AXKID 925 Car Seat Review Reviews Instruction Manual

AXKID 925 Car Seat Review Reviews Instruction Manual

Read this instruction manual before installing the car seat in your vehicle.
For more information and installation videos visit www.axkid.com.

Ax kid **MOVE KID**  is a rear-facing car seat approved for children with a height between 61-125 cm, ≤36 kg

Ax kid MOVE KID is suitable for use from approximately six months of age, or from when your child can sit up
unsupported.

This is an integral Specific vehicle Belted Enhanced Child Restraint System. It is approved according to UN Regulation No.

129, for use in compatible vehicle seating positions as indicated by the vehicle list. If in doubt, consult either the Enhanced Child Restraint System manufacturer (www.axkid.com) or the retailer.

Important information

To maximize your child’s safety, it is important that you keep the following in mind:

• Always follow the instructions in this manual. An incorrect installation may seriously affect the safety for your child. If in doubt, contact your retailer who can demonstrate a correct installation.
• Keep this instruction manual for future reference. If manual is lost, you can find it online at www.axkid.com
• Do not use the car seat in a seating position where an active frontal airbag is fitted. If you still wish to install the car seat in this location the airbag must be switched off according to the vehicle manufacturers instructions.
• Should you have an accident, no matter how small, your car seat should always be replaced. It may have damage that is not visible and could seriously affect the safety of your child. For this reason, Axkid does not recommend purchasing secondhand car seats.
• If the car seat has been exposed to direct sunlight, make sure the car seat is not too hot before installing your child.
• Never leave your child unattended in the vehicle.
• Ensure that any luggage or loose objects are secured in your vehicle as they may cause injuries to passengers in the event of an accident.
• Ensure that the car seat is installed in a way where no parts become trapped by movable seats, car doors, etc.
• If you are using lower tether anchorage straps, make sure they are installed in a way where they don’t interfere with the movement of any vehicle seat.
• The car seat may only be installed rear-facing.
• Always make sure that the harness is adjusted to correctly fit your child’s body. The harness is adjusted by moving the head support.
• Make sure that the child’s back is pushed against the car seat when restraining your child with the harness.
• Always make sure that the harness is firmly tightened against your child and that the buckle is completely locked, you should not be able to pinch the straps.
• Make sure there is no twist in the harness.
• Always make sure the support leg is in its correct position and that is has contact with the vehicle floor. The support leg is a very important safety feature designed to maximise your child’s safety in an accident.
• Do not attempt to disassemble or modify any part of the the car seat. The warranty and the safety performance of the car seat could be affected if doing so.
• Never use the car seat without the textile cover. The seat textile cover is a safety feature and may only be replaced with an Axkid original seat textile cover.
• Read the vehicle handbook and the vehicle list at www.axkid.com to find which seating positions are suitable for this car seat.
• Axkid recommends to always use a seat protection to protect your vehicle seat from scratches and dirt.
• If you have any doubts, contact the retailer where the car seat was purchased or contact info@axkid.com

Parts

• A HEADREST
• B INTEGRAL HARNESS
• C BUCKLE RELEASE BUTTON
• D SEAT BELT SLOT
• E HARNESS RELEASE BUTTON
• F HARNESS TENSION STRAP
• G HEADREST BRAKE LEVER
• H ASIP PAD
• I HEEL
• J VERTICAL LINE
• K METAL CLIP CONNECTOR
• L METAL CLIP
• M ASIP CONNECTOR
• N LOWER TETHER
• O BELT CLAMP
• P BELT CLAMP LID
• Q SUPPORT LEG
• R SUPPORT LEG BUTTON
• S SHOULDER STRAP
• T RECLINE ANGLE ADJUSTER

Allowed and disallowed positioning of Axkid MOVEKID car seat

Ax kid MOVE KID car seat can only be installed rear-facing. It will fit in most, but not all seating positions. Check your vehicle instruction manual to find suitable seating positions and check the vehicle list on www.axkid.com

Front passenger seat (no active airbag) : YES/NO*
Front passenger seat (active airbag) : NO
Rear passenger seat with 3-point seat belt: YES
Seat with 2-point seat belt : NO
Side and rear facing seats : NO

IMPORTANT: If you wish to install your Ax kid MOVE KID car seat in a location where a frontal airbag is fitted, the airbag must be disconnected according to your vehicle manufacturer instruction. Note that some vehicles require an authorized service center to disconnect the airbag.

• The General Regulation of Traffic in Spain, in its article 117, establishes the prohibition of driving with children of stature equal to or less than 135 centimeters located in the front seats of the vehicle, without exceptions.

Lower Tether Anchorages

Important info

Lower Tether Anchorages (LTA) are used to enhance the protection of children in cars by providing a firmand stable installation for extended rear-facing belt attached car seats. This increases the safety for your child in all types of collisions, including roll-over accidents and rear-end impacts.

Lower tethers are a well-established method that has been extensively used in the Nordic countries for over 40 years. In 2020 a new international standard for LTA, ISO13216-4:2020, was released. This standard describes the requirements for lower tethers for car seats but also for vehicle manufactures and their anchor points. The purpose is to improve the compatibility and ensuring a safe and easy way of installation for the future.

Axkid MOVEKID indcludes two lower tethers for installation in cars with or without lower tether anchorages.

The included lower tethers complies with ISO13216-4:2020 to ensure a perfect fit, and easy installation, in vehicles with pre-installed lower tether anchorages that also complies to this standard. If your vehicle has anchorage points that do not comply with the standard, Axkid MOVEKID lower tethers are still likely, but not guaranteed, to fit.

Pre-installed lower tether anchorages in vehicles are often found on the seat rails attached to the floor, but other positions are also used.

Check your vehicle’s instruction manual for more information on usable anchor points.

Ax kid MOVE KID comes with everything you need to install the car seat in your vehicle. However, lower tether anchorages and extra lower tether anchorage straps can be purchased seperately and will make installation quicker and easier in multiple cars. Some vehicle manufactures also offers the possibility of retrofitting lower tether anchorages. Contact your vehicle manufacturer or dealer for more information. Axkid retrofit lower tether anchorages and extra lower tethers can be purchased separately.

Note: Never use Ax kid MOVE KID without the lower tethers. They are an important safety feature and must always be used when installing your car seat.

Installing lower tethers

Always use two anchorage points when installing Axkid MOVEKID and choose anchorage points that are separated as this gives a more stable installation. Depending on your vehicle and the seat position where you choose to install your car seat, there are various possible anchorage points to use. See below for alternatives.

Lower tether routing options

alt. a Install the tether around the seat rail in front of the car seat by threading the tether between the seat rail and vehicle floor or through an appropriate hole of the seat rail.
alt. b Install the tether around the hinge of the vehicle seat in front of the car seat by threading the tether in between the vehicle seat back and seat cushion.
alt. c Install the tether around the seat rail below the car seat by threading the tether between the seat rail and vehicle floor or through appropriate hole of the seat rail.
alt. d Install the lower tether to a suitable anchorage point in the back of the vehicle and route the tether underneath the vehicle seat to the front of the vehicle. Make sure that the lower tether comes out from the front of the seat and not out from the sides.
alt. e When installing the Axkid MOVEKID in the front passenger seat, the tether should be wrapped around the nearest suitable anchor point that will allow the straps to be tightened fully. Anchor points set further back can be used, and if needed, the tether can be crossed over and even looped together with another tether.

LTA When installing the Axkid MOVEKID using lower tether anchorages (LTA), the lower tether (N) can be looped around the metal clip connector (K), and the metal clip (L) should be connected to the lower tether anchor.

Installing Axkid MOVEKID car seat in the vehicle

Before installing AXKID MOVEKID, make sure you have installed the lower tethers or lower tether anchorages in your vehicle. See section about Lower Tether Anchorages and Installing lower tethers in this manual for more information and installation instructions.

1. Unap the zipper and open the belt clamp lid (P)  Place the Avid MOVEND on the vehicle seat with the hack of the car seat faoing the front of the vehide. Adjust the legroom for your child by simply moving the car seat back and forth on the vehicle amat Axiod MOVEKID canbe ratalled tight agairet the vehicle sesat hack but may never be installed with the heel li hanging over the edge of the vehicle seat. Make sure that the vertical line (on the heel (1) never crosses the edge of the vehicle seat
   

2. Acdjust the angle of the car seat by choosing a suitable recline position with the moline angle adjuster (T) Formaximum safety, choose a position as upright as possible while also ensuing that your chidis head does not fall forward when sleeping For both comfort and safety reasons, the recline angle should be adjusted to a more upright position as your chid grows. Note that when tensioning the lower lethers (N), the car seed will be slightly more reclinedasit sinis into the vehicle sesat cushion Wheninstalling Aakiet MOVEKID in a front passenger seat it is possibile, haut not necessary for the back of the car sent to have contact with the dashboari.
   

3. Open the belt clamp (O. Pullout an arm length of the vehicle seat belt and thesadit through the seat belt slot closest to you Route the belt through the belt clamp (0) and thmad it through the seat belt slot (D) on the opposite side. Con nect the vehicle seat belt with the seat belt bucide and pull thund on the shoulder part of the vehicle past belt to remove all slack and to feesten the car seat, the harder youpul the firmer the installation. To give an even more firmand stable stallation pres.down on the car seat while pulling the vehicle beit. Whert the car seat is firmity fastened, cione the bed clamp (0) and lock the vehicle seat belt position. Make sure that boten the shoulder and lap bielt is locked together in the belt clamp (0) Close the belt clamplid (Pandolose the appe.
   

4. Attach the metal rips) to themetal clip connectors (K) on nach side of the child seat for connect the metal cips ) the anchorages in your vehicle if lower tether anchorages is used for installation See section Installing lower tethers in this manual for more information Press down on the top of the car seat while tensioning the lower tethers (N. By tensioning the lower tethers (N) you also set the final recline angle of the car seat. Keep pushing down and tensioning the car seat until it is firmly fastened, and you have achieved a suitable recline angle.
   

5. Pullout the support leg (Q) from the car seat. Push the support leg button (R) and pull the supporting (Q) downwards untit it is in contact with the vehicle floor Let go of the supporting button (R) and left the car seat upwards to further ex lend the support leg (Q) until you hear a click. The support leg (Q) should now be locked and firmly pressed against the vehicle floor. Make sure that the supporting (Q) is angled about 10 towards the front of the vehicle. Check the vehicle seat belt again to make sure that it is still firmly tensioned and that no slack has occurred in the hipbelt while terasoning the lower lethers and support leg if the vehicle telt has lost some lension simply re-tension it by repeating step 2 of this guide without disconnecting the lower tethers.
   

6. Push the ASIP pad into the picts on the ASP connectar (M) and slide downwards, the ASP pad wit dickinto place if thermis a plastic cover on the ASP connector (M), remove it and place on the ASIP connector (M) on the opposite side of the sout before fitting the ASP pad (H). Make sure the ASP pad (0-0 attached or the side of the Aviod MOVERIO thali closest to the vehicle door.
   

Restraining your child in Axkid MOVEKID car seat

Before restraining your child in the Axkid MOVEKID car seat, make sure you have the correct inlay installed in the seat. Axkid MOVEKID is designed to grow with your child and to ensure a comfortable and safe fit for the children. Axkid recommends using the inlay until it is too tight for your child, but to a minimum length according to table below (note that the age is just an indication):
Age: Height
Toddler 0-3 years: 61– 105 cm

Child 3-7 years: 106 – 125 cm

The Axkid MOVEKID is equipped with an adjustable headrest (A). See section Headrest adjustment for more information.

7. Adjust the headrest (A) to an approximate position for your child.
   

8. Loosen the harness by pressing the harness release button (E) and pull out both shoulder straps (S) at the same time. Avoid pulling only one strap at the time since it may cause the shoulder straps (S) to become uneven.
   

9. Unlock the harness buckle by pressing the buckle release button (C) and place the straps outside of the seat.
   

10. Place your child in the seat and place the shoulder straps (S) over your child’s shoulders. Pull and hold the headrest brake lever (G) to unlock and keep the headrest unlocked. Push down/pull up the headrest (A) to a position where the shoulder straps are located maximum 1 cm above the child’s shoulders. Lock the harness by first positioning the parts of the buckle that is attached to the shoulder straps (S) together, and then push them into the buckle until you hear a click.
    

11. Pull on the shoulder straps (S) to tighten the harness over your child’s hips. While keeping tension in the shoulder straps (S), pull the harness tension strap (F) straight from the car seat until the harness is tightened enough, you should not be able to fit more than one finger between the shoulder straps (S) and your child’s shoulders.
    

Headrest adjustment

The Axkid MOVEKID is equipped with an adjustable headrest (A).

Always ensure that the headrest is positioned in the correct height for your child when using your Axkid MOVEKID child seat. Check that the shoulder straps (S) are going through the seat straight from your child’s shoulders or maximum 1 cm  above. If not, adjust the headrest (A) accordingly.

Note: The harness tension needs to be released if the headrest cannot be pulled up to a suitable height. Press the belt harness release button (E) to loosen the harness.

Removing Axkid MOVEKID car seat from the vehicle

• Unzip the zipper and open the belt clamp lid (P). Unlock the vehicle seat belt by pressing the red button on the seat belt buckle. Open the belt clamp (O) and pull the vehicle seat belt and guide it through the seat belt slots (D) to remove it from the car seat.
• Unlock the lower tethers (N) by holding on to the connectors with your hand and pressing on the grey button with your thumb. While keeping the connector in your hand, slowly push to extend the lower tethers.
• Push the support leg button (R) and collapse the support leg (Q) to its shortest position.
• Fold the recline angle adjuster (T) to its folded position. Lift the Ax kid MOVE KID out of the vehicle

Tip: Lock the harness buckle and tension the harness before removing the car seat from the vehicle. You can then use the shoulder straps (S) as a carrying handle, making it easier to lift out the car seat and transporting it outside of the vehicle.

Important: Never carry the car seat by holding in the headrest (A).

Recycling your car seat

Ax kid strongly recommends recycling of old car seats. Before leaving the seat at your local recycling station  cut off the harness straps from the seat, remove the textile cover, remove as many Styrofoam parts as possible, separate metal and plastic parts if possible. The main part of the seat should be marked unsafe or expired (use a marker) to deter anyone from using it again. Please check your local municipal guidelines for recycling instructions for the different materials.

Care and maintenance

The seat textile cover can be machine washed at 30º C on a gentle cycle. Do not put the cover in a dryer as this can damage the cover and the padding may separate from the fabric. Visit www.axkid.com to find videos explaining how to remove and attach the cover.

If the textile seat cover needs replacing, ensure only original products from Axkid are used. If other products are used, the Axkid car seat’s safety system may be compromised and could lead to severe injury in case of an accident.

Any plastic parts of the Axkid car seat can be cleaned with mild detergent and water. Do not use aggressive chemicals containing solvents or similar, as this can cause damage to the plastic and compromise the safety of the car seat.

Remove the textile cover:

• Remove the ASIP pad (H) if attached.
• Pull the headrest (A) to its topmost position. Loosen the harness by pressing the harness release button (E) and pull out both shoulder straps (S) at the same time.
• Unzip the two zippers on the underside of the headrest (A) and carefully pull the cover off from the headrest (A).
• Lower the headrest (A) to its lowest position.
• Unlock the harness buckle by pressing the buckle release button (C) and remove the buckle cover.
• Unzip the zipper and open the belt clamp lid (P) and remove the plastic lidfrom the textile cover.
• Open the 4 buttons on the textile cover on the backside of the car seat.
• Unzip the two zippers at the backrest on the inside of the car seat and gently remove the textile cover from the car seat. Be careful around the ASIP pad and other plastic covers to avoid damaging the textile. Don’t pull too hard.
• Open the shoulder pads and gently remove them from the Velcro.

Install the textile cover:

• Reverse the steps from the instruction above to install the textile cover on the car seat again.

Note: The shoulder pads can be installed at different positions. Install them in a position suitable for your child, the shoulder pads should be positioned on top of the shoulder and on the chest of your child. Also make sure that the rubber side of the shoulder pad is facing your child’s chest.

Warranty

The Axkid car seat is covered by a 24-month warranty from date of purchase. Ensure you save your receipt and bring it to your place of purchase if you have any warranty issues.

The warranty does not cover:

• Normal wear and tear.
• Damage due to incorrect use, neglect, or accident.
• If repairs have been carried out by a third party.
• All materials used have a very high UV-resistance rating. However, UV-light is very aggressive and will ultimately lead to fading of the seat cover. This is not covered by our warranty as it is considered normal wear and tear.
• Handle the seat with care. Never carry the seat by holding in the headrest (A).

Sverige/Norge
Axkid AB
www.axkid.com
info@axkid.com
Tel: (+46) 511 760 620

References

• Luna Rear Facing » Axkid
• Beebipood.ee - Lastekaubad, beebikaubad, mänguasjad
• Chameleon – Connecting people with great products and great places
• Los mejores productos de puericultura para tu bebé
• Kotryna Group – Children‘s goods distribution and retail
• Lastentarvike verkkokauppa - Parasta lapsellesi
• Litli Gleðigjafinn
• Βρεφικά Είδη Λητώ - Letoshop.gr
• muki.lv
• tel 011 789 7119
• Safe 'n Sound | Online Baby Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>