Figure 8. TZ8258-27A1 Module Size
4.3 Recommended Land Pattern

Figure 9. TZ8258-27A1 Module Recommended land Pattern

ITON Technology Corp.

Page 8 of 16

www.sziton.com
5. Application Notice
5.1 SMT Temperature Setting Recommendation
Referred to JEDEC/IPC J-STD-020 standard. Peak temperature:<260 Number of times: 2

TZ8258-27A1
V0.1-Jan., 2024

Figure 10. TZ8258-27A1 module SMT temperature settings recommendation

ITON Technology Corp.

Page 9 of 16

www.sziton.com
6. Packaging

TZ8258-27A1
V0.1-Jan., 2024

The TZ8258-27A1 module is shipped in tape and reel, and the minimum package is 600 PCS.

Figure 11. TZ8258-27A1 module packaging
7. Ordering Information

Part NO. TZ8258-27A1

Working Voltage 3.3V

ANT Metal antenna

Size 17.0mm14.0mm4.4mm

Mark

8. Revision History

Version V0.1 Draft Version

Change Content

Date 2024.1.30

Reviser Phil

ITON Technology Corp.

Page 10 of 16

www.sziton.com

TZ8258-27A1
V0.1-Jan., 2024

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment

*RF warning for Mobile device:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 20cm between the radiator & your body.

The OEM must certify the final end product to comply with unintentional radiators (FCC Sections 15.107 and 15.109) before

declaring compliance of the final product to Part 15 of the FCC rules and regulations. Integration into devices that are directly or

indirectly connected to AC lines must add with Class II Permissive Change.

The OEM must comply with the FCC labeling requirements. If the module’s label is not visible when installed, then an

additional permanent label must be applied on the outside of the finished product which states: “Contains transmitter

module FCC ID: 2BF4V-TZ8258-27A1”.

Additionally, the following statement should be included on the label and in the final product’s user manual:

“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interferences, and

(2) this device must accept any interference received, including interference that may cause undesired operation.” The module is

limited to installation in applications. Separate approval is required for all other operating configurations, including portable

configuration with respect to Part 2.1093 and different antenna configurations. A module or modules can only be used without

additional authorizations if they have been tested and granted under the same intended end – use operational conditions, including

simultaneous transmission operations. When they have not been tested and granted in this manner, additional testing and/or FCC

ITON Technology Corp.

Page 4 of 11

www.sziton.com

TZ8258-27A1
V0.1-Jan., 2024

application filing may be required. The most straightforward approach to address additional testing conditions is to have the grantee responsible for the certification of at least one of the modules submit a permissive change application. When having a module grantee file a permissive change is not practical or feasible, the following guidance provides some additional options for host manufacturers. Integrations using modules where additional testing and/or FCC application filing(s) may be required are: (A) a module used in devices requiring additional RF exposure compliance information (e.g., MPE evaluation or SAR testing); (B) limited and/or split modules not meeting all of the module requirements; and (C) simultaneous transmissions for independent collocated transmitters not previously granted together.This Module is full modular approval, it is limited to OEM installation ONLY. Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change. (OEM) Integrator has to assure compliance of the entire end product include the integrated Module. Additional measurements (15B) and/or equipment authorizations (e.g. Verification) may need to be addressed depending on co-location or simultaneous transmission issues if applicable. (OEM) Integrator is reminded to assure that these installation instructions will not be made available to the end user. Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01

2.2 List of applicable FCC rules FCC Part 15 Subpart C 15.247 & 15.207 & 15.209 & 15.205

2.3 Specific operational use conditions When installed in smart terminal products, the host manufacturer must negotiate with the module manufacturer on the final installation method in the system.The module can be used for mobile applications with a maximum 2.26 dBi antenna. The host manufacturer installing this module into their product must ensure that the final compost product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation. The host manufacturer has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

The module should be installed and operated with minimum distance 20cm between the radiator & your body. and if RF exposure statement or module layout is changed, then the host product manufacturer required to take responsibility of the module through a change in FCC ID or new application. The FCC ID of the module cannot be used on the final product. In these circumstances, the host manufacturer will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.When the host is a portable device, it is necessary to take a SAR test with your set mounting this module. Class II permissive change application is necessary using the SAR report. Please contact kevin ([email protected]). And an application for a Class II permissive change from a Mobile equipment to a Portable equipment is also required.

ITON Technology Corp.

Page 12 of 16

www.sziton.com

TZ8258-27A1
V0.1-Jan., 2024

Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the spaces between human body and antenna exceeded 20cm.

1. According to the following requirements of the power supply DC3.3V, power up, about 3 seconds to to complete the initial. 2. open application software (need to install the company’s specific application software development, application software interface can be customized according to customer’s product requirements).

2.4 Limited module procedures The module is a Single module.
Requirement per 15.212 and KDB 996369 D01
The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal.
The module must contain power supply regulation on the module.
The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per §§ 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b).
The module must demonstrate compliance in a stand-alone configuration.
ITON Technology Corp.

Explanation from Grantee (do not write yes/no, but explain why product complies/how it is achieved) Has RF shielding.
The modular have buffered modulation/data inputs.
The modular transmitter have its own power supply regulation.(DC 3.3V) Antenna restrictions are added in the manual.The antenna needs to be professionally installed.
The module was tested in a stand-alone configuration, please refer to the Setup
Page 13 of 16

www.sziton.com

TZ8258-27A1
V0.1-Jan., 2024
Photo for the detail

The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (see KDB Publication 784748).
The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee.
The module must comply with RF exposure requirements

Please refer to label sample exhibit – host labeling is described in integration manual The required FCC rule has been fulfilled and all the instructions for the maintaining compliance have been clearly stated in the User Manual. The MPE evaluation with 20cm distance restriction is submitted for the compliance of RF Exposure requirement.

2.5 RF exposure considerations

The module complies with FCC radiation exposure limits set forth for an uncontrolled

environment.The module should be installed and operated with minimum distance 20cm

between the radiator & your body.

2.6 Antennas

This module has been approved to operate with the antenna types listed below, with the

maximum permissible gain indicated.The module antenna requires professional installation,

and the antenna type cannot be changed. The gain cannot exceed 2.26dBi.

Frequency band

Antenna Type

Model Number

Max Gain

2405-2480MHz

Shrapnel Antenna

TZ8258-27A1

2.26(dBi)

ITON Technology Corp.

Page 14 of 16

www.sziton.com

TZ8258-27A1
V0.1-Jan., 2024

This device is intended only for host manufacturers under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna; The module shall be only used with the External antenna(s) that has been originally tested and certified with this module. The antenna must be either permanently attached or employ a `unique’antenna coupler.

As long as the conditions above are met, further transmitter test will not be required. However, the host manufacturer is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheralrequirements, etc.). 2.7 Label and compliance information Host product manufacturers need to provide a physical or e-label stating
“Contains FCC ID: 2BF4V-TZ8258-27A1 With their finished product.

2.8 Information on test modes and additional testing requirements The module complies with FCC radiation exposure limits set forth for an uncontrolled
environment.The module should be installed and operated with minimum distance 20cm between the radiator & your body. and if RF exposure statement or module layout is changed, then the host product manufacturer required to take responsibility of the module through a change in FCC ID or new application. The FCC ID of the module cannot be used on the final product. In these circumstances, the host manufacturer will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.When the host is a portable device, it is necessary to take a SAR test with your set mounting this module. Class II permissive change application is necessary using the SAR report. Please contact kevin ([email protected]). And an application for a Class II permissive change from a Mobile equipment to a Portable equipment is also required.
Note) Portable equipment : Equipment for which the spaces between human body and antenna are used within 20cm. Mobile equipment : Equipment used at position in which the

ITON Technology Corp.

Page 15 of 16

www.sziton.com

TZ8258-27A1
V0.1-Jan., 2024

spaces between human body and antenna exceeded 20cm. Host manufacturer must perform test of radiated & conducted emission and spurious emission, etcaccording to the actual test modes for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. Only when all the test results of test modes comply with FCC requirements, then the end product canbe sold legally. 2.9 Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.247 & 15.207 & 15.209 & 15.205and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional- radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. 2.11 The user manual of the end product should include: a) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. b) The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. c) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. d) This device is restricted to indoor use. e) The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter.

ITON Technology Corp.

Page 16 of 16

References

• ITON Technology Corp.-Home

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>