HOLDLAMP 100W Moving Head DJ Lights User Manual

June 15, 2024
HOLDLAMP

Moving Head Beam
User Manual

100W Moving Head DJ Lights

Please read the instruction carefully before use
Thank you for using our moving head light,
Note: the important information contained in this manual shall be installed and operated according to the requirements of the manual,
At the same time, please keep this manual properly for future use.

HOLDLAMP 100W Moving Head DJ Lights - Controlar

  1. menu
  2. Up
  3. Down
  4. Enter
  5. Control Panel
  6. Mic
  7. DMXIN
  8. DMX OUT
  9. use
  10. switch
  11. Power Supply

Unpacking instructions

When you receive the equipment, open the package and check whether the contents are complete and intact.If not, please inform the carrier immediately and keep the package if shownDamage. Keep the packaging and all packaging materials for safe transportation of the equipment.

  • 1 lamp
  • 1 instruction manual
  • 1 bow support
  • 1 power cord
  • 2 screws (installed on the machine)

Safety instructions and operating instructions

When the power is plugged in and the switch is turned on, “RST” is displayed. Moving headlights are resettingBit. Please do not operate. When the power is plugged in and the switch is turned on, “RST” is displayed. shiftThe moving headlamp is resetting.
Please do not operate.

  1.  It must be inserted into the grounding power socket, which is only for indoor use;
  2. To avoid fire or electric shock hazards, do not expose this equipment to rain or moisture Wet. During operation, ensure that there are no flammable objects near the equipment.
  3.  Install the equipment in a well ventilated place at least 50 away from any surface Cm, make sure that the ventilation slot is not blocked.
  4.  Please disconnect the equipment from the power supply before any operation or maintenance.
  5. The ambient temperature should not exceed 40 °C, and the maximum ambient temperature should be 45 °C. do not. Operate the equipment at higher temperatures.
  6.  In case of failure, stop the equipment immediately and do not repair the equipment by yourself. Improper maintenance may cause damage and failure. Contact technical support to agree. Only use the same spare parts as the original parts to ensure that the power cord is not blocked or Damage;
  7. Don’t expose your eyes to light. For sensitive people, strong light can Can be a sign of seizures;
  8. Lamps and lanterns are only used for decoration, and are not suitable for ordinary household lighting;
  9. Replace the fuse: Unplug the device from the power supply. Secure the fuse with a screwdriver Remove the silk seat from its original position. Take out the burnt fuse and replace it with Fuses with the same characteristics. Rotate the screws again and connect the device to On the power supply.
  10. Warning: if the fuse is still burning after replacement, please stop  Use; Please contact customer support for further instructions. Continue to use can Can cause serious damage;
  11. Fix the device with the screw holes on the bracket. Ensure that the equipment is firmly fixed to prevent Stop vibration and movement during operation, and always check the support equipment Whether the structure is firm enough to bear at least 10 times the weight of the equipment Equipment;
  12. The equipment must be fixed by professionals in places beyond people’s reach, any No one can pass under or above the crosswalk;
  13. Scrap of products: this sign indicates that this product should not be thrown into the European common market In the household garbage of the country. In order to protect the environment and / or human health,Waste should be recycled in a responsible manner to support the sustainable recycling of resources Utilization. If you need to recycle second-hand electrical appliances, please go to the electrical appliances collection center or contact you Contact the dealer who purchased the product. They will ensure the ecological recycling of products;

CAUTION
DO NOT OPEN THE HOUSING SHOCK HAZARD
Please read this manual carefully before operating this product.

Installation instructions

HOLDLAMP 100W Moving Head DJ Lights - Setup

  1. Instruct to install the bow bracket,Fix with screws after installation.
  2. Indicates that the hook bracket is connected with the bowlype support installation.
  3. Indicate to confirm your bracket position Whether it is installed correctly.
  4. Indicate that your bracket is No, the installation was successful.

Note: hook type support is not included in the package

Startup steps of various modes

  1. Automatic mode
    Press “menu” to find “SLND”, press “enter”, press “up” or “down” to select “ATO”, and press “enter” to start.

  2.  Sound mode:
    Press “menu” to find “SLND”, press “enter”, press “up” or “down” to select “sound”, and press “enter” to start. Adjust the sound sensitivity. Press “enter” to find “sene”. Press “up” or “down” to start the speed of sound sensitivity (the higher the value, the faster, and the lower the value, the slower)

  3. Console mode and master-slave mode:
    DMX out to 1 lamp dmxin; No.1 lamp DMX out is connected to No.2 lamp dmxin; Press “menu” to find “addr”, press “enter”, display “A001”, press “up” or “down” to select the value of the console;
    Setting of master-slave machine: No. 1 lamp is set as self-propelled or voice control function according to the starting mode; 2, 3, 4 set to DMX512 mode: DMX address code is 001

HOLDLAMP 100W Moving Head DJ Lights - Setup1HOLDLAMP 100W Moving Head DJ Lights -
Controlar1

Serial number/main menu explain
Address code selection
Channel selection
Console  goone’snway Voice control
Motor X-axis forward and reverse setting
Motor Y-axis forward and reverse setting
![HOLDLAMP 100W Moving Head DJ Lights - icon21](https://manuals.plus/wp-

content/uploads/2023/12/HOLDLAMP-100W-Moving-Head-DJ-Lights-icon21.jpg) Voice control sensitivity adjustment
| Constant on screen setting
| Screen forward and reverse settings
| Software version number
| Temperature display
| Restore factory settings
Fine tuning menu| Press the menu key 5S to call up the fine adjustment menu
| Forward and reverse fine tuning
| Forward and reverse fine tuning
| Forward and reverse fine tuning
| Forward and reverse fine tuning

Product parameters

  1. Working voltage: AC220V / 50Hz
  2. Control mode: International DMX512, 12 channels
  3. Working mode: DMX512, master / slave, self-propelled, voice control
  4. Dimming mode: 0 — 100% super smooth dimming
  5. Stroboscopic: 25 times / second

DMX channel function description

12 channels function DMX value describe
1 X axis 0-255
2 X-axis trim 0-255
Y axis 0-255
Y-axis trim 0-255
S X Y axis speed 0-255 Speed from fast to slow
6 Pattern white light 0-255 Pattern dimming from dark to light
Pattern stroboscopic 0 No function
1-255 Sii1Ch’D1XS streboscopic speed from slow to fastaKZ-25H/
8 Color disc 0-15 white light
16–31 Color 1
32–47 Color 2
48-43 Color 3
64–79 Color 4
80–95 Color 5
96–111 Color 6
112–127 Color 7
128-191 Cbckwise color automatic switching from fast to sbw
192-255 Counterdodcwise odor automatic switching from slaw to fast
9 Pattern disc 0-7 white light
8–15 Pattern 1
16-23 Pattern 2
24-31 Pattern 3
32-39 Pattern 4
40-47 Pattern 5
48-55 Pattern 6
56-63 Pattern 7
64-73 Pattern 7 jitter from slow to fast
74-82 Pattern 6 jitter from slow to fast
83-91 Pattern 5 jitter from slow to fast
92-100 Pattern 4 jitter from slow to fast
101-109 Pattern 3 jitter from slow to fast
110-118 Pattern 2 jitter from slow to fast
119-127 Pattern 1 jitter from slow to fast
128-191 Clockwise color automatic switching from fast to slow
192-255 Cantedock Ase auto automatic switchingkm shy to fast
10 Prism 0-7 Close prism
8-127 Open prism
128-255 Prism rotation from slow to fast
11 Macro function 0-49 Channel 1 to channel 10 are valid
50-200 go one’s own way
201-255 Lamp body voice control
12 reset 0-240 No function
241-255 Lamp body reset, 5S effective.

If it is detected that the temperature control is not installed or short circuited, it will be protected and run with low brightness to display err
In DMX mode, if there is no DMX signal, the first nixie tube will flash, and the middle bit of the last nixie tube after the screensaver will flash
In the display temperature menu (ERR), it means no installation or short circuit

CAUTION
DO NOT OPEN THE HOUSING SHOCK HAZARD
Please read this manual carefully before operating this product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals