OUTDOOR ROOMS HVGW-1224 Havenwood Fire Pit Installation Guide
- June 4, 2024
- OUTDOOR ROOMS
Table of Contents
THE OUTDOOR
GREATROOM
COMPANY
Havenwood Fire Pit
Installation Instructions for
HVGW-1224 and HVDG-1224
Required Tools
• 2 Open Ended Wrenches
To make gas connections
• Leather Gloves
To protect hands from rough edges found on the coffee table.
• One (1) AAA Battery (not included)
Required for piezoelectric igniter installation.
• Electric Screw Gun with Philips tip
(Used for attaching brackets to top and top to frame.)
Included in packaging
Placing and Assembling the Fire Pit Table
(Everblend Top)
1. Remove all components from packaging.
2. Move the base (remove door) to desired location and set into place.
3. When locating your table, refer to the manual included with your
burner and maintain clearance to combustibles.
4. Assemble the 2 brackets in the Everblend top using the 4X provided
¼-20 Philips head screws.
5. With the help of another person, carefully set the Everblend top into place on the base and center it. Using the 4 sheetmetal screws provided, secure the Everblend top to the base.
6. Set burner into place. See the section labeled Gas Connection and Igniter Installation to install gas lines and piezoelectric igniter.
Igniter Installation
- Locate CF-SPARKER inside of crystal fire burner box.
- Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included) with + end out.
- Install CF-SPARKER into control panel as shown below.
- Depress CF-SPARKER button to test your sparker.
- Located and orient sparker box on control panel as shown. Sparker box must be installed before burner valve.
Gas Connections
Read and understand your Crystal Fire® Plus owner’s manual before beginning burner hookups or using the device.
-
See Crystal Fire® Plus instruction manual for burner installation.
• All gas connections were completed at the factory. -
Check all connections for leaks. If needed, tighten connection with 2 wrenches and re-check for leaks.
-
Attach burner valve to control panel with provided screws as shown below. Ensure sparker box is installed before this step
Thermocouple Installation
- Refer to Crystal Fire® Plus instruction manual for detailed attachment of thermocouple.
- Attach thermocouple to burner valve as shown below.
Electrode Installation
- Connect igniter and ground wire to sparker box. Both wires can connect to either connection point. The unit will operate in either configuration.
- Test system by pushing the button on the igniter. Consult the troubleshooting section of the Crystal Fire® Plus Burner Owner’s Manual, if the spark is weak, intermittent, or not present.
Locating your Tank
- Your tank should be positioned so that the fuel can be shut off after each use.
- Slide the tank into the framework past the line shown below. This is to allow the door to close completely.
- Confirm all hoses are clear and not touching the burner.
Position tank behind this line
- Install door by setting the bottom on the catching hooks first and then closing. Magnets in the table will hold door closed.
Finishing touches
Once fire pit is set up and in the desired position, scatter decorative glass on burner surface forming an even layer of beads.
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED GLASS BEADS OR OTHER APPROVED FIRE MEDIA
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITH BURNER COVER IN PLACE
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to hooking up your linear burner, including safety information, proper tightening of connections with two wrenches and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CFP1224 BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE® PLUS MANUAL. IF YOU ARE UNSURE OF HOW TO COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating, all gas connections must be fully checked for leaks
Warranty: Fire pit tables are covered under a 1-year manufacturer’s warranty. Please visit https://www.outdoorrooms.com/product-registration to register your product.
WARNING: This product can expose you to chemicals including Carbon Monoxide and Benzene which are known to the State of California to cause cancer or birth defects or reproductive harm. For more information, visit www.P65Warnings.ca.gov
Thank you for purchasing an Outdoor GreatRoom Company product! This fire pit was made with pride in the USA.
9583 217th St. W. • Lakeville, MN 55044
Toll Free: 1-866-303-4028 •
Sales@OutdoorRooms.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>