Lasko 6405 CERAMIC OSCILLATING HEATER OPERATING MANUAL
- June 15, 2024
- Lasko
Table of Contents
Lasko 6405 CERAMIC OSCILLATING HEATER
IMPORTANT SAFETY INFORMATION
When using electrical appliances, these instructions and warnings should always be followed to reduce the risk of fire, electrical shock, and injury to persons:
Read all instructions before using this Heater.
WARNING
- ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT PLUG THE HEATER INTO ANY OTHER CORD-CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET ADAPTER, CORD REEL, OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.
- FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS TIGHTLY INTO THE OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER WITH ANY SOLID-STATE SPEED CONTROL DEVICES.
- Make certain that the power source conforms to the electrical requirements of the Heater.
- Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left operating unattended. Never leave children unattended when the heater is on or plugged in.
- This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
- DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use a Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres.
- Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner. To disconnect the Heater, turn the Heater OFF then remove the plug from the outlet.
- Always unplug the Heater when not in use. Unplug power cord before servicing or moving the Heater.
- Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
- Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug the power cord.
CAUTION
- Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover the Power Cord with throw rugs, runners, or similar coverings as this may cause cord to overheat. Arrange the Power Cord away from room traffic and where it will not be tripped over.
- This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use a handle when moving this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
- This Heater is not intended for use in wet locations. This Heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
- DO NOT use Heater outdoors.
- This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
- This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that changes and modifications made to the equipment
without the approval of the manufacturer could void the user’s authority to
operate this equipment.
Please contact Customer Service at
800-233-0268 Monday through Friday from
8 am to 5 pm EST for assistance.
OPERATION Figure 1
-
Carefully remove the Heater from the plastic bag and the carton.
-
Place the Heater on a firm and level surface.
Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors. -
Plug the cord set into a 120-volt outlet. Be sure that the plug fits tightly into the outlet.
When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater. -
When the Heater is initially plugged in, there will be a ‘beep’, indicating that there is the power to the unit. The power light will remain lit until the Heater is unplugged from the outlet.
-
Turn the Heater ON by pressing the Power Button.
-
When initially turned on, the Heater will be in High heat (1500 Watts) on Max. (The High light will be steady and the Max light will be blinking).
-
Press the Power Button once and the Heater will be in Low Heat, indicated by the steady light beside Low. The MAX light will be blinking.
-
Pressing the Power Button a third time will turn the Heater OFF.
-
Oscillation Function
Pressing the Oscillation Button (OSC) will allow the Heater to oscillate back and forth. To stop the oscillation, press the Oscillation Button (OSC) once again. The oscillation function will stop if the temperature function is in use and the heater turns off because the room has reached the desired temperature. The oscillation function will resume when the Heater turns back on. -
Temperature Function
To set the room at a specific temperature, press the Temperature Button to the desired setting. The light under the chosen temperature will continue to blink until the room reaches the desired temperature. For increased efficiency, the Temperature Function will only run on High heat. When set on MAX, the Heater will run continuously. -
Timer Function
The Timer Function may be activated when the Heater display is in any speed or temperature. This function allows you to set the length of time the Heater will run before turning itself off, from 1 hour to 7 hours. Pressing the Timer Button will increase the length of time, in combinations of 1, 2, and 4 hours. Continuously pressing the button will result in the timer being set for 7 hours. The Heater will turn off when the set time has elapsed. The unit can be turned back on by pressing the Power Button.
SAFETY FEATURE
- A thermal overload protector is built in to prevent overheating.
- If an overheating temperature is reached, the Heater will automatically shut off. It can only resume operation when the user resets the unit.
To Reset Heater:
- Unplug the Heater and wait 10 minutes for the Heater to cool down.
- After the Heater has cooled down, plug the unit into a 120V~ electrical outlet and follow the operation instructions described in this manual.
TROUBLESHOOTING TIPS
- Be sure the power cord is plugged into a working electrical outlet.
- Check your Temperature setting. The Heater may be off because it has reached the desired temperature setting.
- If your Heater runs for several minutes and shuts off repeatedly, your Heater may require cleaning. See the Maintenance section below.
If you have a problem that can not be resolved by the steps listed above, contact Technical Assistance at 1-800-233-0268, Monday through Friday, between the hours of 8 a.m. and 5 p.m. EST.
MAINTENANCE
Warning
- To reduce the risk of electrical shock and fire please observe the following instructions.
- Cleaning the Heater regularly will help to maintain its efficiency.
- Always unplug the cord before moving, servicing or cleaning.
- NEVER place the Heater in or near water. DO NOT IMMERSE HEATER IN WATER.
- Clean the Heater only with a vacuum equipped with a brush attachment; the vacuum will remove the lint and dirt from the surface of the Heater.
- Vacuum intake grills every two weeks; this will help to maintain the optimum Heater performance.
- Use a toothbrush or other soft bristle brush to gently loosen any dirt not removed by the vacuum.
- NEVER attempt to take apart the Heater.
- Clean the body of the Heater with a soft cloth only.
- NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other harsh cleaners.
SERVICING : For servicing, other than general user maintenance, please contact Customer Service at 800-233-0268, Monday through Friday, from 8am to 5pm Eastern.
STORAGE : Store the Heater with these instructions in the original carton in a cool, dry place.
LASKO PRODUCTS, INC. LIMITED WARRANTY (VALID IN THE USA, ITS TERRITORIES,
AND CANADA ONLY)
WHAT THIS WARRANTY COVERS: This product is warranted against defects in
workmanship and/or materials.
HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original
purchaser of the product and lasts for three (3) years from the date of
original purchase or until the original purchaser of the product sells or
transfers the product, whichever first occurs.
WHAT LASKO WILL DO: Lasko will, at its sole option, repair or replace any part or parts that prove to be defective or replace the whole product with the same or comparable model. For all warranty claims, the product must be returned to Lasko Products, Inc. at customer expense with proof of purchase within the warranty period. Contact the Lasko customer service department to obtain a Return Authorization (“RA”). DO NOT return products without an RA or the warranty claim will not be processed.
WHAT THIS WARRANTY DOES NOT COVER: This warranty does not apply if the
product was damaged or failed because of accident, improper handling or
operation, shipping damage, abuse, misuse, unauthorized repairs made or
attempted, or the use of the product for commercial or nonresidential service.
This warranty does not cover shipping costs for the return of products to
Lasko for repair or replacement. Lasko will pay return shipping charges from
Lasko following warranty repairs or replacement.
ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY IMPLIED WARRANTY OF MERCHANTABILITY), LAST THREE YEARS FROM THE DATE OF
ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR
TRANSFERS THE PRODUCT, WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL LASKO’S
LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY INCLUDE (I) INCIDENTAL OR
CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (II) REPLACEMENT OR REPAIR
OF ANY HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES. NOTWITHSTANDING ANYTHING
TO THE CONTRARY, IN NO EVENT SHALL LASKO’S LIABILITY UNDER ANY EXPRESS OR
IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH
LIABILITY SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD. Some
states and provinces do not allow limitations on how long an implied warranty
lasts, or the exclusion or limitation of incidental or consequential damages,
so these exclusions or limitations may not apply to you. This warranty gives
you specific legal rights. You may also have other rights which vary from
state to state and province to province.
Proof of purchase is required before a warranty claim will be accepted.
CUSTOMER SERVICE:
- Toll-Free 800-233-0268.
- Email: producthelp@laskoproducts.com
Our Customer Service team is available to assist you with product and service
questions, and replacement parts. They can be reached Monday through Friday, 8
am-5 pm Eastern. Please have your model number available, as well as the type
and style (located on the underside of your product).
Customer Service Dept., 820 Lincoln Ave., West Chester, PA 19380
(Please do not send the product to this location)
www.laskoproducts.com
PARTS FOR DISCONTINUED, OBSOLETE, AND CERTAIN OTHER PRODUCTS MAY NOT BE
AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS AND MOST HEATER
COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT.
FAQs
Question: Is the Lasko 6405 heater safe to use?
Answer: Yes, the Lasko 6405 comes with safety features such as overheat protection and a cool-touch exterior, making it safe for use in homes with children and pets.
Question: Can I control the oscillation feature of the Lasko 6405?
Answer: Yes, you can control the oscillation feature, allowing you to choose whether you want the heater to rotate and distribute heat in a wider area or stay stationary.
Question: Does the Lasko 6405 heater have a timer function?
Answer: No, the Lasko 6405 does not come with a built-in timer function.
Question: How do I clean the Lasko 6405 Ceramic Oscillating Heater?
Answer: To clean the heater, unplug it and use a soft brush or vacuum cleaner to remove dust from the grill and surrounding areas.
Question: Is the Lasko 6405 heater suitable for use in a bedroom?
Answer: Yes, the Lasko 6405 is a quiet heater, making it suitable for use in bedrooms.
Question: Can I use the Lasko 6405 heater in a bathroom?
Answer: No, the Lasko 6405 is not designed for bathroom use, as it is not moisture-resistant.
Question: What is the warranty period for the Lasko 6405 heater?
Answer: The warranty period for the Lasko 6405 varies, but it is typically covered by a 3-year limited warranty.
Question: Can the Lasko 6405 Ceramic Oscillating Heater be used as the primary heating source in a larger room?
Answer: The Lasko 6405 is best suited as a supplemental heating source for smaller to medium-sized rooms. It may not be sufficient as the primary heating source for a large room or an entire home.
Question: Does the Lasko 6405 heater have adjustable heat settings?
Answer: Yes, it has multiple heat settings, including high and low settings, allowing you to customize the level of warmth.
Question: What is the heating capacity of the Lasko 6405 heater?
Answer: The Lasko 6405 can produce up to 1,500 watts of heat, making it suitable for heating rooms of various sizes.
Question: How does the Lasko 6405 Ceramic Oscillating Heater work?
Answer: The Lasko 6405 heater uses ceramic heating elements to generate and distribute heat. It features an oscillating fan that helps evenly distribute warm air throughout the room.
Question: What is the Lasko 6405 Ceramic Oscillating Heater?
Answer: The Lasko 6405 Ceramic Oscillating Heater is a portable electric space heater designed to provide warmth and comfort in small to medium-sized rooms.
Download This Manual PDF:Lasko 6405 CERAMIC OSCILLATING HEATER OPERATING MANUAL
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>