BUTURE Beta02 Jump Starter User Manual
- June 15, 2024
- BUTURE
Table of Contents
BUTURE Beta02 Jump Starter
PACKING LIST
KNOW YOUR BETA02
Thanks for choosing the BUTURE Beta02 jump starter! Please read all instructions carefully before using this product and keep these instructions for easy reference.
SPECIFICATIONS
OPERATION GUIDE
Before use, please note
- Charger not included. A universal USB charger is fine, such as your phone charger (2A above is suggested).
- When using the product for the first time, please make sure it is fully charged.
- It is recommended to charge up the product every 3 months to prolong its lifespan even if the unit has not been used.
Recharge the Jump Starter
Step 1. Connect the jump starter to the power supply via the USB-C
charging cable.
Step 2. Disconnect the power after it is fully charged.
Tip: Do not charge the jump starter unit immediately after starting the
engines, but at least 30 minutes later.
Charge Your USB Devices
Step 1. Plug the Charging Cable to electronic devices with USB output.
Step 2. Press the power button to start charging. Disconnect when
charging is not required.
LED Flashlight
Press the switch button for 3 seconds to start the LED light and short press
to switch to SOS, strobe and off in order.
Start Vehicles
Before use, please note:
- This product is only suitable for 12V vehicles
- Before starting your car, please make sure that the remaining power is not less than 80%. Fully charged is suggested.
Step 1.
Insert the clamp plug completely into the product.
Step 2. Connect the RED clamp to the vehicle’s battery positive (+)
terminal and connect the BLACK clamp to the vehicle’s battery negative (-)
terminal.
Step 3. Start the vehicle and the interval time between each starting
must be OVER 60
Step 4. When the vehicle is started, remove the jumper cable from the
jump starter and disconnect the red and black clamps from the vehicle battery
terminals within 30 seconds.
Tip: If 3 attempts fail, please check if there are problems with the
vehicle engine or circuit, meanwhile, check the jump starter. If problem,
please contact us at support@ibuture.com.
INDICATOR AND TROUBLESHOOTING
In any of the following situations, the smart clamp will turn mentation.
IMPORTANT SAFETY WARNING
ATTENTION
Please read the following safety warning before using the product and take
safety protection measures to avoid malfunctions caused by accidental
operation.
Personal Safety
- Store in a cool and well-ventilated place out of reach of children and pets.
- Do not place the product in high temperature environment for a long time. The operation temperature of this product is -20~60°C. The storage temperature should not exceed 50°C /122 °F.
Electrical Safety
- Only start vehicles with the smart jumper cable supplied by the manufacturer.
- Do not use the product if the clamp or cable is damaged.
- Do not connect the red and black clamps when the product is outputting.
- Do not connect the red and black clamps to the same piece of metal.
- Do not disassemble or modify this product.
- Do not use detergent to clean this product.
- Do not abuse this product and avoid heavy dropping or repeatedly hitting it.
- Do not operate the product in explosive environments such as flammable liquids, gases or dusts.
- Do not immerse the product in water.
Battery Safety
- Do not litter the product and it should be safely recycled.
- Do not incinerate the product or be exposed to high temperatures, as they may explode.
- Only use replacement parts or accessories provided or recommended by the manufacturer.
WARRANTY
Our company provides customers with a warranty of 24 months from the date of
purchase.
For assistance or warranty cover claim, please contact us: Email:
support@ibuture.com
Correct Disposal of this produc t
This marking indicates that this product should not be disposed of with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmentally safe recycling.
Federal Communication Commission Interference Statement
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used by the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
Declaration of Conformity
We (The manufacturer responsible for this declaration) Ekoo Electronic Co.,
Ltd. (Company name) B09, block B,f2, bldg.b, running Pioneer Park, no.973,
Mini Avenue, Minzhi St., Longhua, Shenzhen, CN (Company address) declare under
our sole responsibility that the product Trade name: BUTURE Equipment: Jump
Starter with Air Compressor Model No. : Beta 02 to which this declaration
relates conforms with the essential requirement set out in the Council
Directive on the Approximation of the laws of the Member States relating to
the LVD Directive(2014/35/EU) & EMC Directive(2014/30/EU) & RoHS(2011/65/EU)
product is responsible for affixing CE marking, thefollowing standards were
applied:
- EN 62133-2:2017
- EN 55032:2015+A11:2020
- EN 55035:2017+A11:2020
- IEC62321-3-1:2013
- IEC62321-4:2013
- IEC62321-5:2013
- IEC62321-6:2015
- IEC62321-7-1:2015
- IEC62321-7-2:2017
- IEC62321-8:2017
Full Name: George.wang Position: Approbation Manager
Signature: Gange.wag Place/Date: Shenzhen, China/Aug.8-2022
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>