HOLDLAMP 4 Arm RGB Moving Head Light User Manual

HOLDLAMP 4 Arm RGB Moving Head Light

Please read the instruction carefully before use
Thank you for using our moving head light,

Note: the important information contained in this manual shall be installed and operated according to the requirements of the manual,

At the same time, please keep this manual properly for future use.

1. Up
2. Down
3. OK
4. Menu
5. Display screen
6. In put
7. Output
8. Fuse
9. Power supply
10. Cooling hole

Unpacking instructions

When you receive the equipment, open the package and check whether the contents are complete and intact. If not, please inform the carrier immediately and keep the package if shown Damage. Keep the packaging and all packaging materials for safe transportation of the equipment.

Packing list

• 1 set of lamps
• 2 arch bracket
• 1 power cord
• 2 screws (installed on the machine)
• 1 operating manual

Safety instructions and operating instructions
When the power is plugged in and the switch is turned on, “RST” is displayed. Moving headlights are resetting Bit. Please do not operate. When the power is plugged in and the switch is turned on, “RST” is displayed. shift The moving headlamp is resetting. Please do not operate.

1. It must be inserted into the grounding power socket, which is only for indoor use;
2. To avoid fire or electric shock hazards, do not expose this equipment to rain or moisture Wet. During operation, ensure that there are no flammable objects near the equipment.
3. Install the equipment in a well ventilated place at least SO away from any surface Cm, make sure that the ventilation slot is not blocked.
4. Please disconnect the equipment from the power supply before any operation or maintenance.
5. The ambient temperature should not exceed 40 °C, and the maximum ambient temperature should be 45 ° C. do not. Operate the equipment at higher temperatures.
6. In case of failure, stop the equipment immediately and do not repair the equipment by yourself. Improper maintenance may cause damage and failure. Contact technical support to agree. Only use the same spare parts as the original parts to ensure that the power cord is not blocked or Damage;
7. Don’t expose your eyes to light. For sensitive people, strong light can Can be a sign of seizures;
8. Lamps and lanterns are only used for decoration, and are not suitable for ordinary household lighting;
9. Replace the fuse : Unplug the device from the power supply. Secure the fuse with a screwdriver Remove the silk seat from its original position. Take out the burnt fuse and replace it with Fuses with the same characteristics. Rotate the screws again and connect the device to On the power supply.
10. Warning : if the fuse is still burning after replacement, please stop Use; Please contact customer support for further instructions. Continue to use can cause serious damage;
11. Fix the device with the screw holes on the bracket. Ensure that the equipment is firmly fixed to prevent Stop vibration and movement during operation, and always check the support equipment Whether the structure is firm enough to bear at least 10 times the weight of the equipment Equipment;
12. The equipment must be fixed by professionals in places beyond people’s reach, any No one can pass under or above the crosswalk;
13. Scrap of products : this sign indicates that this product should not be thrown into the European common market In the household garbage of the country. In order to protect the environment and / or human health, Waste should be recycled in a responsible manner to support the sustainable recycling of resources Utilization. If you need to recycle second-hand electrical appliances, please go to the electrical appliances collection center or contact you Contact the dealer who purchased the product. They will ensure the ecological recycling of products;

CAUTION DO NOT OPEN THE HOUSING SHOCK HAZARD
Please read this manual carefully before operating this product.

Note: hook type support is not included in the package

Startup steps of various modes

1. Automatic mode Press “MENU” to find “Shou”, press “ENTER” and then press “Up” or “Down” ” Key to select “Au01”, “Au02”, “Au03”, or “Au04”, and press “ENTER”.
2. Sound mode
   • Press “MENU” to find “Shou” and press “ENTER”.
   • Press “Up” or “Down” to select “Son1” or “Son2”, and press “ENTER”.
   • Press “MENU” to find “SEnS”, press “ENTER” to start sound sensitivity adjustment, and press “UP” or “DOWN” key Start the speed of sound sensitivity (Higher values are faster, lower values are slower)
3. Console mode and master-slave mode
   • DMX OUT to No. 1 lamp DMX IN; No. 1 lamp DMX OUT connected to No. 2 lamp With DMX IN;
   • Press “MENU” to find “Addr”, press “ENTER” to display “A001”, and press “Up” or “Down” selects the value of the console;
   • Master slave setting: The No. 1 lamp is set to be self-propelled or voice controlled according to the startup mode
   • Function; 2, 3, 4 * Set to DMX512 mode** : DMX address code is 001;

1. Operating Voltage: AC95V-245V/50Hz
2. Lamp bead parameters: 16 PCS four in one lamp beads, 2 PCS white stroboscopic, 1 PCS red laser, 1 PCS green laser
3. Control mode : International DMX512, 16 channels
4. Working mode : DMX512, master / slave, self-propelled, voice control
5. Dimming mode : 0~100% super smooth dimming
6. Stroboscopic: 20 times / second

Menu

Documents / Resources

| HOLDLAMP 4 Arm RGB Moving Head Light [pdf] User Manual
4 Arm RGB Moving Head Light, RGB Moving Head Light, Moving Head Light, Head Light, Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>