UrRider Child Bike Seat Installation Guide
- June 15, 2024
- UrRider
Table of Contents
UrRider Child Bike Seat
Product Information
Specifications
- Product Name: Child Bike Seat
- Installation Method: Front Support Module, Rear Pipe Clamp Module
- Email for Customer Service : urrider8@hotmail.com
Product Usage Instructions
Installation Procedure
- Front Support Module:
- Place the front support module in the desired position on the bicycle.
- Press down the eccentric quick-release handle to lock it in place.
- Rear Pipe Clamp Module:
- Attach the seat post clamp base onto the bicycle seat post.
- Wrap the hinge around the seat post clamp base.
- Tighten the ball head nut completely.
- Press down the handle, ensuring that the plastic pad is positioned between the hinge and the handle.
- If the handle is too loose or too tight, adjust the ball head nut accordingly and re-press the handle.
Frequently Asked Questions (FAQ)
1. The front part of the seat cannot be installed, and both the armrest and support arm shake significantly. The limit stop cannot be buckled?
This situation usually occurs when the front handle (eccentric quick-release handle) has not been pressed down. Follow these steps to resolve the issue:
- Adjust the angle of the armrest and the front support arm.
- Re-press the front handle to securely lock the seat in place. The limit stop is responsible for synchronizing the adjustment angles of the left and right front support arms. If it is obstructed by the car beam, there is no need to buckle it, as it will not affect the use of the child seat.
2. After installation, is there still a wobble in the rear seat?
If the entire seat wobbles noticeably, it may be due to the clamp module not being tightly locked or an incorrect installation order. Follow these steps to resolve the issue:
- Open the quick-release handle.
- Tighten the ball head nut.
- Re-fasten the quick-release handle.
Ensure that the front cushion of the seat is snug against the front beam of the bicycle, forming a 2-point support. Do not install with only a single point hanging in the air.
APPLICABLE BICYCLE TYPES AND SIZE REQUIREMENTS:
Mountain-style child seats are suitable for mountain bikes and hybrid bikes that meet the following criteria:
- A: Seat post diameter is 2.5-3.5c m (circular or elliptical)
- B: Top tube width is ≤5.5cm (no cables on the top tube)
- C: Horizontal distance from seat post to top tube is > 39cm
- D: The top tube is inclined (not horizontal)
Textual Seat Installation Procedure
Front Support Module
First, adjust the angle of the armrest and the front support arm (the armrest is generally in a vertical position, and the support arm is greater than 90°). Ensure the rubber pad at the bottom of the armrest base is in contact with the bicycle’s front beam for proper force distribution. Secure the stainless steel stopper plate (if it’s obstructed by the bike beam, you can leave it out), then press down on the handle. (the eccentric quick-release handle is for pressing to lock, not for twisting to tighten.)
Rear Pipe Clamp Module
The seat post clamp base fits onto the bicycle seat post, and after closing, the hinge wraps around it. Tighten the ball head nut completely and then press down the handle. (Note that the position of the plastic pad is between the hinge and the handle.) If the handle is pressed too loosely or too tightly, adjust the ball head nut appropriately and then re-press the handle.
Installation FAQ Guide
1. The front part of the seat cannot be installed, and both the armrest and support arm shake significantly. The limit stop cannot be buckled?
Usually, this situation is because the front handle (eccentric quick-release handle is for pressing and locking, not for rotating and tightening) has not been pressed down. Adjust the angle of the armrest and the front support arm, and then re-press the front handle. The function of the limit stop is to synchronize the adjustment angles of the left and right front support arms. If it is obstructed by the car beam, the limit stop does not need to be buckled, which will not affect the use of the child seat.
2. After installation, is there still a wobble in the rear seat?
If the entire seat has a noticeable wobble, the clamp module is not tightly locked. It could be due to the incorrect order of installation. Correct installation order: Install the front support module first, followed by the rear clamp module. Adjustment method: Open the quick-release handle, then tighten the ball head nut and re-fasten the quick-release handle. (Make sure the front cushion of the seat is snug against the front beam of the bicycle, forming a 2-point support. Do not install with only a single point hanging in the air.)
3. Children riding in child seats might experience the seat touching their backs.
A few bicycle saddles are relatively narrow and long, which can lead to the child seat touching the child’s back after installation. It’s recommended to move the bicycle saddle backward by 2-3CM to avoid this issue.
Child Bike Seat Installation Guide
- Thank you for purchasing our product.
- Please scan the QR code to watch the installation video!
- Do you have any after-sales issues?
- Please contact our customer service promptly: urrider8@hotmail.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>