Iton Technology BW3456-44B1 1T1R+BT5.2 Combo Module User Manual

Iton Technology BW3456-44B1 1T1R+BT5.2 Combo Module

Device Overview

Features

General Features

• Supports battery voltage range from 3.0V to 4.8V supplies with internal switching regulator
• 1 antennas to support 1T1R technology and Bluetooth
• WPA and WPA2 support for powerful encryption and authentication
• AES and TKIP in hardware for faster data encryption and IEEE 802.11i compatibility
• Reference WLAN subsystem provides Cisco Compatible Extensions(CCX,CCX 2.0 CCX 3.0 ,andCCX4.0 )
• Reference WLAN subsystem provides Wi-Fi Protected Setup (WPS)Support external crystal andinternal crystal
• Support standard SDIO v3.0(including DDR50 mode at 50Mhz and SDR104 mode at 208Mhz ,b-bit and1bit)interfaces.
• Backward compatible with SDIO v2.0 host interfaces.
• Interface support ,host controller interface(HCI) using a high speed UART interface and PCMfor audiodata .12.0mm*12.0mm LGA package

IEEE 802.11x Key Features

• IEEE 802.11ac compliant
• Single-stream spatial multiplexing up to 433.3 Mbps data rate .
• Programmable data rates from MCS0–MCS9 in 20, 40, and 80 MHz channels, as specifiedinIEEE802.11ac
• Full IEEE 802.11a/b/g/n legacy compatibility with enhanced performance
• TX and RX low-density parity check (LDPC) support for improved range and power efficiency
• Supports explicit IEEE 802.11ac transmit beamforming
• Supports Optional Short GI and Green Field modes in TX and RX
• Supports IEEE 802.15.2 external coexsitence interface to optimize bandwidth utilization with other co located wireless technologies such as LTE or GPS.

Bluetooth Key Features

• Complies with Bluetooth Core Specification Version 4.2 with provisions for supporting futurespecifications.Bluetooth Class 1 or Class 2 transmitter operation
• Supports multiple simultaneous Advanced Audio Distribution Profiles (A2DP) for stereo sound
• Low power comsumption improves battery life of handheld
• Adaptive frequency hopping(AFH) for reducing radio frequency interference
• Automatic frequency detection for standard crystal and TCXO values

Descriptions

The BW3456-44B1 module is a complete dual-band (2.4 GHz and 5 GHz) Wi-Fi 1 × 1 MAC/baseband/RadioSystem-on-a-Module. It provides the highest level of integration for IoT applications handheldwirelesssystems.In IEEE 802.11ac mode, the WLAN operation supports rates of MCS0–MCS9 (up to 256 QAM) in20MHz, 40MHz, and 80 MHz channels for data rates up to 433.3 Mbps. In addition, all the IEEE 802.11a/b/g/nrates are supported.

Functional Block Diagram

Pin Configuration and Functions

Module Pin Diagram

Pin Functions

used by the WLAN section. Also, when deasserted, this pin holds the WLAN section in reset. This pin has an internal 200k ohm pull down resistor that is enabled by default. It can be disabled through programming
13| WL_SDIO_HOSTWAKE| WL Host Wake
14| SDIO_DATA2| SDIO Data Line 2
15| SDIO_DATA3| SDIO Data Line 3
16| SDIO_CMD| SDIO Command Input
17| SDIO_CLK| SDIO Clock Input
18| SDIO_DATA0| SDIO Data Line 0
19| SDIO_DATA1| SDIO Data Line 1
20| GND| Ground
21| VIN_LDO_OUT| Internal Buck voltage generation pin
22| VDDIO| 1.8V-3.3V VDDIO supply for WLAN and BT
23| VIN_LDO| Internal Buck voltage generation pin
24| SUSCLK_IN| External 32K or RTC clock
25| BT_PCM_OUT| PCM data Out
26| BT_PCM_CLK| PCM Clock
27| BT_PCM_IN| PCM data Input
28| BT_PCM_SYNC| PCM Synchronization control
29| GPIO_7| SDIO mode selection pin 1.8V:pull up, connect to 1.8V 3.3V:pull down, connect to GND with using a 10K resistor or less
30| NC| No connected
31| GND| Ground
32| NC| No connected
33| GND| Ground
34| BT_REG_ON| Used by PMU to power up or power down the internal regulators used by the Bluetooth section. Also, when deasserted, this pin holds the Bluetooth section in reset. This pin has an internal 200k ohm pull down resistor that is enabled by default. It can be disabled through programming
35| NC| No connected
36| GND| Ground
37| GPIO_6| GPIO configuration pin
38| GPIO_3| GPIO configuration pin
39| GPIO_5| GPIO configuration pin
40| GPIO_2| GPIO configuration pin
41| BT_UART_RTS_N| High-Speed UART RTS
42| BT_UART_TXD| High-Speed UART Data Out
43| BT_UART_RXD| High-Speed UART Data In
44| BT_UART_CTS_N| High-Speed UART CTS

Specifications

General Characteristics

environment)
Data Security| WEP,WPA/WPA2
Transmit Power(Conducted)| 2.4G:

• 11b 11Mbps:17±2dBm 11b 11Mbps:17±2dBm 11g 6Mbps:16±2dBm 11g 54Mbps:15±2dBm
• 11n HT20 MCS0:17±2dBm
• 11n HT20 MCS7:14±2dBm

5G:

• 11a 6Mbps:17±2dBm 11a 54Mbps:15±2dBm
• 11n HT20 MCS0:17±2dBm
• 11n HT20 MCS7:14±2dBm
• 11n HT40 MCS0:17±2dBm
• 11n HT40 MCS7:14±2dBm
• 11ac VHT20 MCS0:17±2dBm
• 11ac VHT20 MCS8:12±2dBm
• 11ac VHT40 MCS0:17±2dBm
• 11ac VHT40 MCS9:11±2dBm

Rx Sensitivity| 11ac VTH80 MCS0:17±2dBm

11ac VTH80 MCS9:11±2dBm

---|---
2.4G:

• 11b 11M:-87dBm@8% PER
• 11g 54M: -76dBm@10% PER
• 11n HT20 MCS7: -74dBm@10% PER
• 11n HT40 MCS7: -71dBm@10% PER

5G:

• 11a 54M:-73dBm@10% PER
• 11n HT20 MCS7: -71dBm@10% PER
• 11n HT40 MCS7: -68dBm@10% PER
• 11ac VTH20 MCS8:-66dBm@10% PER
• 11ac VTH40 MCS9:-63dBm@10% PER
• 11ac VTH80 MCS9:-59dBm@10% PER

Data Rate|

• 802.11b [11,5.5,2 and 1Mbps]
• 802.11g [54,48,36,24,18,12,9&6Mbps]
• 802.11n HT20:up to 72.2Mbps
• 802.11n HT40:up to 150Mbps 802.11ac VHT80:up to 433.3Mbps

Frequency Error| 2.4GHz:<±25 ppm(11b),<±20 ppm(11g/n);5GHz:<±20 ppm
Ambient Temperature| -30℃~85℃
Storage Temperature| -40℃~125℃
Antenna| External PF antenna
Operating System| Linux
Operating Voltage| VBAT: 3.0 ~ 4.8V ; typical: 3.6V VIO : 1.8 ~ 3.3V

RF Characteristics

All measurements are made under nominal supply voltage & room temperature, and conducted conditionsat
antenna port rather than antenna.

Receiver RF Specifications

Parameter| Conditions| FER<8%, Packet size= 1,024bytes| Min.| Nom.| Max.| Unit
---|---|---|---|---|---|---
Receive Input Frequency|
2.4GHz| 802.11b/g/n mode| 2400| –| 2500| MHz
Receiver Sensitivity|
802.11b| 1Mbps| –| –| -82| dBm
2Mbps| –| –| -80| dBm
5.5Mbps| –| –| -78| dBm
11Mbps| –| –| -76| dBm
802.11g| 6Mbps| PER<10%, Packet size= 1,024bytes| –| –| -82| dBm
---|---|---|---|---|---|---
9Mbps| –| –| -81| dBm
12Mbps| –| –| -79| dBm
18Mbps| –| –| -77| dBm
24Mbps| –| –| -74| dBm
36Mbps| –| –| -70| dBm
48Mbps| –| –| -66| dBm
54Mbps| –| –| -65| dBm
802.11n (HT20)| MCS0.| PER<10%, Packet size= 4,096bytes| –| –| -80| dBm
MCS1.| –| –| -77| dBm
MCS2| –| –| -75| dBm
MCS3.| –| –| -72| dBm
MCS4.| –| –| -68| dBm
MCS5.| –| –| -64| dBm
MCS6.| –| –| -63| dBm
MCS7.| –| –| -62| dBm
802.11n (HT40)| MCS0.| PER<10%, Packet size= 4,096bytes| –| –| -77| dBm
MCS1.| –| –| -74| dBm
MCS2| –| –| -72| dBm
MCS3.| –| –| -69| dBm
MCS4.| –| –| -65| dBm
MCS5.| –| –| -61| dBm
MCS6.| –| –| -60| dBm
MCS7.| –| –| -59| dBm
Maximum Input Level| | | | | |
802.11b| FER<8%| | -10| –| –| dBm
802.11g| FER<10%| | -20| –| –| dBm
802.11n| FER<10%| | -30| | | dBm
Parameter| Conditions| FER<10%, Packet size= 1,024bytes| Min.| Nom.| Max.| Unit
---|---|---|---|---|---|---
Receive Input Frequency| |
5GHz| 802.11a/n/ac mode| 4900| –| 5845| MHz
Receiver Sensitivity| | | | |
802.11a| 6Mbps| –| –| -82| dBm
9Mbps| –| –| -81| dBm
12Mbps| –| –| -79| dBm
18Mbps| –| –| -77| dBm
24Mbps| –| –| -74| dBm
36Mbps| –| –| -70| dBm
802.11n (HT20)| 48Mbps| PER<10%, Packet size= 4,096bytes| –| –| -66| dBm
---|---|---|---|---|---|---
54Mbps| –| –| -65| dBm
6Mbps| –| –| -80| dBm
9Mbps| –| –| -77| dBm
12Mbps| –| –| -75| dBm
18Mbps| –| –| -72| dBm
24Mbps| –| –| -68| dBm
36Mbps| –| –| -64| dBm
48Mbps| –| –| -63| dBm
54Mbps| –| –| -62| dBm
802.11n (HT40)| MCS0.| PER<10%, Packet size= 4,096bytes| –| –| -77| dBm
MCS1.| –| –| -74| dBm
MCS2| –| –| -72| dBm
MCS3.| –| –| -69| dBm
MCS4.| –| –| -65| dBm
MCS5.| –| –| -61| dBm
MCS6.| –| –| -60| dBm
MCS7.| –| –| -59| dBm
802.11ac (VHT80)| MCS0.| PER<10%, Packet size= 4,096bytes| –| –| -76| dBm
MCS1.| –| –| -73| dBm
MCS2| –| –| -71| dBm
MCS3.| –| –| -68| dBm
MCS4.| –| –| -64| dBm
MCS5.| –| –| -60| dBm
MCS6.| –| –| -59| dBm
MCS7.| –| –| -58| dBm
MCS8.| –| –| -53| dBm
MCS9.| –| –| -51| dBm
Maximum Input Level|
802.11a| FER<10%| -30| –| –| dBm
802.11n| FER<10%| -30| –| –| dBm
802.11ac| FER<10%| -30| –| –| dBm

Transmitter RF Specifications

802.11b/g/n
Transmit Power|
802.11b| 11Mbps| 15| 17| 19| dBm
802.11g| 54Mbps| 13| 15| 17| dBm
802.11n| HT20, MCS7| 12| 14| 16| dBm
HT40, MCS7| 12| 14| 16| dBm
802.11b| fc-22MHz<f<fc-11MHz&fc+11MHz<f< fc+22MHz| –| –| -30| dBr
fc-55MHz<f<fc-22MHz&fc+22MHz<f<

fc+55MHz

| –| –| -50| dBr
802.11g| fc±9MHz| –| –| 0| dBr
fc±11MHz| –| –| -20| dBr
fc±20MHz| –| –| -28| dBr
fc±30MHz| –| –| -40| dBr
802.11n| fc±9MHz| –| –| 0| dBr
fc±11MHz| –| –| -20| dBr
fc±20MHz| –| –| -28| dBr
fc±30MHz| –| –| -45| dBr
Center Frequency Tolerance|
802.11b| 1Mbps| -25| –| +25| pmm
802.11g/n| -20| –| +20| pmm
EVM(Error Vector Magnitude)*| | | |
802.11b| –| –| 35| %
2Mbps| –| –| 35| %
5.5Mbps| –| –| 35| %
11Mbps| –| –| 35| %
802.11g| 6Mbps| –| –| -5| %
9Mbps| –| –| -8| dB
12Mbps| –| –| -10| dB
18Mbps| –| –| -13| dB
24Mbps| –| –| -16| dB
36Mbps| –| –| -19| dB
48Mbps| –| –| -22| dB
54Mbps| –| –| -25| dB

EVM:
Method: composite EVM method.
Phase correction: Symbol-by-symbol correction.
Channel estimation: Raw channel estimate Raw Long Symbols.
Symbol timing correction: on.
Frequency Sync: Long training symbol.

802.11nMCS0.802.11acMCS0.

Remarks

EVM :
Method: composite EVM method.
Phase correction: Symbol-by-symbol correction.
Channel estimation: Raw channel estimate Raw Long Symbols. Symbol timing correction: on.
Frequency Sync: Long training symbol.

Bluetooth RF Specifications

Parameter| Conditions| Minimum| Typical| Maximum| Unit
---|---|---|---|---|---
Frequency range| GFSK| 2402| -88| 2480| MHz
RX sensitivity| –| –| dBm
π/4-DQPSK| –| -95| –| dBm
8-DPSK| –| -88| –| dBm
Output power (Conducted)| BDR| –| 8| –| dBm
EDR| –| 6| –| dBm
LE| –| 7| –| dBm

Application, Implementation, and Layout

Wi-Fi Application Diagram

Mechanical Size，Package and Layout Recommendation

Mechanical Size

Layout Recommendation

(Unit: mm)

Package Information

Thermal Reflow

Referred to IPC/JEDEC standard.
Peak temperature: <250°C
Number of times: ≤2

Note: The module is recommended not to go through reflow oven twice

Ordering Information

Part NO.| Working Voltage| ANT| Shielding Cover| 37.4M Crystal
---|---|---|---|---
BW3456-44B1| 3.0V~4.8V DC| External antenna| Included| Yes
BW3456-44B2| 3.0V~4.8V DC| External antenna| Included| No

Revision History

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur inaparticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and (2) this device must accept any interference received, including interferencethat may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority tooperatethe equipment

*RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shouldbeinstalled and operated with minimum distance 20cm between the radiator & your body. The OEM must certify the final end product to comply with unintentional radiators (FCC Sections 15.107 and 15.109) before declaring compliance of the final product to Part 15 of the FCC rules and regulations. Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change. The OEM must comply with the FCC labeling requirements. If the module’s label is not visible when installed, then an additional permanent label must be applied on the outside of the finished product which states: “Contains transmitter module FCC ID: VYVBW436S-44B1 ”.
Additionally, the following statement should be included on the label and in the final product’s user manual: “This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interferences, and
2. this device must accept any interference received, including interference that may cause undesired operation.” The moduleislimited to installation in applications. Separate approval is required for all other operating configurations, including portableconfiguration with respect to Part 2.1093 and different antenna configurations. A module or modules can only be used without additional authorizations if they have been tested and granted under the same intended end – use operational conditions, includingsimultaneous transmission operations. When they have not been tested and granted in this manner, additional testing and/or FCC application filing may be required. The most straightforward approach to address additional testing conditions is to have thegrantee responsible for the certification of at least one of the modules submit a permissive change application. When having amodule grantee file a permissive change is not practical or feasible, the following guidance provides some additional options for host manufacturers. Integrations using modules where additional testing and/or FCC application filing(s) may be required are: (A) amodule used in devices requiring additional RF exposure compliance information (e.g., MPE evaluation or SAR testing); (B) limitedand/or split modules not meeting all of the module requirements; and (C) simultaneous transmissions for independent collocatedtransmitters not previously granted together.
   This Module is full modular approval, it is limited to OEM installation ONLY.
   Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change. (OEM)
   Integrator has to assure compliance of the entire end product include the integrated Module.
   Additional measurements (15B) and/or equipment authorizations (e.g. Verification) may need to be addressed depending onco-location or simultaneous transmission issues if applicable. (OEM) Integrator is reminded to assure that these installationinstructions will not be made available to the end user

Integration instructions for host product manufacturers according to KDB 996369 D03 OEM

Manual v01

List of applicable FCC rules

FCC Part 15 Subpart C 15.247 &15.407& 15.207 & 15.209 & 15.205

Specific operational use conditions

802.11g: OFDM (BPSK, QPSK, 16QAM, 64QAM)

802.11n: OFDM (BPSK, QPSK, 16QAM, 64QAM)

Operation Mode| :| a n(HT20) n(HT40) ac(VHT20) ac(VHT40) ac(VHT80)
Device Type| :| Client
TPC Function| :| Without TPC
DFS Type| :| Slave without radar detection
Operation Frequency| :| Wi-Fi 5.2G: 5150~5250MHz Wi-Fi 5.3G: 5250~5350MHz

Wi-Fi 5.6G: 5470~5725MHz Wi-Fi 5.8G: 5725~5850MHz

**** Number of Channel| :| Wi-Fi 5.2G:

 4 Channels for 20MHz bandwidth (5180-5240MHz)  2 Channels for 40MHz bandwidth (5190-5230MHz)  1 Channels for 80MHz bandwidth (5210MHz)

Wi-Fi 5.3G:

 4 Channels for 20MHz bandwidth (5260-5320MHz) 2 Channels for 40MHz bandwidth (5270-5310MHz)  1 Channels for 80MHz bandwidth (5290MHz)

| | Wi-Fi 5.6G:

 11 Channels for 20MHz bandwidth (5500-5700MHz) 5 Channels for 40MHz bandwidth (5510-5670MHz) 2 Channels for 80MHz bandwidth (5530~5610MHz)

Wi-Fi 5.8G:

5 Channels for 20MHz bandwidth (5745MHz ~ 5825MHz)  2 Channels for 40MHz bandwidth (5755MHz ~ 5795MHz) 1 Channels for 80MHz bandwidth (5775MHz)

Modulation Type| :| 802.11a: OFDM (64QAM, 16QAM, QPSK, BPSK)

 802.11n: OFDM (BPSK, QPSK, 16QAM, 64QAM)

 802.11ac: OFDM (BPSK, QPSK, 16QAM, 64QAM, 256QAM)

Ant type| **| FPC Antenna
Ant Gain| **| Gain: 2.25dBi for 2.4G; Wi-Fi 5.2G: 2.03 dBi; Wi-Fi 5.3G: 1.83 dBi; Wi-Fi 5.6G: 1.96 dBi Wi-Fi 5.8G: 2.19 dBi Manufacturer: SHENZHEN HANYANG ANTENNA DESIGN CO.LTD.

The module can be used for mobile or portable applications with a maximum2.25 dBi antenna. The host manufacturer installing this module into their product must ensure that the final composit product complies with the FCC requirements by a technical assessment or evaluationto the FCC rules, including the transmitter operation. The host manufacturer has to be aware not to provide informationto the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.

Limited module procedures

Not applicable. The module is a Single module and complies with the requirement of FCCPart 15.212.

Trace antenna designs

You can see antenna size is 36.2mm14.6mm From below Specification.

Please refer to the chart below for PCB size of RF line terminal.

Scrape a GND off the side of the J1,connect the FPC antenna to the PCB at the position of theJ1 connector.
[The line between the FPC antenna and the WiFi module] must be 50 ohm. C1 is 10pF Capacitors.

RF exposure considerations

The device can be used in portable exposure condition without restriction and if RF exposure statement or module layout is changed, then the host product manufacturer required to take responsibility of the module through a change in FCC ID or newapplication. The FCC IDof themodule cannot be used on the final product. In these circumstances, the host manufacturer will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Antennas
This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.The module requires professional installation, and the antenna type cannot be changed. The gain cannot exceed 2.25dBi.

This device is intended only for host manufacturers under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna; The module shall be only used with the External antenna(s) that has been originally tested andcertified with this module. The antenna must be either permanently attached or employ a ‘unique’antenna coupler. As long as the conditions above are met, further transmitter test will not be required. However, the host manufacturer is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheralrequirements, etc.)

Label and compliance information

Host product manufacturers need to provide a physical or e-label stating

“Contains FCC ID: VYVBW3456-44B1 With their finished product.

Information on test modes and additional testing requirements

2Mbps

Operation Frequency| :| 2402~2480MHz
Number of Channel| :| 40 Channels
Operation Mode| :| 802.11b|  802.11g| 802.11n(HT20)| 802.11n(HT40)
Operation Frequency| :| 2412~2462MHz
Number of Channel| :| 11 Channel for 20MHz bandwidth (2412~2462MHz)
Modulation Type| :|  802.11b: DSSS (CCK, DQPSK, DBPSK)

 802.11g: OFDM (BPSK, QPSK, 16QAM, 64QAM)

 802.11n: OFDM (BPSK, QPSK, 16QAM, 64QAM)

Operation Mode| :|    a|  n(HT20)| n(HT40)|  ac(VHT20)
| | ac(VHT40) ac(VHT80)
---|---|---
Device Type| :| Client
TPC Function| :|  Without TPC
DFS Type| :|  Slave without radar detection
Operation Frequency| :| Wi-Fi 5.2G: 5150~5250MHz Wi-Fi 5.3G: 5250~5350MHz

Wi-Fi 5.6G: 5470~5725MHz Wi-Fi 5.8G: 5725~5850MHz

Number of Channel| :| Wi-Fi 5.2G:

 4 Channels for 20MHz bandwidth (5180-5240MHz) 2 Channels for 40MHz bandwidth (5190-5230MHz) 1 Channels for 80MHz bandwidth (5210MHz)

Wi-Fi 5.3G:

4 Channels for 20MHz bandwidth (5260-5320MHz) 2 Channels for 40MHz bandwidth (5270-5310MHz) 1 Channels for 80MHz bandwidth (5290MHz)

Wi-Fi 5.6G:

11 Channels for 20MHz bandwidth (5500-5700MHz) 5 Channels for 40MHz bandwidth (5510-5670MHz) 2 Channels for 80MHz bandwidth (5530~5610MHz) Wi-Fi 5.8G:

5 Channels for 20MHz bandwidth (5745MHz ~ 5825MHz) 2 Channels for 40MHz bandwidth (5755MHz ~ 5795MHz)

1 Channels for 80MHz bandwidth (5775MHz)

Modulation Type| :| 802.11a: OFDM (64QAM, 16QAM, QPSK, BPSK)

802.11n: OFDM (BPSK, QPSK, 16QAM, 64QAM)

802.11ac: OFDM (BPSK, QPSK, 16QAM, 64QAM, 256QAM)

Ant type| | FPC Antenna
Ant Gain| | Gain: 2.25dBi for 2.4G; Wi-Fi 5.2G: 2.03 dBi; Wi-Fi 5.3G: 1.83 dBi; Wi-Fi 5.6G: 1.96 dBi Wi-Fi 5.8G: 2.19 dBi Manufacturer: SHENZHEN HANYANG ANTENNA DESIGN CO.LTD.

Host manufacturer must perfom test of radiated & conducted emission and spurious emission, etcaccording to the actual test modes for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. Only when all the test results of test modes comply with FCC requirements, then the end
product canbe sold legally.

Additional testing, Part 15 Subpart B disclaimer

The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.247 &15.407& 15.207 & 15.209 & 15.205and that the host product manufacturer is responsible for complianceto any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

The user manual of the end product should include:

• a) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
• b) The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.
• c) This device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• d) This device is restricted to indoor use.
• e) The antenna( s ) used for this transmitter must not transmit simultaneously with any other antenna or transmitter.

DISCLAIMER AND COPYRIGHT NOTICE
Information in this document, including URL references, is subject to change without notice.
This document is provided “As if” with no whatsoever, including any warranty of merchantability, noninfringement, fitness for any purpose, or any warranty otherwise arising out of any proposal, specification or samples.
All liability, including liability for infringement of any proprietary rights, relating to use of information in this document is disclaimed. No licenses express or implied, by estoppel or otherwise, to any intellectual property rights are granted herein.
The Bluetooth logo and symbol belong to the Bluetooth SIG Inc.
The Wi-Fi Alliance Member Logo is a trademark of the Wi-Fi Alliance.
All trade names, trademarks and registered trademarks mentioned in this document are property of their respective owners, and are hereby acknowledged.
Copyright ITON Technology Corp. All rights reserved.

References

• ITON Technology Corp.-Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>