DEREAL Lithium 2 In 1 Mini Electric Chainsaw Cordless Instructions

DEREAL Lithium 2 In 1 Mini Electric Chainsaw Cordless

Thank you for choosing this product, to ensure your safe use, please read the instructions carefully before use, and keep the instructions

Description of products

1. Chain guard
2. Auxiliary handle
3. Tighten the knob
4. Sprocket cover
5. Trigger lock
6. Protection plate
7. Bar
8. Chain
9. Switch trigger
10. Left and right handle
11. Charger
12. Battery

Technical specification

Basic Information of Lithium single-hand saw

• Model no DCCS2106B
• Operation voltage 20V
• Charger input voltage 11 0V-50/60Hz
• Bar 6″ and 8″

Install bar and chain

• Please cut off the Battery before adjusting the chain tensioning.
• Turn out the tensioning knob counterclockwise (Figure 1) and remove the sprocket cover from the body.
• If it is a used machine, please clean the residual wood chips and debris on the chain cover in time to ensure the accuracy of the assembly when installing the guide chain in the next step.
• Take out the guide plate and chain and check the cutter teeth of the chain before installing the chain on the guide plate.
• The cutter teeth need to be installed on the guide plate as shown in Figure 2.
• After the chain is installed on the guide plate, please place the guide chain installed together vertically, with one end of the guide wheel on it, and pull the chain by hand for a week to check whether the slide is smooth.
• Note: When the machine has been used for a while, it is best to check the guide and chain according to the above method before each use, if it is not smooth, it may need to replace or repair the guide and chain.
• Put the chainsaw in a stable place, install the installed guide and chain on the machine, and hang the teeth on the inside of the chain to the drive sprocket (Figure 3).
• Cover the sprocket cover, pay attention to the cover, the hand should hold the guide plate and chain, to prevent the chain from slipping out of the sprocket, screw the tensioning knob above the stud, and use a Phillips screwdriver to adjust the screw clockwise (as shown in Figure 4), to adjust the lightness between the guide plate and the chain, and then turn the tensioning knob clockwise to press the sprocket cover, the guide chain installation is complete.
• Before using the chain saw, after the first use and about 10 minutes during regular use, check the tightness of the chain to ensure that the appropriate tightness of the chain is achieved.
• Note: Put on protective gloves, pinch the chain, drag it back and forth to see if the sprocket and chain are toothed, and then turn the adjusting screw clockwise to tighten the chain, the best tightness of the chain is controlled at 2~4mm distance (as shown in Figure 5).
• Use and operate the chainsaw as shown in Figure 6. Lubricate the guide and chain with 32# anti-wear lubricating oil. Do not use the machine without lubrication.

Install the battery pack

• After confirming the battery pack’s power level, align the card slot of the battery pack with the card tendon of the machine and insert it into the battery compartment of the machine (as shown in Figure 7).
• After the correct insertion, the battery is locked on the machine and cannot be pulled out directly.
• The battery pack is installed successfully.
• Note: To extend the service life of the battery pack, please fully charge the battery pack before placing it.
• If you do not use the machine for a long time, it is recommended to charge it every 3 months.

Charging the battery pack

• Connect the power plug of the charger to the power outlet. At this point, the charger indicator light is red, indicating that the charger is charging,
• The charger indicator light is green, indicating that the charging operation is complete (Figure 8).

Battery packs and chargers are used safely

• Charge only using the charger specified by the manufacturer. A charger used in conjunction with another battery pack may pose a fire hazard.
• Only use power tools with specially designated battery packs. Using other battery packs can result in injury and fire.
• When not using the battery pack, keep it away from other metal objects, such as paper clips, coins, keys, nails, screws, or other small metal objects that may cause a connection between one terminal and another. A short circuit in the battery terminal may cause burns or fire.
• In harsh conditions, liquid may be expelled from the battery, please avoid contact, if accidental contact, please wash immediately with water. If fluids come into contact with your eyes, seek medical help immediately. The liquid ejected from the battery may cause irritation or burns.
• Charging state, do not use tools. Be sure to charge the tool indoors, away from heat sources, and avoid covering the charger and battery pack, which may cause poor heat dissipation and damage to the tool.
• Charge the battery pack immediately after discharge. Storage tools should be in a state of excess electricity, away from high temperatures, and choose a cool, dry area.
• The battery pack has a self-discharge phenomenon, if not used for a long time, it is recommended to charge once every 6 months, when the power is insufficient, do not force use.
• The battery pack must be charged after continuous use for a specified time, and the forced use of the weak state seriously affects the performance of the battery pack product.
• Do not use damaged or modified battery packs or tools. Damaged or modified batteries may exhibit unpredictable behavior that can lead to fire, explosion, or injury hazards.
• Do not allow the battery pack or tools to catch fire or overheat. Fire or temperatures above 130C May cause an explosion.
• Follow all charging instructions, and do not charge the battery pack or tool outside the temperature range specified in the instructions.
• Incorrect charging or charging at temperatures outside the specified range can damage the battery and increase the risk of fire.

Knowledge of battery packs and chargers

• The power input voltage of the charger is 220V~50HZ
• Do not allow any liquid into the charger, battery pack
• The charger and battery pack of the same specification and model of the original manufacturing factory must be used
• The charger and battery pack should not be used in the rain or wet environment
• Do not hit or damage the battery pack, and do not use a battery that will be damaged by impact
• The charger and battery pack will heat up during the charging process. Pay attention to keeping the working environment of the charger ventilated
• Keep chargers and battery packs clean
• The discarded battery pack should not be burned or discarded at will and should be placed in the designated recycling area.
• Note: Do not cover tool vents, tools naturally cool during use

Lithium battery high branch telescopic rod manual

Announcements:

• Do not use the device in the following situations

1. Slippery ground or ground that has the potential to cause a person to slip.
2. At night, in foggy weather, or when the line of sight is not clear in a safe area where the device is used.
3. Rain, snow, wind, thunder, or other dangerous weather conditions.

• For the first time, you should find an open, bright, and empty place, connect the equipment, and carry out no-load practice until you are sure that you can use the machine well, and then start the actual operation.
• Excessive fatigue can reduce concentration and cause accidents. The continuous working time of each machine operation should not exceed 10~20 minutes.

Clothing and equipment for use:

• The use of lithium battery high-branch telescopic rods should pay attention to wearing suitable outdoor work clothing and wearing the following equipment.

1. Work cap
2. Dust glasses or face shield
3. Strong insulating gloves
4. Shoes that are not slippery and have an insulation effect
5. Earplug

Precautions before use

• Before proceeding, familiarize yourself with the situation of the workplace (terrain and trees to be repaired, nearby obstacles) and remove any obstacles that can be removed.
• Within 5 meters from the operator is a dangerous area, no personnel are allowed to enter or leave.
• When more than two people work at the same time, a safe distance should be maintained between each other to avoid accidents.
• Check the machine carefully before starting to ensure that the connection is strong and the power supply and the machine are not abnormal.
• In particular, it is necessary to carefully check the installation part of the high branch telescopic rod and the equipment.

Brief introduction of the function:

1. Battery pack jack
2. Switch
3. Switch trigger lock
4. Belt
5. Sponge tube for hand protection
6. Clamp CAM wrench2
7. Angle lock button
8. To release the latch
9. Tool connection jack
10. Tool lock
11. Clamp the trimmer nut 1
12. Clamp the trimmer nut 2

Applicable product specifications:

The lithium battery high branch telescopic rod is suitable for the Makita lithium battery interface tool ( Applicable to our series of products )

1. Brushed one-hand lithium chainsaw 4” and 6′ bar.
2. Brushless one-hand lithium chainsaw 6” and 8’bar.
3. Lithium electric scissors 3.0—4.0

Operating instructions:

1. Insert the required lithium battery single bracelet saw or lithium battery scissors into place according to the direction shown in Figure 1, and The tool lock can be heard to make an obvious clack” sound
2. Push the release latch up into place in the direction indicated in the figure
3. Take the lithium battery pack and insert it into place as shown in the direction of Figure 3, and the battery pack lock will emit a “clack”.
   • Acoustic battery pack installed in place 4)
4. Press the trigger lock to turn the trigger device normally
5. Install the lithium scissors according to steps 1. 2. 3 above. Press and hold the power button of the lithium scissors before the operation
   • The device wakes up after three beeps. Press the handle trigger lock to turn the trigger device normally

Scaling operation instruction:

1. Move the tightening CAM wrench outward, as shown in Figure 1, and the second telescopic rod can be pulled out Length, the tightening CAM wrench can be moved back to the original position. As shown in Figure 2
2. Repeat the operation method of 1. To adjust the required length of the third telescopic rod.
3. The telescopic rod is retracted to a minimum size of 1.48 meters, the second section is fully extended to a maximum of 2.35 meters, and the three sections are fully extended The total length is 3.18 meters. Does not include a battery pack, lithium battery tools
4. The telescopic rod can be retracted by repeating the steps in Figure 1 and then locked according to the steps in Figure 2
5. When the telescopic rod is loose and cannot be completely clamped, rotate the fine-tuning nut.

  * Turn clockwise for clamping, if the clamping CAM wrench does not move to the inner plate, Or very hard to rotate the fine nut counterclockwise to loosen the clamp.

Angle rotation operation instructions:

1. Press the Angle lock button and rotate the connecting seat to adjust the connected tool to the appropriate Angle. As shown below:
2. Adjust the range to the telescopic rod axis direction to adjust the tool to 0 degrees. 30 degrees, 60 degrees, 90 degrees, minus 30 degrees, 60 degrees, 90 degrees.

Safety warning – Maintenance:

• This product uses metal tubes to make telescopic, high-altitude use away from high voltage lines.
• This product is attached to lithium electric tools, if there is a problem, the telescopic rod will be sent to professional maintenance personnel, using the same parts for repair

Lithium single-hand saw

Manufacturer certificate

• Model no———————————–
• Production date: ——————————–
• Inspector:———————–
• This product is approved for delivery after passing the inspection

User save link

When the warranty is requested, valid documents for the purchase of the machine must be provided

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>