crosswater BEL-F6031-E-FT-WH Belgravia Slipper Freestanding Footed Bathtub Instruction Manual

June 15, 2024
crosswater

crosswater-LOGO

crosswater BEL-F6031-E-FT-WH Belgravia Slipper Freestanding Footed

Bathtub

crosswater-BEL-F6031-E-FT-WH-Belgravia-Slipper-Freestanding-Footed-Bathtub-
PRODUCT

Introduction

  • This bathtub has been fully inspected throughout the production process and only leaves our factory after a 15-step QC process.
  • Unpack and inspect the bathtub before removing the fixture being replaced, if applicable.
  • Carefully remove the bathtub from the box, taking care the bathtub is carried in the bag. Check that all parts have been supplied.
  • Before beginning installation of the bathtub please check for any damage that may have occurred during transport.

Note: Damage claims cannot be made during or after installation.

  • Improper installation shall result in loss of warranty in case of damage caused by impacts or rubbing against rough surfaces.
  • Before installing the bathtub prepare a connection of water inlet/outlet.
  • Pay attention to levelling of the floor where the bathtub will be located, ensuring it can take the weight of the bathtub, water and bather(s).
  • The customer may choose the type and location of the faucets, installation instructions should be supplied by the faucet manufacturer.
  • The installation procedure of the bathtub may differ from that described in the installation instructions, depending on where you wish the bathtub to be located.
  • The wet surface of the bathtub may create a risk of slipping which may increase by using soap, shampoo, oils and similar products.

IMPORTANT: Please read these instructions carefully before you begin and retain them for future reference.
We do not accept responsibility for any problems that may occur through incorrect installation.

RECOMMENDATIONS

  • The walls and floor should be fully tiled and finished before installation.
  • This ensures that the product is installed flat to the tile face and allows the product to be easily removed if required in the future.
  • Remove the protective packaging after installation of the bathtub.
  • Only fill the bathtub with water up to 2/3 of its height.
  • Use US-CW11 waste flow product with this bathtub.

Installation notes

  • The installation must comply with all plumbing codes including local codes and be installed by a licensed plumbing contractor.
  • Store the bathtub in a safe place until you begin installation to avoid any damage.
  • Assemble the bathtub on a mat to protect against damage to the bathtub surface.
  • Avoid getting cement, grit, sand or masonry products onto the surface.
  • Protect and cover the bathtub during the installation period to prevent damage from occurring.
  • Never use brown tape or gaffer tape directly onto the surface. If the bath has to be repacked remember to avoid taping directly onto the surface of the bathtub.
  • IMPORTANT: Turn off the main water supply before connecting to any existing pipework or doing any maintenance.
  • WARNING! Please check for any hidden pipes and cables, electric or otherwise, before drilling holes in a wall or floor.

Dimensions

crosswater-BEL-F6031-E-FT-WH-Belgravia-Slipper-Freestanding-Footed-Bathtub-
FIG-1

Tools required

crosswater-BEL-F6031-E-FT-WH-Belgravia-Slipper-Freestanding-Footed-Bathtub-
FIG-2

Installation – carriage

IMPORTANT
This bathtub is heavy and installation requires 2 people.
Crosswater London cannot accept responsibility for any injuries caused to those attempting to install this bathtub without adequate and appropriate tools or resources.

  • Remove the bathtub from the packaging using the bag with handles.
  • Use the bag with handles to lift and move the bathtub.
  • Do not drag the bathtub over rough surfaces or sharp objects. Lift and place the bathtub into position.
  • Do not drop the bathtub!

crosswater-BEL-F6031-E-FT-WH-Belgravia-Slipper-Freestanding-Footed-
Bathtub-FIG-3 Installation

Feet

  • Fit the chosen feet following the installation instructions supplied with the foot kit.

Waste

  • This installation guide does not include details of the waste connection; the final decision about the installation of the waste connection should be made by a licensed plumber.
  • Install the waste according to the installation instructions supplied with the waste.

crosswater-BEL-F6031-E-FT-WH-Belgravia-Slipper-Freestanding-Footed-Bathtub-
FIG-4

WARNING: DO NOT OVERTIGHTEN the waste as this may cause long-term damage to the bath.
We recommend using a torque wrench to tighten the waste by using a torque force between 25Nm or 18.5 ft/lb and 50Nm or 36.8 ft/lb.

crosswater-BEL-F6031-E-FT-WH-Belgravia-Slipper-Freestanding-Footed-Bathtub-
FIG-5

  • Lower the bathtub into position using a small amount of silicone under each foot.

Cleaning Instructions

  • Clean the bath regularly with non-abrasive soap and warm water. Fully rinse after cleaning.
  • While Clearstone is highly stain resistant, it is recommended that bath water containing additives such as oils or salts is always drained and rinsed immediately after use.
  • Please note that hair dyes and colour cosmetics (eg. mascara, lipstick, face powder) may leave a slight discolouration if not removed immediately.
  • If any strong chemicals come into contact with the bathtub, remove and rinse immediately.
  • Water temperature should not exceed 49°C/120°F.
  • For a fine scratch or a slight mark, use 1500-grade sandpaper. Gently sand the area with water. For best results, limit sanding to the smallest possible area around the scratch. Re-polish the surface afterwards using a neutral polishing compound or toothpaste. It may be possible to polish very fine scratches away without using abrasive papers: scrub gently with a soft brush or plastic pad (not metal scouring pad) and a mildly abrasive cream cleaner. Afterwards, scrub the whole area with plenty of clean water and re-polish as before.
  • If the scratch or mark is too deep and cannot be repaired using the above method, it is possible to purchase a repair kit in US-CRK. In order to remove the scratches, follow the instructions included in the kit.

Warranty

  • This Crosswater London product is covered by a limited lifetime warranty.
  • For full details, terms and conditions please visit our website.

CONTACT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals