THE OUTDOOR PLUS DT041723 Electrical Dial Timer Instruction Manual
- June 15, 2024
- THE OUTDOOR PLUS
Table of Contents
THE OUTDOOR PLUS DT041723 Electrical Dial Timer
Product Information
Specifications
- Model: Dial Timer
- Certifications: LR3730, E76987
Dial Timer Overview
The Dial Timer is a device designed to control the timing of various
equipment. It is important to read and understand the following information
before operating the Dial Timer.
Safety Precautions
Before using the Dial Timer, please take note of the following safety
precautions:
- This timer should not be used in precision timing applications where inaccurate timing could have dangerous consequences (i.e. sun lamps, sauna, etc.).
- Only qualified personnel should install and service this equipment. Failure to follow instructions may result in serious injury or death.
- Ensure power is turned off before performing any maintenance or repair on this equipment to avoid electric shock.
- Do not touch the timer during or immediately after use, as the surface may be hot and cause burns.
- Do not use this equipment in areas where flammable gases or liquids are present, as it may result in explosion or fire.
- Keep hands and other body parts clear of moving parts during operation to avoid injury.
- Use this equipment only for its intended purpose. Misuse or modification of the equipment may result in injury or damage to the equipment.
- Do not exceed the maximum capacity of the timer, as overloading may cause damage and result in injury.
- Only authorized personnel should perform repairs on this equipment. Unauthorized repairs may result in injury or damage to the equipment.
- Do not touch the timer with wet hands or in wet conditions, as this increases the risk of electric shock.
- There are no user-serviceable parts inside this equipment.
Disassembly may result in injury or damage to the equipment and will void the warranty.
Installation Information
Before installing the Dial Timer, please follow these instructions:
- Ensure that the power supply is turned off.
- Mount the Dial Timer in a suitable location, considering accessibility and visibility.
- Connect the necessary wiring according to the Wiring Information section (see page 7).
- Once the installation is complete, turn on the power supply and test the functionality of the Dial Timer.
Dial Timer Operation
To start and stop the Timer:
- Ensure that the power supply is turned on.
- Rotate the dial to set the desired time duration.
- Press the start button to initiate the countdown.
- The Timer will automatically stop once the set time duration has elapsed.
Maintenance and Troubleshooting
To ensure proper performance and longevity of the Dial Timer,regular
maintenance is recommended. If you encounter any issues, please refer to the
following troubleshooting steps:
Maintenance
- Regularly clean the surface of the Dial Timer using a soft, dry cloth.
- Inspect the wiring connections for any signs of damage or loose connections. Tighten or repair as necessary.
- Check for any obstructions or debris that may affect the operation of the Timer. Remove any obstacles if found.
Troubleshooting
If the Dial Timer is not functioning properly, please try the following:
- Check if the power supply is properly connected and turned on.
- Ensure that the Timer is set to the correct time duration.
- Verify that the wiring connections are secure and properly installed.
- If the issue persists, contact our customer support for further assistance (see page 12).
Warranty & Support
For warranty information and customer support, please refer to the following:
- Customer Support: 909-460-5579
- Warranty Information: Please refer to page 13 for detailed warranty coverage.
Frequently Asked Questions (FAQ)
Q: Can I use the Dial Timer with sun lamps or sauna?
A: No, the Dial Timer should not be used in precision timing applications
where inaccurate timing could have dangerous consequences.
Q: Can I perform repairs on the Dial Timer myself?
A: No, only authorized personnel should perform repairs on this equipment.
Unauthorized repairs may result in injury or damage to the equipment.
Q: What should I do if the Timer is not functioning properly?
A: First, check if the power supply is properly connected and turned on.
Ensure that the Timer is set to the correct time duration. Verify that the
wiring connections are secure and properly installed. If the issue persists,
contact our customer support for further assistance.
DIAL TIMER
INSTALLATION & OPERATION INSTRUCTIONS
Read all instructions before you operate your dial timer.
Save these instructions!
TO INSTALLER: Leave this manual with the DIAL TIMER.
TO CONSUMER: Keep this manual for future reference.
CAUTION:
This timer should not be used in precision timing applications where
inaccurate timing could have dangerous consequences (i.e. sun lamps, sauna,
etcetera)
WARNING:
ELECTRIC SHOCK HAZARD. Only qualified personnel should install and service
this equipment. Failure to follow instructions may result in serious injury or
death.
WARNING LABELS & SYMBOLS
THIS IS A SAFETY ALERT SYMBOL
When you see this symbol in on the fire feature or manual, look for one of the
following signal word panels alerting you to the potential for personl injury,
death or major properety damage.
CAUTION:
- HIGH VOLTAGE. Ensure power is turned off before performing any maintenance or repair on this equipment. Failure to do so may result in electric shock.
- HOT SURFACE. Do not touch the timer during or immediately after use, as the surface may be hot and cause burns.
WARNING:
EXPLOSION HAZARD. Do not use this equipment in areas where flammable gases or
liquids are present. Doing so may result in explosion or fire.
CAUTION:
- MOVING PARTS. Keep hands and other body parts clear of moving parts during opera-tion. Failure to do so may result in injury.
- IMPROPER USE. Use this equipment only for its intended purpose. Misuse or modifica-tion of the equipment may result in injury or damage to the equipment.
- UNAUTHORIZED REPAIRS. Only authorized personnel should perform repairs on this equipment. Unauthorized repairs may result in injury or damage to the equipment.
DANGER:
- RISK OF ELECTRIC SHOCK. Do not touch the timer with wet hands or in wet conditions, as this increases the risk of electric shock.
- DO NOT DISASSEMBLE. There are no user-serviceable parts inside this equipment. Disassembly may result in injury or damage to the equipment, and will void the warranty.
DIAL TIMER INFORMATION
Product Overview
DIAL TIMER COMMERICAL SERIES:
The Outdoor Plus Dial Timer is designed to be a convenient replacement for any
standard single or multi-gang wall switch. This mechanical timer is highly
energy-efficient and does not rely on electricity to function. Additionally,
it has been specifically engineered to automatically limit the ON times for
outdoor devices such as lighting, irrigation systems, pool pumps, and other
energy-consuming loads, making it an ideal choice for outdoor applications.
FEATURES:
- The mechanical timer is highly reliable and ensures accurate timing.
- The timer has been certified by CSA International, ensuring it meets safety and performance standards.
- The timer is easy to install, making it a convenient replacement for standard wall switches.
- The timer is simple to operate and does not require any special training.
- The timer is designed to withstand various outdoor weather conditions.
- The timer helps ensure compliance with building codes.
- The timer helps enhance the overall guest experience in hotels and restaurants.
- The timer improves safety in commercial buildings and public areas.Improves safety: Improves safety in commercial buildings and public areas.
Technical Specification
RATINGS:
Resistive:| 20 Amp, 125 VAC, 50/60 Hz
10 Amp, 250 VAC, 50/60 Hz
10 Amp, 277 VAC, 50/60 Hz
---|---
Tungsten:| 7 Amp, 125 VAC
Motor:| 1 HP, 120 VAC, 50/60 Hz
2 HP, 240 VAC, 50/60 Hz
Dimensions:| 2.79″ H x 1.6″ W x 1.19″ D
SPECIFICATION
The Dial Timer is designed to be a direct replacement for a standard wall switch in a single gang 2 ½” deep junction box. Its dimensions and design are appropriate for this purpose, and it is easy to install without requiring any modifications to the existing setup. The timer features a spiral time scale that makes it easy to select a desired time setting, and it comes with a molded white knob and brushed metal finish wall plate that can be easily secured without screws or other hardware. The polymeric time dial is designed to replace a standard switch plate without requir-ing any modifications. Additionally, the timer is UL listed, ensuring its quality and safety. Overall, the Dial Timer is a convenient and reliable choice for replacing a standard wall switch and controlling various energy-consuming loads such as fans, lighting, motors, and heaters.
Installation Information
The spring wound timer is designed for easy installation, and can be installed just like a standard light switch in a 2-1/2 inch deep vertically installed junction box. It can be used to replace a standard single pole, 3-way, or double pole single-throw wall switch (depending on the timer model). Once installed, the spring wound timer will automatically turn off lights, fans, air conditioners, and other energy-consuming loads after a preset timing period, making it a convenient and energy-efficient choice for controlling various appliances.
INSTALLATION:
- Turn off the power to the circuit you’re working on by switching off the circuit breaker in your main electrical panel.
- Remove the cover plate from the existing switch by taking out the screws that hold it in place.
- Strip the wires about half an inch long according to the strip gauge on the back of the timer.
- Insert the stripped end of the wires under the pressure plate of the terminal screws on the side of the Dial Timer, using the screws provided in the plastic bag. Tighten the screws securely, and use copper wire only.
- Put the Dial Timer into a standard wall junction box that is 2-1/2 inches deep, making sure that the “TOP” (as indicated on the front of the timer) is in the correct position. Fasten the timer to the junction box using the two long screws provided.
- Slip the time dial plate over the threaded extension of the Dial Timer, with the “OFF” mark of the time dial plate on top as indicated on the front of the timer.
- Secure the time dial plate to the Dial Timer using the stamped nut that is provided.
- If you’re using a regular switch plate, the nut that comes with the timer will hold the plate in place, so you don’t need to use the screws that come with the plate. If you’re using a fancier plate, use the two screws that come with it to attach it to the metal tabs on the timer’s opposite ends. Just be sure not to tighten the screws too much.
- Slide the plastic time dial plate onto the threaded extension of the timer. Make sure that the “OFF” mark on the dial plate is facing up. Use the nut that comes with the timer to secure the dial plate in place. Be careful not to tighten the nut too much.
- Put the knob on the timer shaft so that the pointer on the knob is pointing to the “OFF” mark on the dial plate. The knob has a hole in the shape of the letter “D” that matches the “D” shaped shaft on the timer.
- Turn the power back on at the circuit breaker.
Wiring Information
USING A DIAL TIMER
USING A DIAL TIMER
USING A CONTROL PANEL, DIAL TIMER & E-STOP
USING A DIAL TIMER & E-STOP
USING A CONTROL PANEL, DIAL TIMER & E-STOP
DIAL TIMER OPERATION
Start & Stop of the Timer
The Dial Timer can be used by anyone who needs to automate the turning on and off of their device or appliance, such as our Fire Feature.
IMPORTANT:
If you are unsure about how to operate the timer, we recommend consulting a
licensed electrician for assistance.
ALSO IMPORTANT:
Always make sure to read the instructions carefully and follow them closely to
ensure safe and proper operation of the timer.
HOW-TO OPERATE:
To set the timer, turn it clockwise to your desired time. The timer will
automatically turn off your device at the end of the time you set. However, if
your timer is wired for reverse action, it will turn your device on at the end
of the preset time instead.
NOTE:
Your timer may appear different, but the function of the timer will remain the
same. This is just an illustration.
DIAL TIMER PERFORMANCE
Maintenance and Trubleshooting
TROUBLE SHOOT GUIDE
PROBLEM | SOLUTION |
---|---|
Timer doesn’t turn ON Fire Pit. | Make sure the timer is properly |
connected to the power source and the Fire Feature. Check the timer settings to ensure it is programmed correctly.
Fire Pit Turns ON but not OFF.
| Check the timer settings to ensure it is programmed correctly. Make sure the timer is not damaged or malfunctioning.
Timer doesn’t keep time accurately.
| Check the power source to ensure it is working properly. If it is a
mechanical timer, make sure the clock is set correctly.
Timer makes noises.| This could be caused by a loose connection or a
faulty timer. Check the connections to ensure they are secure. If the problem
persists, it may be necessary to replace the timer.
WARRANTY & SUPPORT
Customer Support Contact Information
At The Outdoor Plus, we are committed to providing excellent customer service
to all of our customers. If you need assistance in ordering parts for your
accessories, please contact our sales team at
sales@theoutdoorplus.com Our knowledgeable
sales team can assist you in identifying the correct parts and accessories
needed for your order.
If you need assistance in installing your Accessories, please contact our
support team at:
support@theoutdoorplus.com Our team of
experts can provide guidance and assistance to ensure a safe and successful
installation.
We are dedicated to making your experience with The Outdoor Plus as seamless
and enjoyable as possible. Don’t hesitate to reach out to us with any
questions or concerns you may have. Our team is always ready to assist you in
any way we can.
REGISTER YOUR FIRE FEATURE ACCESSORIES:
Thank you for choosing The Outdoor Plus for your fire feature accessory needs.
We hope that your product has exceeded your expectations and provided you with
countless hours of enjoyment.
We would like to remind you of the importance of registering your product
online. By doing so, you will receive the most efficient and helpful service
should you ever need to use your product warranty. Our registration process is
quick and easy, and it will help us to better serve you in the future.
Thank you again for choosing The Outdoor Plus, and we hope to continue serving you for many years to come.
SCAN TO REGISTER YOUR PRODUCT ONLINE:
WARRANTY INFORMATION
The Outdoor Plus Company (TOP) warranties its products against manufacturing defects that prevent safe and proper functioning as follows:
Electronics, Gas Valves, & Pilot Assembly:
Commercial – 6 Months ; Residential – 1 Year
Stainless Steel & Aluminum Pans:
Commercial – 1 year; Residential – 5 years
Burner Ring & Burner Bars:
Lifetime Warranty
Electrodes & Spark Igniter:
Not Warrantied (due to lifespan)
- This commences from the date of original sale /shipment from The Outdoor Plus
- The warranty on parts and in-house labor will apply only to claims presented to us by T.O.P’s original customer and is in lieu of all other warranties expressed or implied.
- The defective product must be sent back to TOP with a Return Merchandise Authorization (RMA) issued by TOP for that specific product which states the nature of the defect or warranty claim. The origi-nal purchase information will be required.
- Product to be returned should be packed carefully. The Outdoor Plus is not responsible for shipping damage on returned items.
- RMA’s are only valid for 30 days which states the nature of the defect or warranty claim after the expiration date.
- The RMA number must be indicated on the outside of the return package and a copy of the RMA should be placed in the package with product.
- TOP is not responsible for damaged caused by overheating, modification, abuse, improper storage, installation, or maintenance.
- TOP is not responsible for surface level rust on metal products.
- TOP is not responsible for the actions including negligence of the installer.
- Any labor involving installation or maintenance with the unit is not covered.
- This warranty does not cover claims for incidental or consequential damage and indirect collateral expenses arising from product defects or warranty repairs. Products manufactured by TOP include cLCus, UL, or CSA Certified models, of which cannot be altered or modified in any way.
- TOP is not responsible for local codes and will not accept a return on any product that is not approved for installation. Please check with your local author-ities or governing agencies for proper approvals before purchasing.
PRODUCT RETURN POLICY
- No returns on made-to-order goods.
- No returns on custom features, NO EXCETIONS.
- If a product is delivered incorrectly, it is the recipients responsibility to notify TOP within 48 hours. TOP is not responsible for incorrect or dam-aged packages and shipments 48 hours after they have been received. Please call 909-460-5579 or email: support@theoutdoorplus.com for help with warranty, replacements, returns, or if you have any support related questions.
PRODUCT TESTING PROGRAM
If you believe a unit or component you received is defective, The Outdoor Plus
will gladly test any component at T.O.P’s facility. TOP will cover shipping
back to you.
DEFECTIVE
If an item is found to be defective it will be repaired or replaced at T.O.P’s
discretion. TOP will absorb all costs of outgoing freight and replacement
costs if product is in warranty.
NON-DEFECTIVE
If the product is found to be non-defective it will be returned to the
customer – no credit will be given.
TOP ERROR
If a return is needed due to a mistake on T.O.P’s part, we will issue a RMA
and Return Services Label. When products are received at TOP, credit will be
issued for the products and the outgoing freight on the original invoice.
CUSTOMER ERROR
If an RMA is asked for and covers current new proucts in the original package,
we will authorize the return. The customer is responsible for the return
shipping. When products are received we will issue credit for the original
customer cost less a 25% re-stocking charge. Custom orders do not apply.
FREIGHT POLICY
All orders will be shipped FOB Ontario, California, with a standard shipping
carrier selected by TOP un-less customer specifically requests their own
carrier and account. A freight quote may be requested in advance. TOP works
diligently with standard carriers to achieve the best discounts available.
THE OUTDOOR PLUS
701 S DUPONT AVE
ONTARIO, CA 91761
Contact Information:
Phone: (909) 460 5579
Sales: sales@theoutdoorplus.com
Support: support@theoutdoorplus.com
References
- Congratulations! You have successfully set up your website!
- Fire & Water Product Manufacturer | The Outdoor Plus
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>