incidental damages are not covered under this warranty. Coverage terminates if you sell or otherwise transfer the ownership. If you feel you have a defective product, please submit a copy of your receipt to the address below and call 1-888-899-0146 for instructions prior returning this item to the store or sending back to:

Alton Industry Ltd. Group 643 Innovation Drive West Chicago, IL 60185

We will inspect the product and contact you within 72 hours to give you the results of our inspection. We reserve the right to repair or replace the product at our discretion. However, we may replace the product with one of similar but not exact features. Parts and Service Information available call Alton Industry at 1-888-899-0146. This warranty gives you specific legal rights. You may have other rights which vary from state to state.

USER MANUAL
Please read this user manual carefully before using your ptc heater, so that you can use it correctly.

ALTON INDUSTRY LTD. GROUP
643 Innovation Drive, West Chicago, IL, 60185

https://www.altonindustries.com

info@altonindustries.com

Made in China