UREVO URTM024 Spacewalk 3S Walking Treadmill User Manual

UREVO URTM024 Spacewalk 3S Walking Treadmill

CUSTOMER SERVICE

IMPORTANT: FOR UREVO ONLY For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department by the below methods:

• services@urevosports.com.
• Response Time: 24-48 hours
• Emailing us with the Order ID will be the best method to receive a response during peak business hours.
• Website: www.urevosports.com.
• US Support Hotline: (1)844-998-2473
• Hours of Operation:
• Monday – Friday : 9 AM – 12 PM; 1 PM – 6 PM (PST)
• PLEASE DO NOT RETURN THIS PRODUCT WITHOUT
• ASKING OUR CUSTOMER SERVICE FIRST.

SCAN THIS QR CORD TO GET THE PRODUCT INSTALLATION OR MAINTENCE VIDEOS

IMPORTANT SAFETY INSTRUCTIONS

DANGER – To reduce the risk of electric shock: Always unplug this appliance from the electrical outlet immediately after using and before cleaning.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. An appliance should never be left unattended plugged in. Unplug from outlet when not in use,and before putting on or taking off parts.
2. Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
3. Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons.
4. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
5. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
6. Do not carry this appliance by supply cord or use cord as a handle.
7. Keep the cord away from heated surfaces.
8. Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.
9. Never drop or insert any object into any opening.
10. Do not use outdoors.
11. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
12. Caution – To reduce the risk of injury from moving parts – Unplug before servicing.
13. Warning – To reduce the risk of Electric shock – Unplug before cleaning or servicing.
14. Warning – Risk of personal injury – Keep children under the age of 13 away from walking treadmill.
15. To disconnect, turn all controls to the position, then remove plug form the outlet.
16. Connect this appliance to a properly outlet only. See grounding instructions.
17. This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been aiven supervision or instruction concerning use of the appliance by a person responsible for their safety. Keep children under the age of 13 away from this walking treadmill.
18. The maximum weight capacity for this product is 264.5 lbs/120kg. DO NOT EXCEED MAXIMUM WEIGHT CAPACITY. SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electricity and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded by all local codes and ordinances.
DANGER – Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
FCC STATEMENT:
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
3. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with RSS210 of Industry Canada. This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device. appareils radio exempts de licence.

Son functionnementestsujet aux deux conditions suivantes:

Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This Class B digital apparatus complies with Canadian ICES-00

SAFETY NOTICE

SPECIFICATION

Performance indictors| Detailed parameters| Performance indictors| Detailed parameters
---|---|---|---
Product dimension| 131x 56.2 x 16.5 cm| ****

Net weight

| 27 kg
51.6 x 22.1 x 6.5 inch| 59.5 lbs
Walking area| 108 x43 cm| ****

Gross weight

| 33.2 kg
42.5 x 16.9 inch| 73.19 lbs
Maximum load| 120 kg| Rate voltage| 110 – 120V ~
265Ibs| Rated power| 600W
Maximum speed| 4mph| Peak horsepower| 2.5Hp
Minimum speed| 0.6 mph| Suggested age| 14-60 years old
Maximum incline percentage| Upto 9%| I

PRODUCT AND ACCESSORIES

Please carefully check whether the contents of the package are complete and intact. If there is any missing and damage, please contact the seller.

PRODUCT INTRODUCTION

BEFORE START AND STORAGE

Take out appliance from packages.

1. Unbox and take out accessory box.
2. Lift out appliance and place at flat surface.
   • Attention: 2-3 persons assist is necessary.
3. Its normal that visible welding marks residual on walk belt.

Transportation

1. If transportation needs, unplug power 12 cord and lifting the terminal of appliance
2. Easy to transport appliance with bottom transportation wheel assists, like as wheelbarrow.

Connect the power

1. Choose flat ground to place the Walking Treadmill. Do not place it on a thick and soft cushion.
2. Plug in the power cord and switch on the power rock button, you can hear a BI sound from the buzzer, its means the circuit of the appliance has connected with power electricity. Warning: MUST use the power cord with comes of package.
3. Storage: Power off the appliance and unplug the power cord before the storage process.

DISPLAY SCREEN

INC.

Speed

| 00-9

0.6-4.0 mph

| Displays the incline of tilt

Displays the speed of walking belt.

Time| 0:00-99:59 minutes| Displays the elapsed time.
Distance| 00.0-99.99 miles| Displays the distance that you have walked or run.
Kcal

|  | 0-6553 Kcal| Displays the approximate number of calories you have burned.
ERP indicator light| I| Device hi?ernation, with an interval of 5 seconds and a duration of 0.3 seconds for each light-up (E indicator light brightness is 50% of normal brightness).
Bluetooth| I| Display connection status.
Startup display| V 0~9.0~9| “Vx._x” displayed during startup represents the current hardware application version of the product.

REMOTE CONTROL

Romote control can be stored in side of body as shown figure.

HOW TO USE

Note: Ensure that the walking treadmill is power on and the remote control is installed with battery.

1. Operation of Remote Controller
2. Auto incline feature introduction
   • 9 incline levels: 0°~9°
   • approxn 1% inline percetange
   • Change the incline of working treadmill as desired.

Friendly remind of Auto incline features

• Incline level should be set to ” Zero” with remote control when you are finished exercising.
• Perform POST (Power On Self Test) to identify incine level and back to ” Zero” automatically.
• Incline interval up to 10 seconds, total incline stroke ” from Zero to Level 9″ approximately 1 minute.

ERROR CODE

• When error occurs, error warning indicator will light up and display its error code.

Error Code I Fault Analysis I Resolutions

E01| Communication was interrupted between the controller and numeric display.| Unscrew the motor hood and verify the connection between the controller and the numeric display.

Please contact with after-sale service if the E01 code has not been eliminated.

Notice: Always power off and unplug the power cord before processing.

E02| open circuit of the motor| 1.  User confirms whether the motor wires are securely plugged in the lower control board.If the connection is loose or contact is poor, tighten the terminal and reinsert it into the controller.

2.  Please contact with after-sale service if the problem CAN NOT solved by above process.

E03| Flame protection| 1.  Unscrew motor hood and verify the connection between controller and motor.

2.  Power supply interrput due to connector loosen or out, please unscrew motor hood to check.

3.  Please contact with after sale service if problem CAN NOT solved by above process.

E04| Over current protection| 1.  Due to user over limited 120Kg.

2.  Open to check any foreign objects blocked moving parts. ( such as: drive motor, idler roller, driver roller, walking belt)

3.  Walking belt is overtightened or lack of lubricant. ( please see detail chapters relate to belt tension and lubricant process)

E08

| Communcation interrupted between signal cable and console.| 1.  Unscrew console box and verify connection between singal cable and console.

2.  Unscrew console box and verify internal lead wires whether are damaged or pierced.

3.  Replace new console PCBA board.

TROUBLESHOOTING

No working

|

1.  Power rock switch dysfunction.

2.  Power supply interrupted.

3.  Power cord damaged.

| 1.  Replace new power rock switch if it doesn’t light on.

2.  Make sure that power cord is plugged into properly grounded outlet.

3.  Replace the new power cable.

Walking belt slips

|

The walking belt loosened.

| Tighten the walking belt tension with hex tool. (See details of chapter 13-A)

Remote control does not work

|

1.  Incorrect use of default.

2.  Battery power shortage.

3.  Remote control malfunction.

| 1.  Remotor control should directly aiming to receiver port when in use.

2.  Replace new battery cells.

3.  Replace new remote control.

The incline   doesn’t work

| 2.  Incline motor dysfunction.

3.  Incline mechanism damaged.

| Contact with after-sale service to replace inline motor or gear box.

CARE AND MAINTENANCE

A. Symptom: walk belt off-centre or slips.

The centering walk belt process as follows:

1. Power off the appliance and unplug the power cord
2. The manual centering process as follow:
   • If the walk belt has shifted to left, use the hex tool to turn the left idler roller screw clockwise 1/4 of a turn(refer to Figure 1).
   • If the walk belt has shifted to right, use the hex tool to turn the right idler roller screw clockwise 1/4 of turn(refer to figure 2).
3. Appliance MUST work 1-2 minutes. Repeat the manual centring process until the walk belt is centred.

Belt slip-correcting process as follows:

1. Power off the appliance before operation.
2. Using the hex tool, turn both idler roller screws clockwise 1/2 of turn (refer to figure 3).
3. After correcting, please attempt to walk for 1-2 minutes under 1.0mph speed setting. Repeat until the walk belt is properly tightened.

Attention

1. To prevent any injury, don’t place any debris around the appliance before the maintenance process.
2. MUST use the associated hex tool.
3. Take care at the maintenance process. Do not pinch your fingers.

B. Belt lubrication process, follow the instructions below to lubricate the belt.

1. Power off the appliance and unplug the cord.
2. Using the hex tool, turn both idler roller screws counterclockwise till the belt loosen and lifting easily.
   • Tips: please mark hex tool rotating cycles when loosening the belt, which is used for adapting belt tension after the lubrication process.
3. Lifting edges of the belt and spraying lubrication oil at the centre of the walking platform evenly. Not necessary to apply spray lubrication oil on entire walk platform.
4. Lubrication oil volume Per time of maintenance: 5-10mL.
   • Attention: it would cause of belt slip if spray too much.
5. Using the hex tool, turn both idler screws clockwise as previous markdown number of turns until the walk belt tightens properly.
6. Power on the appliance and work out for a few minutes, to spread lubrication oil to the whole belt surface evenly. Lubrication frequency: High recommend 125 Miles Per time.

C: Appliance cleaning.

1. Power off the appliance and unplug the power cord before cleaning.
2. Wipe and clean with a damp cloth, Do not clean with acidic or caustic detergents.
3. Do not clean the opposite of the walk belt.
4. Its normal few black powders are residual under the appliance after a long working.

WARRANTY

MANUFACTURER’S LIMITED WARRANTY
UREVO warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with UREVO Owner’s Manual. UREVO’s obligation under this warranty applies to the following:
COMPONENT LENGTH OF WARRANTY
Structural Frame 1 year For Home Use Only All Other Components 90 days For Home Use Only Exclusions from Warranty Coverage: UREVO does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any product failure, product malfunction, or damages attributable to:

1. Improper installation and/or failure to abide by UREVO’s installation guidelines;
2. Use of this product beyond normal home use, or in an application for which it was not designed;
3. Cosmetic items such as scratches, dents or discolourations;
4. Damage caused by normal wear and tear, vandalism, accidental or by animals;
5. Any act of Nature (such as fire, flooding, snow, ice, hurricanes, earthquakes, lightning or other natural disasters), environmental condition (such as air pollution, mould, mildew, etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);
6. Normal weathering is due to exposure to sunlight, weather and atmosphere which can cause colored surfaces to among other things, flake, chalk, accumulate dirt or stains.
7. Improper operation, alteration, handling, storage, abuse or neglect of the products.

UREVO, using its sole discretion, will either repair or replace free of charge any parts) proven to be defective under normal home use. Any repair or replacement shall provide no new warranty coverage but shall retain only the remaining portion of the original product’s warranty. This warranty is offered only to the original purchaser and is not transferable. Proof of original purchase is required.
When ordering replacement parts please have the following information ready:

1. Order Number
2. Description of Parts (Adding photos or videos would be helpful)
3. Part Number
4. Date of Purchase

IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference. The specifications of this product may vary from this photo, subject to change without notice.

CONTACT

• Manufacturer: Shenzhen Vile Dynamic Technology Co., LTD.
• Address: 1205-1206, Tianliao Building, Tangchang Road, Tanglang
• Community, Taoyuan Street, Nanshan District, Shenzhen, China
• Version: 2.0
• Model. URTM024

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>