ALLSTAND 20231109 L Shaped Computer Desk Installation Guide
- June 15, 2024
- ALLSTAND
Table of Contents
L Shaped Computer Desk
Instruction Manual
20231109 L Shaped Computer Desk
Note: There is also a more detailed installation video on the product detail page on Amazon.
Subdivision diagram:
Please read the following instructions carefully:
- Some parts of the computer desk have sharp edges, so please be attentive to avoid scratches when installing;
- Due to the small size of the hardware, please put them in a safe position when installing them to avoid accidental;
- In order to avoid giving you a bad installation experience, please follow the steps in the instruction manual to install and carefully distinguish screws and steel strips. If you have a helper, the installation will be certainly easier.
- Allstand offers customers a free lifetime warranty. If you need help regarding product issues, after-sales service or other relevant problems, please contact us via the email provided on the cover.
INSTALLATION INSTRUCTIONS
Note: There is also a more detailed installation video on the product detail
page on Amazon.
Assembly parts list
Installation Steps
Step 1 Assembly steps of the light strip
There are two positions for attaching:
- On the bottom of the shelf 4 .
- On the bottom of the shelf 5 .
Step 2 Assembly steps of the recessed power strip
Attach the 21 part to the corresponding holes of 16 by using I with L .
Step 3 Assembly steps of the monitor stand
Attach 23 to 22 with A , then attach the K part to the corresponding holes of 23 by using J with F .
Step 4 Assembly steps of the computer desk
( Do not fully tighten screws until the end of step 19.)
Step 5
On the basis of step 4, use A to connect 5 through the corresponding holes, holes and finally use E to connect 2 and 5 .
Step 6
( Do not fully tighten screws until the end of step 19.)
Step 7
Fully tighten C screws using wrench F .
Step 8
As shown in the figure, use C to connect 6 7 and 8 9 10 , and finally on this basic, attach 11 to the corresponding holes by using D . (Do not fully tighten screws until the end of step 19.)
Step 9
(Do not fully tighten screws until the end of step 19.)
Step 10
Attach the 18 part to the corresponding holes of step 9 by using A . (Do not fully tighten screws until the end of step 19.)
STOP! SEE BELOW BEFORE PROCEEDING
option 1: Please continue to step 11, 12 & 19.
option 2: Please continue to step 13, 14 & 19.
option 3: Please continue to step 15, 16 & 19.
option 4: Please continue to step 17, 18 & 19.
Step 11 Option 1 assembly
According to the directions of the components in the picture, connect two parts to 13 from the left and right sides with C . (Do not fully tighten screws until the end of step 19.)
Step 12 Option 1 assembly
Step 13 Option 2 assembly
According to the directions of the components in the picture, connect two
parts to 13 from the left and right sides with C .
(Do not fully tighten screws until the end of step 19.)
Step 14 Option 2 assembly
Attach the upper part to the corresponding holes of step 13 by using A and B .
(Do not fully tighten screws until the end of step 19.)
Step 15 Option 3 assembly
According to the directions of the components in the picture, connect two
parts to 13 from the left and right sides with C .
(Do not fully tighten screws until the end of step 19.)
Step 16 Option 3 assembly
Step 17 Option 4 assembly
According to the directions of the components in the picture, connect two parts to 13 from the left and right sides with C . (Do not fully tighten screws until the end of step 19.)
Step 18 Option 4 assembly
Step 19 All options assembly
Fully tighten all screws at the end of this step Use D to connect 19 to each
side of the table, then attach the monitor stand to the corresponding holes of
the table by using J .
Option 1 assembly
Option 2 assembly
Option 3 assembly
Option 4 assembly
https://www.youtube.com/@ALLSTANDOFFICIAL
QR code for installation video
E-mail: support@allstand.net
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>