tp-link 2AXJ4P306 Tapo P306 Smart Wi-Fi Outlet Extender User Guide
- June 15, 2024
- tp-link
Table of Contents
tp-link 2AXJ4P306 Tapo P306 Smart Wi-Fi Outlet Extender User Guide
Images may differ from actual product.
©2023 TP-Link 7106510051 REV1.0.0
Set Up Your Outlet Extender
1 Download Tapo App
Get the Tapo app from the App Store or Google Play.
2 Power Up & Set Up
Plug in your outlet extender. Tap the button in the app and select your model. Follow the app instructions to complete setup.
3 Integrate Third-Party Services
To control your smart plug by voice, go to Me > Third-Party Services in the Tapo app and integrate Alexa, Google Assistant and other third-party services.
Appearance
System LED Status
Button Explanations
More Stable Installation
You can install the outlet extender onto a duplex outlet by using the provided screw and/or the stabilizing post for reinforcement.
Option 1: Via Mounting Screw
- Plug your Tapo device into a duplex outlet.
- Insert the provided screw into the mounting hole and tighten the screw to secure the outlet extender.
An all-pole mains switch in accordance with IEC 62368-1 Annex L shall be incorporated in the electrical installation of the building. And the contact separation of the switch shall not less than 1.5 mm.
Option 2: Via Stabilizing Post
-
Measure the distance between the two outlets of the duplex outlet. CAUTION: Risk of electric shock. Do not insert your
measurement tool into the outlets. -
Insert the stabilizing post into the notch of your outlet extender. Rotate clockwise until it is semi-tightened.
-
Slide the post to the measured distance so that the post can plug into the other outlet. Rotate clock wise to tighten the post.
-
Plug your outlet extender into the duplex outlet.
Note: The removable stabilizing post makes the device fit any type of wall socket, such as a duplex outlet, decorator outlet, USB receptacle, or GFCI outlet.
Safety Notice
- Do not ingest the stabilizing post.
- Plug the product into the wall outlets with earthing connection through the plug.
- Do not use the stabilizing post as a common tool.
- Risk of Electric Shock. Do not allow to be used as a toy. Close attention is necessary when used by or near children to reduce the risk of ingestion of the removed stabilizing post.
- If the stabilizing post is not installed into the outlet extender or removed from the outlet extender, do not place it in reach of children.
CAUTION
- Contains Always On Receptacles. To Reduce the Risk of Electric Shock – Disconnect the equipment from this device before servicing.
- To reduce the risk of fire or electric shock, do not use this device with a receptacle in which the slot openings do not align with the blades.
- To reduce the risk of fire or electric shock, use this device to outlets with a pitch of 38.8 mm ~ 43.8 mm.
Specifications
Need some help?
Visit https://www.tapo.com/support/ for technical support, user guides,
FAQs, warranty & more
FCC compliance information statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1 )This device may not cause harmful interference.
2 )This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located
or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is
applicable to only
Mobile Configurations. The antennas used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter.”
NCC Notice
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>