DENAGO K5242 LCD City Model 1 Top-Tube eBike User Guide
- June 4, 2024
- DENAGO
Table of Contents
- DENAGO K5242 LCD City Model 1 Top-Tube eBike
- Preface
- Appearance and Dimensions
- Function and Button Definition
- Note for Users
- Installation Instruction
- User Settings
- User Settings
- Preparation Before Startup
- FAQ
- Quality Assurance and Warranty Scope
- Appendix 1： Error Code Definition
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DENAGO K5242 LCD City Model 1 Top-Tube eBike
Preface
Dear user, to ensure better performance of your e-bike, please read through the K5242-S product introduction carefully before using. We will use the most concise words to inform you of all the details (including the hardware installation, setting and normal operation use of the display) when using our display. Meanwhile, the introduction will also help you to solve possible confusion and barriers.
Appearance and Dimensions
Material and Color
K5242 products are made of black and white PC. Under the temperature of -20 to
60℃, the shell material can ensure normal usage and good mechanical
performance.
Dimension（unit：mm）
Function and Button Definition
Function description
K5242 provides you with a variety of function modes, to meet your riding needs. Its functions are as follows:
- Battery power indication
- Speed indication
- Distance (including single trip distance and ODO display)
- Walk assist indication
- Backlight setting
- Error code indication
- Various setting parameters
Normal Display Content
Button definition
There are 3 buttons on K5242-BLT, In the following introduction, is named as “MODE”. is named as “UP” and is named as “DOWN”.
Note for Users
Be care of the safety use. Don’t attempt to release the connector when battery is on power.
- Try to avoid hitting.
- Don’t split the waterproof sticker to avoid affecting the waterproof performance.
- Don’t modify system parameters to avoid parameters disorder.
- Make the display repaired when error code appears.
Installation Instruction
When the e-bike is powered off, you can insert the connector of display and the corresponding connector of controller to complete the installation, and adjust the display to a suitable angle.
User Settings
On / Off
Long press “MODE” button then the display will work normally, and the
controller will power on at the same time.
With the display on, long press “MODE” button, the display will shut down, the
display will leave off battery, the leakage current of display on is less than
1μA.
User interface
Walk Assist Mode
Press and hold the “DOWN” button for 2 seconds to enter the Walk assist mode.
The E-bike will travel at a constant speed of 6km/h.
Walk Assist function can only be used as pushing the e-bike by hands. Please don’t use this function when riding.
PAS Level Selection
Short press the “UP” or “DOWN” button to switch the PAS level in the main
interface, the motor output power will be changed accordingly by the PAS level
of E-bike. The default range of PAS level is 0-5 levels. Level 1 is the lowest
output level, and the level 5 is the highest output power level of the motor.
Battery Indicator
The battery power is shown as a percentage bar. When the battery is fully
charged, the power bar shows 100%, each grid represents 10% Battery power.
Speed/Single Trip/Odometer
Real time speed, Trip display interface
When display is powered on, it shows the real-time speed and single trip
mileage interface by default. When the speed is zero, long press “MODE” and
“DOWN” button for 2 seconds, and the current single trip mileage will be
cleared. After the display is shut down and restarted, the single trip mileage
will not be cleared.
Max Speed, Odometer display interface
When display is powered on, short press “MODE” button in the normal interface
to switch the Max speed and Odometer mileage data. The Max speed represents
the maximum speed during this ride, and the Odometer mileage is the total
mileage of the E-bike.
Avg Speed, To Go display interface
Short press “MODE” button again to switch to the Avg speed and To Go mileage
display interface. The Avg speed represents the average speed during this
ride, and the To Go mileage represents the remaining mileage that the E-bike
can go.
Error Code
When the e-bike electronic control system fails, the display will
automatically indicate the error code. For the definition of detailed error
codes, see appendix 1.
The fault can only exited when the fault is eliminated, and the E-bike cannot continue to drive after a fault occurs.
User Settings
When there is no speed in the power on state, press and hold the “UP” and “DOWN” button at the same time for 2 seconds, and the display will enter the setting interface.
Wheel Size Setting
When enter the wheel size setting option. The settable values are: 16, 18, 20,
22, 24, 26, 700C, 27.5, and 28 inch. Select the corresponding wheel diameter
of the E-bike through “UP” and “DOWN” button to ensure the accuracy of the
speed display and mileage display. Long press “MODE” button to return to the
normal interface.
Speed Limit Setting
Short press “MODE” button enter the speed limit setting option. The optional
range of the maximum speed setting is 17Km/h to 45Km/h (11MPH to 28 MPH). It
can be set by “UP” and “DOWN” button. The default setting is 45Km/H (28MPH).
Long press “MODE” button to return to the normal interface.
Backlight Brightness Setting
Short press “MODE” button to enter the backlight brightness setting option.
The setting options: 1, 2 and 3 indicates the backlight brightness, 1 is the
darkest, 2 is standard brightness, 3 is the brightest. The default value is 3.
Long press “MODE” button to return to the normal interface.
Display Unit Setting
Short press “MODE” button to enter the Unit setting option. The setting
parameters are Km/h and Mile/h. Km/h or Mile/h can be selected by pressing
“UP” and “DOWN” button. Km/h means the unit is metric system, and MPH means
the unit is Imperial system. The default setting is MPH. Long press “MODE”
button to return to the normal interface.
Preparation Before Startup
Please read the instruction carefully before using the display.
FAQ
-
Q: Why can’t turn on the display?
A: Please check whether the battery is turned on or the leakage lead wire is broken -
Q: How to deal with the error code display?
A: Contact the e-bike maintenance station in time.
Quality Assurance and Warranty Scope
Warranty Information
-
King-Meter will be responsible for all faults arising during normal operation that are caused by a quality defect.
-
The warranty time is 24 months from the day the display leaves the factory.
The following are not covered by warranty: -
Shell opened.
-
Connector damaged.
-
After display out of factory, the shell is scratched or damaged.
-
Lead wire of display scratch or break.
-
The fault or damage is caused by the force majeure (such as fire, earthquake, etc.) or natural disasters (such as lighting, flooding, etc.)
-
Product exceeded warranty period.
Appendix 1： Error Code Definition
| Error Code | Definition | Solution |
|---|---|---|
| 21 | **** |
Current Abnormal
| Check whether the three phase wires of
the motor are short-circuited
22| ****
Throttle Abnormal
| Check whether the throttle is restored to
the initial state
23| ****
Motor phase problem
| Check whether the phase wires are in good condition;
Check whether the motor phase line is well
connected to the controller
24| ****
Motor Hall defect
| No Hall controller: check whether the phase wire is in good condition
With Hall controller: check whether the
Hall outlet is good
25| ****
Brake Failed
| Check whether the brake lever is reset
before power on.
30| Communication
failure
| Check whether the connection between
display and controller is good
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>