PARIS RHONE PE-AH033 TOP Fill Ultrasonic Cool Mist Humidifier User Manual

PARIS RHONE PE-AH033 TOP Fill Ultrasonic Cool Mist Humidifier User Manual

Safety Instructions

Warning: Please be aware of the following points otherwise you might in danger if high voltage charges or but your body.

1. Never disassembly the base unit without consult qualified personnel.
2. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
3. Do not change attachment without definite permit from our company otherwise you might catch hazard.
4. Any abnormal smell during normal operation, please switch off and disconnect power supply and want qualified personnel amend.
5. Always trun off or unplug before removing, filling or emptying the water tank.
6. Keep detergents, chemical solutions away children.
7. Cleaning with clear water when detergents & chemical solutions splash into mouth & eyes, consulting doctors against serious hazard.
8. Never touch water in the Water Tank & components in the water when the unit is in working.
9. Never switch on when there is no water in the water tank.
10. Never scrape Ultrasonic Atomizing Transducer at will.
11. Never clean Ultrasonic Atomizing Transducer with detergents, chemical solutions, etc. 12) Never let water splash into inner Base Unit when cleaning for avoiding components damage.
12. Never move the machine with the full water tank.
13. Posit the unit on the even surface and keep the machine at least 2 meters far away from the furniture and the other electrical appliances.
14. Care should be taken due to emission of hot vapor.
15. This appliance is not intended for use by persons (including children) with reduced physical. sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety
16. Children should be supervised to ensure that they do not play with the appliance.
17. Only use water in the tank, never use any additive such as essential oils, etc. into the tank.

Specifications

Operation Instruction

• Use clear water not over 40 °C.
• Check the water basin, make sure it is clear.

Operation steps:

1. Take the water tank cap out of the base, revolve the tank-cap by the directions of UNLOCK and LOCK, and fill the water tank with clear water. Close the tank-cap.

2. Put the nozzle into the socket on top of the humidifier.

3. Connect the adapter, switch on the unit (NEVER RUN THE UNIT WHEN THERE IS NO WATER IN WATER TANK), the LED display will on for 2 seconds then be off. The unit stands by.

4. Press Power Button, the power indicator will light up white, indicating the humidifier has been turned on (medium mist level). Press again to turn it off.

5. When the unit is on, press the Mist Button to adjust the mist among Low / Medium / High  levels.

6. When the mist is on, press the Timer Button to cycle through 2 H4H8H.

7. When the unit stands by or turns on:

8. Press the Night Light Button / Sleep Button once to turn on the night light in water tank.

9. Press it again to turn off the night light in water tank.
   When the unit turns on:

10. Hold the button for 3 seconds to enter sleep mode, All the indicators are off. Press any button to activate Sleep mode. All the other buttons remain functional.

11. Hold the button for 3 seconds again to exit sleep mode.

12. When there is no enough water inside the water tank under Sleep Mode, the humidifier will turn off automatically.

Low Water Protection.

When there is not enough water inside the water tank, the humidifier will stop misting and Low Water Protection will be activated (Waterless lamp flashes in red with BEEP sound for 3 times). Then the humidifier will turn off automatically. It is designed for safety to prevent the humidifier from possibly overheating and damaging the atomizer.

Troubleshooting

Adjust the mist output
Bad smell mist| New unit| Take out water tank, open cover,let   it stays 12 hours   in coolposition
Dirty water or residue water| Cleaning water tank, fill in clearwater
Mist fog is too small| Too much scale in the waterbasin| Clean transducer
Dirty water or residue water| Clean water tank,  change tofresh clear water
Water is too cold| Add some warm water inside
Abnormal noise| Resonant in water tank whenwater is too lower| Fill water tank with water
Unit is on a unstable surface| Move the unit to a stable flatsurface
Mist coming out around thenozzle| There are apertures between thenozzle and water tank| Dip the nozzle in water for awhile and then fix it to the socketon water tank

Maintenance

We recommend:

1. Use cold boiled water or distilled water.
2. Clean the transducer, water tank and main unit every week.
3. Change the water in water tank more often to keep it fresh.
4. Make sure to pull out the water from the water tank and dry the whole unit before you idle the unit for a long period of time.
5. Do not use the chemical for cleaning.

How to clean the transducer:

1. Put 5-10 drops of plain white vinegar on the surface of the transducer, wait for 2-5 minutes;
2. Brush out the scale on the surface.
3. Rinse the transducer with clean water.

How to clean the basin unit:

• Cleaning the water basin with soft cloth and cleaning detergent if there is scale in it.
• If the scale is covered on the security switch, drop the plain white vinegar on the scale and clean it out with the brush..
• Rinsing the water basin with clean water.

DISPOSAL: Do not dispose this product as unsorted municipal waste, collection of such waste separately for special treatment is necessary.

**** Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Email: [email protected]
Manufacturer: Shenzhen Danya Technology Co.,Ltd.
Address: Room 3323, Building E, Galaxy World Phase II, Minle Community,
MinZhi Street, Longhua District, Shenzhen, China
Made in China

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>