FORCE 39151 16 functions Wireless Computer Instruction Manual
- June 15, 2024
- FORCE
Table of Contents
FORCE 39151 16 functions Wireless Computer
INSTALLATION INSTRUCTION
- Installation of computer bracket
- Mounting computer
- Installation of spoke magnet
- Attention: Mount the sensor on the front side of the fork.
Change battery
Attention:
- When battery is replaced NO saved data gets lost.
- Use only CR2032 3V batteries.
- Make sure that the sealing
Tire size chart
ETRTO Tire size Circumference (mm)
50-305 16x 1.95 1265
47-406 20 x 1.75 1580
50-406 20x 2.00 1600
50-507 24x 2.00 1910
54-507 24 x 2.10 1930
54-507 24x 2.125 1930
57-507 24x 2.25 1955
40-559 26 X 1.50 2030
50-559 26x 1.95 2050
50-559 26x 2.00 2075
54-559 26x 2.10 2100
57-559 26x 2.25 2120
60-559 26 X 2.35 2160
60-559 26x 2.40 2183
54-584 27.5×2.10 2195
55-584 27.5×2.20 2221
57-584 27.5×2.25 2215
ETRTO Tire size Circumference
Imm)
60-584 27.5×2.35 2240
60-584 27.5 X 2.40 2244
20-622 28, 2100
23-622 28 X 0.90
2125
25-622 28 X 1.00 2135
28-622 28 X 1.10
2150
35-622 28 X 1.35 2185
40-622 28 X 1.50 2220
42-622 28 X 1.60 2230
44-622 28 X 1.625 2235
47-622 28 X 1.75 2250
50-622 29×2.00 2280
54-622 29 X 2.10 2310
55-622 29×2.20 2347
57-622 29×2.25 2330
60-622 29 X 2.35 2340
60-622 29×2.40 2378
Display
Set computer
- Press key for 3 seconds to access orto exit the settings menu.
- Use the key to browse from one setting to the other.
- To access the selected setting. briefly press the key.
- Select the desired setting with the key and confirm with the key.
- When the setting has been made, the display shows “Set 0K”.
- If there is no reaction, the menu closes automatically after one minute.
Icons
- Signal reception
- Shows selected speed unit
- Shows selected bike 1 or bike 2
- Backlight enabled
- In night loop mode enabled
- Comparison of the current speed with the average speed
Keys
Functions
Backlight
- Press and simultaneously to switch the backlight on or off.
- After pressing any key, the lights are on for approx. 6 seconds.
Change bike
- Press and simultaneously for 3 seconds. The computer
- Press changes to the selected bike settings.
Loop mode
- With the infinite loop mode enabled, the most important functions are automatically forwarded every 4 seconds during the ride. The infinite loop mode is disabled by pressing any key.
Rest / Sleep mode
- The computer is equipped with a vibration sensor.
- If no vibrations or signals are registered, the computer switches to rest mode after 6 minutes and displays the time.
- As soon as it picks up vibrations, the computer switches back to operating mode.
- If the computer is in sleep mode, it wakes up when any key is pressed.
Reset your data
- Press the key for 3 seconds to reset your data.
- Settings are not modified.
SPECIFICATIONS
- Speed sensor: non-contact type magnetic sensors
- Battery Type: lx 3V CR 2032 battery Battery life (Model No. CR2032) is approximately 1.5 years (based on two hours of daily riding)
- Wireless transmission: 125 kHz low-frequency transmission
- Size and weight:
- size: length 60 mm,
- width: 40 mm,
- height: 10 mm
- weight with holder and batteries: 34 g
- The wheel circumference input Unit: mm
- Operating speed: OOC – 500C
MEASURED DATA /MEASURING RANGE
- Current speed 1.0KM/H–99.9KM/H(MPH)
- Maximum speed 1.0KM/H–99.9KM/H(MPH)
- Average speed 1.0KM/H–99.9KM/H(MPH)
- Trip distance A 0.1-99999.9KM(MILE)
- Trip distance B 0.1-99999.9KM(MILE)
- Total distance 1-999999KM(MI LE)
- Elapsed time 0:00.00-99H:59M:595
- Clock time 0:00-23:59
WARRANTY
- Warranty does not apply to damage due to high and low temperatures, physical damage resulting from abuse, improper repair, improper fit, alternations of the fixture or improper use.
- The current version of the manual and declaration of conformity can be found on the website www.FORCE.BIKE.
CONTACT
- Dovozce / Wrobce
- Importer / Producer
- KCK Cyklosport•Mode s.r.o., 348, 765 02 Otrokovice Kvitkovice, CZ
- www.kckcyklosport.cz, www.force.bike.
- Zemé pivodu Cina/ Made in China
The instruction manual is part Of this product. It contains important information on safety, assembly, and disposal. Before using this product, you must familiarise yourself with all operating and safety instructions. Use the product only as described in the manual and only for the indicated application areas. If you pass on the product to third parties, provide it with all the documentation.