SCARLETT comfort SC-SF111RC12 Stand Fan Instruction Manual
- June 4, 2024
- SCARLETT comfort
Table of Contents
SCARLETT comfort SC-SF111RC12 Stand Fan
DESCRIPTION
- Front grille
- Front grille clips
- Blade cap
- Blades
- Rear grille nut
- Rear grille
- Motor
- Motor shaft
- Control box
- Screw A
- Vertical adjustment screw
- Stand cover
- Extension pole
- Out-joint
- Stand tube
- Stand base
- Switch mode buttons
- Remote controller
- Oscillating knob
DIMENSION
INSTRUCTION MANUAL IMPORTANT SAFEGUARDS
Important safeguards. read carefully and keep for future reference.
Incorrect operation and improper handling can lead to malfunction of the
appliance and injuries to the user. Before connecting the appliance for the
first time check that voltage indicated on the rating label corresponds to the
mains voltage in your home.
- For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual.
- Do not use outdoors.
- The appliance is not intended for use for physically, sensory or mental disabled person (including children) or for person with lack of life experience or knowledge, if only they are under supervision or have been instructed about the use of the unit by responsible person.
- Children must be under control in order not to be allowed to play with the appliance.
- Always unplug the appliance from the power supply before cleaning and when not in use.
- To prevent risk of electric shock and fire, do not immerse the appliance in water or any other liquids. If it has happened DO NOT TOUCH the appliance, unplug it immediately and check in a service center.
- Do not use the device in bathrooms and near water.
- Do not place the appliance near heat sources.
- Do not leave the appliance switched on when not in use.
- Do not use other attachments than those supplied.
- In case of power cord is damaged, its replacement should be done by the manufacture or service department or the other high-skill person to avoid any danger.
- Keep the cord away from sharp edges and hot surfaces.
- Do not pull, twist, or wrap the power cord around the appliance.
- Avoid contact with moving parts of the device. Do not put pencils or other objects through the protective grid of the fan.
- Do not operate without fan installed protective grid.
- Do not attempt to repair, adjust or replace parts in the appliance. Repair the malfunctioning appliance in the nearest service center.
- If the product has been exposed to temperatures below 0ºC for some time it should be kept at room temperature for at least 2 hours before turning it on.
- The manufacturer reserves the right to introduce minor changes into the product design without prior notice, unless such changes influence significantly the product safety, performance, and functions.
- Manufacturing date is indicated on the unit and/or on packing as well as in accompanying documents in the following format XX.XXXX where first two figures XX is the month of production, and following four figures XXXX is the year of production.
ASSEMBLING INSTRUCTIONS
- The device is intended for air circulation in the room.
- Fan is packed disassembled. Before assembling make sure that all the required parts are undamaged and included into the set.
- Do not plug in the device before its assembling is finished.
- Tighten stand tube to stand base.
- Unscrew out-joint, put the stand cover and base cover on the stand base, pull the extension pole out then tighten the out-joint again.
- Place control box firmly on top of extension pole, tighten screw B.
- Unscrew the blade cap by turning clockwise and rear grill nut by turning counter clockwise and put both blade cap and rear grill nut off the motor shaft.
- Put rear grille on motor shaft.
- Secure it with rear grille nut.
- Slide blades on motor shaft so that claws on motor shaft match the blades slots.
- Screw blade cap on shaft by turning counter clockwise.
- Put front grille on rear grille and close clips or screw grille ring to secure grilles together.
- Adjust the fan vertically by vertical adjustment screw.
- The fan is ready for work.
OPERATION MANUAL
CAUTION : To avoid electroconvulsive shock or fire danger, do not operate fan under the conditions of increased humidity.
Place fan only onto dry flat unyielding surface.
BUTTONS:
- ON/OFF button switches on the power/ button switches the fan off.
- Speed button switches the fan on and shifts between different speeds
- Mode button helps to choose operating mode of fan. Nor (normal) – air stream at constant rate
- Nat (nature) – air stream by intense waves
- Slp (sleep) – air stream by weak waves
- Timer button helps to adjust fan operating time up to maximum time of 7 hours and a half. Each pressing of this button adds half an hour of fan operating time. For example, if you wish to set operating time of 5 hours and a half, you need to do the following: Press the button “Timer” several times and see on display: 0.5h, 1h, 4h, that means you have set 5.5h
LIGHT INDICATORS:
- 0.5h…4h – fan operating time set
- Nor – air stream at constant rate
- Nat – air stream by intense waves
- Slp – air stream by weak waves
- H – high speed;
- M – middle speed;
- L – minimum speed;
REMOTE CONTROLLER:
- Mode settings can be made manually by using switch mode buttons on control box or by using remote controller:
- ON/OFF button switches on the power/ button switches the fan off.
- Speed button switches the fan on and shifts between different speeds.
- Mode button helps to choose operating mode of fan.
- Nor (normal) – air stream at constant rate
- Nat (nature) – air stream by intense waves
- Slp (sleep) – air stream by weak waves
- Timer button helps to adjust fan operating time. Each pressing of this button adds half an hour of fan operating time.
NOTE : Remote controller operates on AAА 1.5V batteries which are not included.
On the upper part of the motor cover there is oscillating knob. If pressed, it makes the fan cabinet with blades traverse from side to side. To cancel oscillating mode push oscillating knob upward.
MAINTENANCE
- Before cleaning unplug fan first.
- Do not use abrasive cleansers
- Clean front and rear grilles, blades, stand tube and stand base with soft moistened cloth and wipe dry.
STORAGE
- Keep the device in normal conditions in dry place.
- The symbol on the unit, packing materials and/or documentations means used electrical and electronic units should not be toss in the garbage with ordinary household garbage. These units should be pass to special receiving point.
- For additional information about actual system of the garbage collection address to the local authority.
- Valid utilization will help to save valuable resources and avoid negative work on the public health and environment which happens with incorrect using garbage.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>