Tractel 1t Corso Beam Clamp Instruction Manual

Tractel 1t Corso Beam Clamp

Product Information

Specifications

• Product Name: Corso Beam Clamps
• Usage: Lifting accessory for anchoring a hoist or winch to an overhead I beam
• Design: Simple design, easy to install
• Operation: Manual operation only, not motorized
• Working Load Limit : Do not exceed the specified working load limit
• Restrictions: Not to be used for lifting people or in explosive atmospheres

Description of Equipment
The corso beam clamp consists of the following components:

1. Side plates
2. Adjustable screw
3. Anchor point

Rigging Arrangements
The beam clamp is anchored to a fixed point on the overhead I beam. The appropriate beam clamp should be selected based on theload to be lifted, and the capacity of the beam should be calculated by a qualified person.

Installation

1. Unscrew the adjustable screw to open the clamp wider than the beam.
2. Fit the clamp onto the beam, ensuring it is held in place without jamming.
3. Screw up the adjustable screw until it touches the beam, then manually tighten the screw.
4. Ensure that the clamp is in contact with the beam at points A1, A2, B1, and B2. There should be no other contact between the clamp and the beam.

Anchoring
The hoist or winch should be anchored to the beam clamp using the provided anchor point. It is important not to anchor any load, hoist, or object to any component of the clamp other than the anchor point.

Operation
The corso beam clamps are designed for static use. It is crucial to never attempt to move a beam clamp under load. Moving the position of the beam clamps should only be carried out by a qualified person.

FAQ

• Can the corso beam clamps be used for lifting people?
  No, the clamps described in the manual must not be used for lifting people.

• Can the corso beam clamps be motorized?
  No, these clamps are designed for manual operation and must not be motorized.

• Can the corso clamps be used in explosive atmospheres?
  No, corso clamps must not be used in explosive atmospheres.

• How should I calculate the capacity of the beam?
  The capacity of the beam should be calculated by a qualified person based on the load to be lifted.

• Can I dismantle or alter the machine by myself?
  No, the manufacturer declines any responsibility for the consequences of dismantling or altering the machine by any unauthorized person. Specifically excluded is the replacement of original parts by parts of another manufacturer.

• Where can I get extra copies of the manual?
  Extra copies of this manual will be supplied on request.

INTRODUCTION

• Always concerned with improving the quality of its products, the TRACTEL® reserves the right to modify the specifications of the equipment described in this manual.
• The companies of the TRACTEL® and their agents or distributors will supply on request descriptive documentation on the full range of TRACTEL® products: lifting and pulling machines, permanent and temporary access equipment, safety devices, electronic load indicators, accessories such as pulley blocks, hooks, slings, ground anchors, etc

GENERAL WARNING

1. Before using the clamp, it is essential for the safe and correct operation of the equipment that this manual be read and fully understood and that all the instructions be followed. This manual should be made available to every operator. Extra copies of this manual will be supplied on request.
2. The corso clamp allows the operator to carry out work with complete safety. Ensure that this clamp is only handed over for use or rigging to an operator who is trained to operate it in a responsible manner.
3. Never use a clamp which is not in good working condition. Continous monitoring of the condition of the machine is an important safety consideration.
4. The manufacturer declines any responsibility for the consequences of dismantling or altering the machine by any unauthorized person. Specifically excluded is the replacement of original parts by parts of another manufacturer.
5. The clamps described in this manual must not be used for lifting people.
6. Morever, these clamps are designed for manual operation and must not be motorized.
7. Never apply or attempt to apply to the machine a load or effort greater than the working load limit.
8. Corso clamps must not be used in explosive atmospheres.
9. The installation of a corso clamp on an overhead metal beam requires a strength calculation to be carried out by a qualified person.

DESCRIPTION OF EQUIPMENT

1. Side plates,
2. Adjustable screw,
3. Anchor point.
   The corso beam clamp is a lifting accessory. It has been designed for anchoring a hoist or winch to a fixed point on an overhead “I” beam (Fig. 2),
   The corso beam clamp is of simple design and easy to install. Once fitted correctly, it may be used with complete safety.

RIGGING ARRANGEMENTS

The beam clamp is anchored to a fixed point on the beam (Fig. 2).
NB: The beam clamp must be appropriate for the load to be lifted and consequently the capacity of the beam should be calculated by a qualified person.

INSTALLATION

1. Unscrew the adjustable screw to open the clamp wider than the beam.
2. Fit the clamp onto the beam. The clamp should be held in place without jamming on the beam.
3. Screw up the adjustable screw until it touches the beam. Tighten the screw manually.
4. Ensure that the clamp is in contact with the beam at points A1, A2, B1 and B2. There should be no other contact between the clamp and the beam (see Fig. 1).

ANCHORING

The hoist or winch should be anchored to the beam clamp by the anchor point provided.
WARNING: a load, hoist or any other object should not be anchored to any component of the clamp, other than the anchor point.

OPERATION

Corso beam clamps are designed for static use. Never attempt to move a beam clamp under load. Moving the position of the beam clamps should only be carried out by a qualified person.

TAKING OUT OF SERVICE AND STORAGE

• Before taking a corso out of service, that is removing it from the beam to which it is attached, ensure that there is no load on the beam clamp or the trolley, by removing the sling, hoist or winch.
• Unscrew the adjustable screw until the beam clamp is opened sufficiently to be removed from the beam.

MAINTENANCE

Corso beam clamps should be regularly cleaned and oiled.

WARNINGS AGAINST HAZARDOUS OPERATION

The use of corso beam clamps, in accordance with the instructions in this manual, is a guarantee of safety. Neverthless, it is useful to draw the attention of users to the following warnings:

• Never use corso beam clamps or trolleys for lifting people under any circumstances.
• Never use corso units beyond their working loadlimit.
• Never use corso units for applications other than those for which they are intended.
• Never fit a corso unit to a beam by any means other than those described in this manual.
• Never attach loads to parts of corso units other than the anchor point provided.
• Never lift a load which is not aligned with the clamp as described in this manual.
• Never allow a load attached to corso to swing or spin.
• Never walk or stand under the suspended load.

TROUBLESHOOTING

If the adjustable screw is difficult to turn or is blocked, it indicates that the thread has been damaged. In this case, return the beam clamp to an approved TRACTEL® repairer.

HEALTH AND SAFETY AT WORK

It is the responsability of every company to ensure that its employees have been fully and properly trained in the safe operation of the equipment.

Markings

A nameplate is riveted to each Corso™ clamp (fig. 3), containing the following information:

• item 1: Clamp name

• item 2: Working Load Limit (WLL) in t.

• item 3: Beam width

• item 4: CE Marking

• item 5: Year of manufacture

• item 6: Clamp model,

• item 7: Manufacturer’s address and
  contact details:

  • TRACTEL SAS
  • RD 619 Saint-Hilaire- sous-Romilly
  • BP38 – F-10102 FRANCE

• item 8: Serial No.,

• item 9: Symbol indicating that you must read this manual before using the clamp

DIMENSION

ECLARATION OF CONFORMITY

CERTIFIES THAT:
The equipment designated oppo-site is compliant with the technical safety rules appli-cable on the initial date of marketing in the EUROPEEN UNION by the manufacturer.
MEASURES APPLIED: See below

DESIGNATION
Fastening clamp for mounting on structural sections

APPLICATION
Hoisting accessories

MAKE

TYPE

INSPECTION

ABOUT COMPANY

• TRACTEL S.A.S.
  • RD 619 Saint-Hilaire-sous-Romilly, B.P. 38
  • F-10102 ROMILLY-SUR-SEINE
  • T : 33 3 25 21 07 00
  • Fax : 33 3 25 21 07 11
• TRACTEL SECALT S.A.
  • P.O. Box 75, L-4001 Esch-sur-Alzette
  • Rue de l’Industrie, L-3895 FOETZ
  • T: 352 43 42 42 1
  • Fax: 352 43 42 42 200
• TRACTEL GREIFZUG GmbH
  • Scheidtbachstrasse 19-21
  • D-51469 BERGISCH-GLADBACH
  • T: 49 2202 10 04 0
  • Fax: 49 2202 10 04 70
• TRACTEL UK LTD
  • Old Lane, Halfway
  • SHEFFIELD S20 3GA
  • T: 44 114 248 22 66
  • Fax: 44 114 247 33 50
• TRACTEL IBÉRICA S.A.
  • Carretera del medio 265
  • E-08907 L’HOSPITALET (Barcelona)
  • T: 34 93 335 11 00
  • Fax: 34 93 336 39 16
• TRACTEL ITALIANA S.p.A.
  • Viale Europa 50
  • I-20093 Cologno Monzese (MI)
  • T: 39 02 254 47 86
  • Fax: 39 02 254 71 39
• TRACTEL BENELUX B.V.
  • Paardeweide 38
  • NL-4824 EH BREDA
  • T: 31 76 54 35 135
  • Fax: 31 76 54 35 136
• LUSOTRACTEL LDA
  • Alto Do Outeiro Armazém 1 Trajouce
  • P-2785-086 S. DOMINGOS DE RANA
  • T: 351 214 459 800
  • Fax: 351 214 459.809
• TRACTEL POLSKA Sp. Zo. o
  • ul. Bysławska 82
  • 04-993 Warszawa
  • T: 22 616 42 44
  • Fax: 22 616 42 47
• TRACTEL CHINA LTD
  • 3rd Floor, Block B, Workshop 3,
  • N° 255 Cai Lun Road
  • Zhang Jiang Hi tech Park, Pudong New Area
  • Shanghai 201203 People’s Republic of China
  • T: +86 (0) 21 6322 5570
  • Fax: +86 (0) 21 5353 0982
• TRACTEL SINGAPORE Plc
  • 50 Woodlands Industrial Parc E7
  • Singapore 75 78 24
  • T: 65 675 73113
  • Fax: 65 675 73003
• TRACTEL MIDDLE EAST
  • P.O. Box 25768
  • DUBAI
  • T: 971 4 34 30 703
  • Fax: 971 4 34 30 712
• TRACTEL RUSSIA O.O.O.
  • uI. Petrovka, 27
  • Moscow 107031
  • Russia
  • Tel/Fax: +7 495 989 5135
• TRACTEL MEXICO SA de CV
  • Galileo N° 20, despacho 504, Colonia Polanco,
  • delegació Miguel Hidalgo
  • CP 11560 México, DF
  • Oficina Mexico: 01 55 67 21 87 18 y 19
  • Office & Fax: 01 55 67 21 87 18

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>