Metra 95-7603 Dash Kit Instruction Manual

Metra 95-7603 Dash Kit

KIT FEATURES

• ISO DDIN radio provision

KIT COMPONENTS

• A) ISO DDIN trim plate

WIRING & ANTENNA CONNECTIONS (sold separately)

• Wiring Harness:  70-7552
• Antenna Adapter:  40-NI12

TOOLS REQUIRED

• Panel removal tool
• Phillips screwdriver

CAUTION! All accessories, switches, climate control panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

Using Instructions

Nissan Versa 2007-2011

1. Unclip and remove the panel above the radio. (Figures A and B)
2. Unclip and remove the entire trim panel surrounding the radio and A/C controls. (Figure C)
3. Remove (4) Phillips screws securing the radio. (Figure D) Continue to kit assembly

Nissan Versa S, Versa S+, Versa / SV (base) 2014, Versa 2012-2013

1. Unclip and remove the entire panel surrounding the radio including the A/C vents. (Figure A)
2. Remove (4) Phillips screws securing the radio. (Figure B) Continue to kit assembly

Nissan Juke 2011-2014

1. Unclip and remove the climate control panel. (Figure A)
2. Remove (2) Phillips screws securing the radio trim panel. (Figure B)
3. Remove (4) Philips screws securing the radio. (Figure C) Continue to kit assembly

Nissan Rogue 2011, Rogue S 2012-2013, Rogue SV (with SL package) 2012-2013, Rogue Select (with lower model radio) 2014-2015

1. If equipped with a centre speaker: Unclip and remove the grille then remove (4) Phillips screws to remove the speaker. (Figure A)
2. Unclip and remove the panel below the radio including the A/C controls. (Figure B)
3. Unclip the radio trim including the A/C vents then unplug the hazard switch and remove the panel. (Figure C)
4. Remove (4) Phillips screws securing the radio. (Figure D) Continue to kit assembly.

Chevrolet City Express (without NAV) 2015-up Nissan Cube 2009-2014 Nissan NV200 (without NAV) 2013-up

1. Unclip and remove the recirculate/ fresh slide button. (Figure A)
2. Unclip and remove the entire panel surrounding the radio including the a/c vents. (Figure B)
3. Remove (4) Phillips screws securing the radio. (Figure C)

Nissan NV 2012-2014, Nissan NV (without NAV) 2015-up

1. Unclip and remove the A/C vent to the right side of the factory radio. (Figures A)
2. Remove the (2) Phillips screws exposed behind the vent on the radio trim panel. (Figure B)
3. Unclip and remove the left A/C vent next to the instrument display. (Figure C)
4. Unclip the top edge of the knee bolster panel below the steering column and let hang. (Figure D)
5. Unclip the circle trim around the key cylinder.
6. Unclip and remove the gauge cluster trim panel. (Figures E)
7. Remove (2) Phillips screws exposed behind the panel on the left side of the radio trim panel. (Figure F)
8. Unclip and remove the trim panel surrounding the factory radio. (Figure G)
9. Remove (4) Phillips screws securing the radio. (Figure H)

Nissan Quest (without NAV or rear seat entertainment) 2011-2012

1. Unclip and remove the panels from the bottom left and right side of the centre console. (Figure A)

2. Remove (2) clips per side exposed behind lower panels. (Figure B)

3. Unclip and pull the centre console toward the rear of the vehicle. (Figure C)
   Note: You do not have to fully remove the console.

4. Unclip and remove the trim panel to the left of the shifter housing the start/stop button. (Figure D)

5. Unclip and remove the panel on the end of the passenger side of the dash. (Figures E)

6. Remove (1) Phillips screw from the trim panel above the glove box then unclip and remove the panel. (Figure F)

7. Remove (1) Phillips screw from the cup holder panel then unclip and remove the panel. (Figure G)

8. Remove (2) Phillips screws from the A/C control panel and unclip and let hang. (Figure H)

9. Remove (2) Phillips screws from the bottom of the radio trim panel including the vents then unclip and remove the panel. (Figure H)

10. Remove (4) Phillips screws securing the radio. (Figure I)

ISO DDIN radio provision

1. Remove the brackets from the factory radio.
2. Secure the brackets to the aftermarket radio using the screws supplied with the aftermarket radio. (Figure A)
3. Locate the factory wiring harness and antenna connector in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS.
4. Place the ISO DDIN trim plate on the front of the radio. (Figure B)
5. Reassemble the dash in reverse order of disassembly.

IMPORTANT
If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

• Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
• Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
• metraonline.com.

© COPYRIGHT 2016 METRA ELECTRONICS CORPORATION

References

• Installer Institute Announces Closure after 31 Years | installerinstitute.edu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>