BRISTAN MI BAS C Mila Basin Mixer Tap Instruction Manual

: June 4, 2024
: BRISTAN

Table of Contents

Specifications
Prior to Installation
Pack Contents
Installation
Flexible Tail Positions
Operation
Waste Installation & Operation
Maintenance – Clean/Replace Outlet
Maintenance – Cartridge Cleaning
Troubleshooting
General Cleaning
Documents / Resources

Installation Instructions
& User Guide

Please leave these instructions with the end user

Specifications

Tools You’ll Need

Prior to Installation

All products manufactured and supplied by Bristan are safe to use provided that they are installed, operated, and receive regular maintenance in accordance with these instructions.
This product needs to be installed in accordance with, and meet the requirements of the Water Supply (Water Fittings) Regulations 1999 and current by-laws. For full Installation
Requirements & Notes (IRN) please visit wras.co.uk/directory
Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance.
Before installing this product the water supply must be thoroughly flushed in order to remove any swarf, solder etc.
Full access must be made available for future maintenance/ servicing purposes.
This product must not be modified in any way as this will invalidate the guarantee.
If in doubt, contact a registered plumber, your Local Water
Authority or the Secretary of the Institute of Plumbing, address as follows:-
The Institute of Plumbing, 64 Station Lane, Hornchurch, Essex,
RM12 6NB, Tel: 01708 472791

Pack Contents

BRISTAN MI BAS C Mila Basin Mixer Tap - 3

Spare Parts

To replace any spare parts for your tap, why not scan the QR Code or visit www.bristan.com and search for your product?

http://www.bristan.com/search

Installation

BRISTAN MI BAS C Mila Basin Mixer Tap - 5

Flexible Tail Positions

Operation

Waste Installation & Operation

Fit the waste above the basin with the top washer.| Secure waste under the basin with backnut and bottom washer| Push the center down to close the waste. Push again to open and release the contents of the basin.

Maintenance – Clean/Replace Outlet

Maintenance – Cartridge Cleaning

BRISTAN MI BAS C Mila Basin Mixer Tap - 4

Troubleshooting

Symptom	Cause	Remedy
No flow or low flow rate	Partially closed isolation valve.	Open isolation

valve.
Instantaneous water heater cycles on and off as the flow rate or pressure is too low.| Increase water flow rate or pressure through the system.
The Head of water is below the minimum distance required.| Refer to the specification for the minimum distance required.
Hot or cold water being drawn off elsewhere causes pressure changes or instantaneous boiler temperature changes.| Do not use other water outlets when using the taps.
Airlock or partial blockage in the supply pipework.| Flush through pipework to ensure the removal of debris and any airlocks.
Water dripping
from taps| This is normal for a short time after using the taps.| This is caused by residual water tension, the build-up of water in the tap body.
If water continues to drip, possibly due to the ceramic disc valves| Remove valves and clean them, refer to the ‘Maintenance’ section before starting any maintenance.
Taps do not turn
on| Closed isolation valve.| Open isolation valve.
The mains water supply was turned off.| Turn on the mains water supply.

General Cleaning

Bristan products are made from premium materials, with hand polishing and electroplated finishes.
Your taps or shower should be regularly cleaned with warm water, a mild pH- neutral liquid soap, and polished with a soft cloth. Any residues from soap, toothpaste, shampoos, and shower gels can cause blemishes if not rinsed off straight after use.
Household bleaches and cleaners contain harsh chemicals and may damage the surface finish. Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar.
Some surfaces such as nickel and pewter may be affected by the dye found in some cloths, so it is also important to avoid hanging cloths on spouts.
Servicing Your Tap
We recommend servicing your tap at least once every year to prolong its life. To see a video showing how to remove the cartridge for servicing, scan the QR code with your smart phone or tablet.

Alternatively visit www.youtube.com/BristanTV

Our Guarantee

At Bristan, we want to make things as easy as possible for our customers. That’s why we offer solid guarantees on all our products, effective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively, visit www.bristan.com/register. For any other queries, please call our Customer Service on 0330 026 6273 where our expert team of advisors will be able to offer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service- centre/guarantees.

Contact Us
Bristan Group Ltd.
UK: Bristan Group, B78 1SG.
EU: Masco Europe S.à.r.l. 14 Rue Strachen 6933 Mensdorf Luxembourg
Customer Service: +44330 026 6273
Web:www.bristan.com
Email:enquire@bristan.com
A Masco Company
Product Code: MI BAS C (D2)