KALOR TECH AC603H Wi-Fi Thermostats and Accessories Instruction Manual

: June 15, 2024
: KALOR TECH

Table of Contents

KALOR TECH AC603H Wi-Fi Thermostats and Accessories
Product Information
Product Usage Instructions
TOOLS REQUIRED
NEW THERMOSTAT PREPARATION
INSTALLATION
RESTORE POWER AND TEST
HOME SCREEN
REMOTE MANAGEMENT SETUP
ADDING A THERMOSTAT TO THE ALEXA DEVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KALOR TECH AC603H Wi-Fi Thermostats and Accessories

Product Information

Specifications

Wireless Connectivity: 2.4 Ghz Wi-Fi
Voice Assistant Compatibility: Alexa or Google Assist
Smartphone or Tablet Requirement: Yes

Product Usage Instructions

New Thermostat Preparation

Turn off power at the electrical panel for this unit.
Do not attempt installation without turning off the power.
Unscrew the plate of the thermostat to be replaced and take note of the cabling. Take pictures and label cables if necessary.
Insert the KALOR TECH wall plate into the back of the new thermostat, ensuring that the 6 raised tabs on the wall plate make contact with the back of the thermostat’s metal plate.
Using a small, sloped screwdriver, loosen the screws on the underside of the back of the thermostat corresponding to numbers 1, 2, 3, and 4.
Insert the BLACK pigtails into slots 1 and 4. Tighten the screws and ensure the cables cannot be pulled. Do not overtighten, but you should be able to tug on the cable when it is secured.
Repeat the process for slots number 2 and 3 using the RED pigtails.

Installation

Please observe the diagram to install your device using the provided pigtails. The pigtails in ports 1 and 2 connect to the baseboard heater cables (load), while the pigtails in ports 3 and 4 connect to the power source cables (line).

Restore Power and Test

Turn on power at the main panel. If properly installed, the thermostat should display the temperature, and the power button at the center of the thermostat should glow orange.
Using the up and down arrows, try raising the temperature by a few degrees and ensure your baseboard heater responds.
Test by turning off the thermostat, waiting a few minutes, and checking if your baseboard heater has cooled off.

Home Screen

ON-OFF Button: Short press to turn on or off
MODE Button: Short press for manual or program mode
Clock: Short press for time setting
Up arrow: Increase parameters for a given setting
Down arrow: Decrease parameters for a given setting

Thank you for choosing KALOR TECH. We provide you with exceptional tools to help you take control of your hyang at home or from anywhere in the world, and to allow you to save money, achieve maximum comfort, and experience peace of mind. PLEASE DO NOT RETURN THIS UNIT un l we have had an opportunity to assist you. Email us at sales@kalortech.ideasolver.com for support. We respond to inquiries quickly and most likely provide a resole on to your issue. You can also ﬁnd these instructors online at our website.
https://www.kalortech.ideasolver.com

This booklet covers the following topics

Requirements for install on
New thermostat preparator
Physical install on and tens
Wireless conicity for remote management

TOOLS REQUIRED

Small, soled screwdriver
Small, Phillips screwdriver
Cable stripper (optional)
Voltmeter (optional)
Wire nuts

WIRELESS FEATURES (optional)

2.4 Ghz Wi-Fi network (only required for device install on)
Voice assistant such as Alexa or Google Assist
Wi-Fi network access for voice assistant management
Smartphone or tablet, (optional, but necessary for remote management)

NEW THERMOSTAT PREPARATION

Turn power off at the electrical panel for this unit. DO NOT attempt to install this device without turning the power off from the main panel!
Unscrew the plate to the thermostat you’re about to replace and take note of the cabling. Take pictures and label cables if necessary.
Insert the KALOR TECH wall plate into the back of the new thermostat, ensuring that the 6 raised tabs on the wall plate make contact with the back of the thermostat’s metal plate.
Using a small, slotted screwdriver, loosen the screws on the underside of the back of the thermostat corresponding to numbers 1,2,3 and 4.
Insert the BLACK pigtails into slots 1 and 4. Tighten the screws and ensure the cables cannot be pulled. Do not overtighten, but you should be able to tug on the cable when it is secured..
Repeat the process for slots number 2 and 3 using the RED pigtails.

INSTALLATION

Please observe the diagram to the right to install your device using the pigtails provided.

The pigtails in ports 1 and 2 connect to the baseboard heater cables (load).
The pigtails in ports 3 and 4 connect to the power source cables (line).

RESTORE POWER AND TEST

Turn the power on at the main panel. If properly installed, the thermostat should display the temperature and the power bouton at the center of the thermostat should glow orange.
Using the up and down arrows, try raising the temperature by a few degrees. Ensure your baseboard heater responds.
Test by turning oﬀ the thermostat, awing a few minutes, and checking to see if your baseboard heater has cooled oﬀ.

HOME SCREEN

ON-OFF Button Short press to turn on or off
MODE Button Short press for manual or program mode
Clock Short press for time setting
Up arrow to increase parameters for a given setting
Down arrow to decrease parameters for a given setting

REMOTE MANAGEMENT SETUP

From the Google Store or Apple Store, download and install either the Toya or Smart Life apps. Alterna vely, scan the QR code on Page 1 to easily ﬁnd the app.
Once installed, open the app and create a new account or sign in if prior devices had been added to the account. To connote, please ensure your wireless network can emit a 2.4 Ghz signal to add devices.
Alternately, a hotspot from a second phone can be used.
NOTE : This is only required for the device installation. Ordinary management of the device occurs through your preferred Wi-Fi network.
In the app, click the Add Device icon (+) to add a device to ﬁnd.
Select Small Home Appliance from the categories on the . Scroll down and choose Thermostat (Wi-Fi) from the choices.
The app should show the name of your 2.4 Gaz network(s) or phone hotspot. Enter the password for such a network and click Next .
On the device, hold the Mode and the Up arrow simultaneously un l the Wi-Fi icon begins to blink.
On the app, conﬁrm that the Wi-Fi indicator is blinking. If so, choose Blink Quickly .
Aer 2 minutes or less, the app should ﬁnd the device.
The app will now show the new device and a suggested name, which you can change on the next screen. Select Done . To the right of the name, a pencil icon allows you to change the name. The name should reﬂect the loca on of the device. This name will also be used when giving voice commands to Alexa or Google Assistant.
Aer successfully adding the device, your list of manageable devices should display. You can now open the new device to begin managing from anywhere, such as raising the temperature, using the digital dial, changing to manual or program , enabling the child lock, etc.
At this point, you may reconnect the phone or tablet to the preferred network.

ADDING A THERMOSTAT TO THE ALEXA DEVICE

Open the Alexa app on your smartphone or tablet.
From the “hamburger” menu, select Skills & Games . On the top right, select the magnifying glass to search and enter the name of the applicant you installed on Page 5, Toya or Smart Life .
Once found, select it to link to your Alexa account.
Select Enable to Use if this is the ﬁrst me using it. You’ll need to provide your or Smart Life username and password for Alexa to be able to manage the devices.
Aer entering the login inform on, select Authorize .
You should receive a message such as “Smart Life has been successfully linked”. Click on Done .
Click the op on to Discover Devices. a brief moment, the new device should show up. If no device is found, close the Alexa app and wait a few minutes, relaunch the Skills and Games op ons and reopen the Tuya or Smart Life applicants.
Once found within Alexa, you may use voice commands to control your thermostat.
For a list of common commands or to view a step-by-step video of the install on steps , go to the Alexa Commands sec on of the KALOR TECH website at kalortech . ideasolver.com , where you may download these imaterial.