KALOR TECH 603H Wi-Fi Thermostats and Accessories Instruction Manual

KALOR TECH 603H Wi-Fi Thermostats and Accessories

Product Information

The product being discussed is a thermostat manufactured by KALOR TECH. The thermostat can be connected to a 2.4 GHz Wi-Fi network and can be controlled using a voice assistant like Alexa or Google Assist. The device can also be remotely managed using a smartphone or tablet. The thermostat comes with a wall plate that needs to be inserted into the back of the new thermostat before installation. The device requires a physical installation and comes with a set of required tools, including a small and sloped screwdriver, a small Phillips screwdriver, a cable stripper (optional), a voltmeter (optional), and wire nuts.

Product Usage Instructions

Before installing the new thermostat, turn off the power from the main electrical panel. Unscrew the plate from the old thermostat and take note of the cabling. Insert the KALOR TECH wall plate into the back of the new thermostat, ensuring that the 6 raised tabs on the wall plate make contact with the back of the thermostat’s metal plate. Using a small sloped screwdriver, loosen the screws on the underside of the back of the thermostat corresponding to numbers 4, 3, and 1.

Insert the BLACK pigtail into slot 4. Tighten the screw and ensure that the cable cannot be pulled. Repeat this process for slot number 1 using a BLACK pigtail and for number 3 using the RED pigtail. Using wire nuts, attach the pigtail from slot 4 to the hot (live) wire (usually BLACK) in the box. Attach the number 3 (RED) pigtail to the neutral wire in the box (usually WHITE). Attach the number 1 pigtail to the load wire (usually BLACK) leading to the heater. Once all connections are tightly secured, push all cables in the box to make room for the back of the thermostat, and push the device back into the wall plate/electrical box. Restore power from the main panel and test the thermostat. The thermostat should display the temperature, and the power button at the center of the thermostat should glow orange. Using the up and down arrows, try raising the temperature by a few degrees. Ensure that your baseboard heater responds. Test the thermostat by turning it off, waiting a few minutes, and checking to see if your baseboard heater has cooled off.

The thermostat also has a home screen that includes an on-off button, a mode button, and a clock. You can use the up and down arrows to increase or decrease parameters for a given setting. The device can also be remotely managed using a smartphone or tablet. To set up remote management, download and install either the Tuya or Smart Life apps from the Google Store or Apple Store. Once installed, create a new account or sign in if prior devices had been added to the account. In the app, click the Add Device icon (+) to add a device to find. Select Small Home Appliance from the categories on the left and choose Thermostat (Wi-Fi) from the choices.

WARNING: This product should only be installed by a qualified electrician or installer experienced with high voltages and electrical devices. If you are unsure about any aspect of the installation, please consult a professional. KALOR TECH assumes no responsibility for injury due to negligence, improper installation, or deviation from the recommended installation method. Please observe electrical codes for vour area. Visit us at KALORTECH.IDEASOLVER.COM

Thank you for choosing KALOR TECH. We provide you with exceptional tools to help you meet your goals, while achieving maximum comfort and peace of mind, whether you control your devices from the comfort of vour sofa via voice commands through your Alexa or Google Assist devices, or from the other side of the world on your easy-to-use Tuya or Smart Life app. PLEASE DO NOT RETURN THIS UNIT until we have had an opportunity to assist you. Email us at sales@kalortech.ideasolver.com for support.

This booklet covers the following topics:

• Requirements for installation
• New thermostat preparation
• Physical installation and testing
• Wireless connectivity for remote management

TOOLS REQUIRED

(PHYSICAL INSTALLATION)

• Small, slotted screwdriver
• Small, Phillips screwdriver
• Cable stripper (optional)
• Voltmeter (optional)
• Wire nuts

WIRELESS FEATURES

(optional)

• 2.4 Ghz Wi-Fi network (only required for device installation)
• Voice assistant such as Alexa or Google Assist
• Wi-Fi network access for voice assistant management
• Smartphone or tablet, (optional, but necessary for remote management)

THERMOSTAT PREPARATION

NEW THERMOSTAT PREPARATION

1. Turn power off at the electrical panel for this unit. DO NOT attempt to install this device without turning the power off from the main panel!
2. Unscrew the plate to the thermostat you’re about to replace and take note of the cabling. Take pictures and label cables if necessary.
3. Insert the KALOR TECH wall plate into the back of the new thermostat, ensuring that the 6 raised tabs on the wall plate make contact with the back of the thermostat’s metal plate.
4. Using a small, slotted screwdriver, loosen the screws on the underside of the back of the thermostat corresponding to numbers 4, 3, and 1.
5. Insert the BLACK pigtail into slot 4. Tighten the screw and ensure the cable cannot be pulled. Do not over tighten, but you should be able to tug on the cable when it is secured..
6. Repeat the process for slot number 1, using a BLACK pigtail, and for number 3 using the RED pigtail.

INSTALLATION

1. Using the required wire nuts, attach the pigtail from slot 4 to the hot (live wire (usually BLACK) in the box.
2. Attach the number 3 (RED) pigtail to the neutral wire in the box (usually WHITE).
3. Attach the number 1 pigtail to the load wire (usually BLACK) leading to the heater. Ensure all connections are tightly secured. Verify connections. Push all cables in the box to make room for the back of the thermostat, and push the device back into the wall plate/electrical box.
4. While holding the plate against the wall, carefully pull the thermostat away from the wall plate. Using a Phillips screwdriver, secure the wall plate to the electrical box using the longer 6/32 screws. Now, hold the body of the thermostat and push the casing upward to open the device, allowing you to secure the back of the thermostat to the wall plate using the small Phillips screws provided. DO NOT overtighten. Once in place, slide the thermostat casing downward against the back to snap in place.

RESTORE

RESTORE POWER AND TEST

1. Turn the power on at the main panel. If properly installed, the thermostat should display the temperature and the power button at the center of the thermostat should glow orange.
2. Using the up and down arrows, try raising the temperature by a few degrees. Ensure your baseboard heater responds.
3. Test by turning off the thermostat, waiting a few minutes, and checking to see if vour baseboard heater has cooled off.

HOME SCREEN

• ON-OFF Button Short press to turn on or off
• MODE Button Short press for manual or program mode
• Clock Short press for time setting
• Up arrow to increase parameters for a given setting
• Down arrow to decrease parameters for a given setting

REMOTE MANAGEMENT SETUP

1. From the Google Store or Apple Store, download and install either the Tuya or Smart Life apps. Alternatively, scan the QR code on Page 1 to easily find the app.
2. Once installed, open the app and create a new account or sign in if prior devices had been added to the account. To continue, please ensure your wireless network can emit a 2.4 Ghz signal to add devices. Your phone or tablet should be able to switch between 5Ghz or 2.4Ghz.
   • NOTE: This is only required for the device installation. Ordinary management of the device occurs through your preferred Wi-Fi network.
3. In the app, click the Add Device icon (+) to add a device to find.
4. Select Small Home Appliance from the categories on the left. Scroll down and choose Thermostat (Wi-Fi) from the choices.
5. The app should show the name of your 2.4 Ghz networks) or phone hotspot. Enter the password for such a network and click Next.
6. On the device, hold the Mode and the Up arrow simultaneously until the Wi-Fi icon begins to blink.
7. On the app, confirm that the Wi-Fi indicator is blinking. If so, choose Blink Quickly.
8. After 2 minutes or less, the app should find the device.
9. The app will now show the new device and a suggested name, which you can change on the next screen. Select Done. To the right of the name, a pencil icon allows you to change the name. The name should reflect the location of the device. This name will also be used when giving voice commands to Alexa or Google Assistant.
10. After successfully adding the device, your list of manageable devices should display. You can now open the new device to begin managing settings from anywhere, such as raising the temperature, using the digital dial, changing to manual settings or program settings, and enabling the child lock. etc.

ADDING THE ALEXA DEVICE

ADDING A THERMOSTAT TO THE ALEXA DEVICE

1. Open the Alexa app on your smartphone or tablet.
2. From the “hamburger” menu, select Skills & Games. On the top right, select the magnifying glass to search and enter the name of the application you installed on Page 5, Tuya or Smart Life.
3. Once found, select it to link to your Alexa account.
4. Select Enable to Use if this is the first time using it. You’ll need to provide your Tuya or Smart Life username and password for Alexa to be able to manage the devices.
5. After entering the login information, select Authorize.
6. You should receive a message such as “Smart Life has been successfully linked”. Click on Done.
7. Click the option to Discover Devices. After a brief moment, the new device should show up. If no device is found, close the Alexa app and wait a few minutes, relaunch the Skills and Games options and reopen the Tuya or Smart Life applications.
8. Once found within Alexa, you may use voice commands to control your thermostat.
9. For a list of common commands or to view a step-by-step video of the installation steps, go to the Alexa Commands section of the KALOR TECH website at kalortech.ideasolver.com, where you may download these instructions and additional material.

References

• ideasolver.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>