amazon basics B07ST25WDG 20-150 1 4 Inch Drive Click Torque Wrench User Manual

amazon basics B07ST25WDG 20-150 1 4 Inch Drive Click Torque Wrench

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.

When using the product, basic safety precautions should always be followed to reduce the risk of injury including the following:

• Do not use the product to loosen bolts, screws or the like, as this might damage the ratchet and the calibrated settings.
• Do not use brute force on the product to tighten a nut/ screw. During tightening apply a steady and consistent pressure. Do not use as a nut breaker, pry bar, hammer, or lever bar.
• To prevent damage to the product, stop applying pressure when the “click” sound is heard. Bear in mind that the “click” sound is acoustically weaker with lower torque settings.
• The product should be re-calibrated when it has been subjected to an overload greater than its rated capacity, after repair, or after any improper handling which might influence the errors of measurement.
• Do not use worn or damaged accessories (sockets or extension pieces), as these may negatively influence the accuracy of the applied force.
• Use only within rated torque range.
• Do not use a product that has been dropped. Have it tested before putting back into use.

Product Description

• A Square drive
• B Direction switch for ratchet function
• C Spanner shaft
• D Lock ring
• E Handle
• F Coarse adjustment scale (Lb.in / N m)
• G Fine adjustment scale
• H Storage box

Intended Use

• This product is intended to apply a specific torque force to a fastener such as a nut or bolt.
• This product is intended for household use only. It is not intended for commercial use.
• No liability will be accepted for damages resulting from improper use or non-compliance with these instructions.

Before First Use

Danger Risk of suffocation!
Keep any packaging materials away from children – these materials are a potential source of danger, e.g. suffocation.

• Check the product for transport damages.
• Remove all the packing materials.

Operation

Setting the torque

This product is a dual-range torque wrench marked with pound inch (Lb.in) and Newton meters (N m) on opposite sides of spanner shaft (C).

NOTICE The desired torque force is summed up by finding the largest possible value in the coarse scale (F) that is within the desired torque force to be applied.

• Use the fine adjustment scale (G) to reach the desired value accurately.
• Pull the lock ring (D) downwards to unlock and hold  down while setting the torque value.
• Turn the handle (E) clockwise to increase the torque and in anti-clockwise direction to decrease the torque. The coarse and fine scale (F, G) show the torque value.
• The precise value is set by additional turning of the handle. The number on the fine adjustments scale at the vertical line is the added torque to the value of the selected torque margin.
• Push the lock ring (D) upwards to lock.
• For precise scale adjustment, use in-lb scale. The conversion formula between in.lb scale and Nm scale are: 1 Nm=B.86 in-lb, 1 in.lb=0.1129 Nm.
  Example: Setting the torque to 10.8 N m

For regular integer Nm scale setting reference images, refer to p.85, 86.
Example: Setting the torque to 108 lb. in

Tightening

• Fit an extension (not included) if required to the head (A).
• Set ratchet function direction on the direction changer (B).
• Install properly sized socket/attachment to the square drive (A).
• Set the direction switch (B) to tighten position.
• Operate the torque wrench the same as a standard socket wrench to tighten the bolt/nut.
• Place the socket on bolt/nut and tighten slowly and steadily until the “click” sound is heard. Stop pulling the wrench and release the pressure on the handle (E). The bolt/nut is now tightened to the required torque setting.
• Do not continue to pull after the torque setting is reached. Doing so will over-tighten the bolt/nut and could damage the wrench.

Maintenance

The product is lubricated for life and should not be oiled. The only exception is the ratchet mechanism which may be lubricated as needed for smooth operation.

NOTICE This product is a precision measuring instrument. Calibration must be done regularly to ensure accuracy. It is recommend to re-calibrate the product no later than 10,000 cycles or 12 months after the date it is put in service, whichever comes first.

Storage

• It This product is a precision instrument and should be stored with care using provided storage box. Avoid any vibrations and shocks.
• Set the torque to the lowest level before storage.

Specifications

• Maximum torque value: 20 – 150 lb.in (25 15 N m)
• Accuracy :  +/-3%
• Net weight: approx. 13.7 oz (390 g)
• Dimensions (Wx H x D):   approx. 10 x 1.3 x 1.3″ (25.4 x 3.4 x 3.4 cm)

Importer Information

For EU

• Postal:   Amazon EU S.a r.1., 38 avenue John F. Kennedy, L-1855 Luxembourg
• Business Reg.: 134248

For UK

• Postal : Amazon EU SARL, UK Branch, 1 Principal Place, Worship St, London ECZA 2FA, United Kingdom
• Business Reg.: BR017427

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review. Scan QR Code below with your phone camera or QR reader:

US:

• UK: amazon.co.uk/review/review-your-purchases# If you need help with your Amazon Basics product, please use the website or number below.
• US: amazon.com/gp/help/customer/contact-us
• UK: amazon.co.uk/gp/help/customer/contact-us
• +1 877-485-0385 (US Phone Number)

amazon.com/AmazonBasics
MADE IN CHINA FABRIQUÉ EN CHINE HERGESTELLT IN CHINA PRODOTTO IN CINA HECHO EN CHINA GEMAAKT IN CHINA  WYPRODUKOWANO W CHINACH TILLVERKAD I KINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>