BRISTAN PA 3199538 Monza Kitchen Mono Mixer Installation Guide
- June 15, 2024
- BRISTAN
Table of Contents
BRISTAN PA 3199538 Monza Kitchen Mono Mixer
Specifications
Inlet Water Temperature
Inlet Connections
Tools You’ll Need
Servicing Your Tap
We recommend servicing your tap at least once every year to prolong its life.
To see a video showing how to remove the cartridge for servicing, scan the QR
code with your smartphone or tablet. Alternatively, visit
www.youtube.com/BristanTV
Before Installation
All products manufactured and supplied by Bristan are safe provided they are installed, used correctly and receive regular maintenance in accordance with these instructions. This product has been tested by the Water Regulations Advisory Scheme (WRAS) and satisfies the requirements of the Water Supply (Water Fittings) Regulations 1999 and current bylaws. For full Installation Requirements & Notes (IRN) please visit wras.co.uk/directory. Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance. Before installing these taps the water supply must be thoroughly flushed to remove any swarf, solder etc. This product must not be modified in any way as this will invalidate the guarantee.
Pack Contents
Flexible Connecting Pipes
Spare Parts
To replace any spare parts for your tap, why not scan the QR Code or visit
www.bristan.com and search for your product?
Installation
If the surface the tap is being fitted to is over 8mm, or you feel the tap needs extra stability, follow the alternative installation steps overleaf.
General Cleaning
Bristan products are made from premium materials, with hand polishing and electroplated finishes. Your taps or shower should be regularly cleaned with warm water, a mild pH-neutral liquid soap, and polished with a soft cloth. Any residues from soap, toiletries etc. should be rinsed off straight after use. Household bleaches and cleaners contain harsh chemicals and may damage the surface finish. Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar. Some surfaces such as nickel and pewter may be affected by the dye found in some cloths, so it is also important to avoid hanging cloths on spouts.
Operation
Alternative Installation for Surfaces Out of Tolerance/Extra Stability
Love Your Chrome
Bristan offers an effective chrome-friendly cleaning kit for use with your
taps and showers. Scan the QR Code or search for ‘CLEAN KIT01’ on
www.bristan.com.
Maintenance – Cleaning/Replacing Outlet
Maintenance – Cleaning/Replacing Cartridge
Troubleshooting
| Symptom | Cause(s) | Remedy |
|---|
No flow or low flow rate
| Partially closed isolation valve.| Open isolation valve.
Instantaneous water heater cycles on and off as flow rate or pressure is too
low.| Increase water flow rate or pressure through system.
Head of water is below the minimum distance required.| Refer to your the
Specification for the minimum working pressure/distance required.
Hot or cold water being drawn off elsewhere causing pressure changes or
instantaneous boiler temperature changes.|
Do not use other water outlets when using the taps.
Airlock or partial blockage in the supply pipework or hoses.| Flush through
pipework to ensure removal of debris and any airlocks.
Water supply failure| Investigate water supply. Check your plumbing and
heating systems for any faults.
Water dripping from taps
| This is normal for a short time after using the taps.| This is caused by
residual water tension, the build up of water in the tap body.
If water continues to drip,
possibly due to the ceramic disc valves/cartridge
| Refer to the Maintenance section or visit www.youtube.com/BristanTV to watch the procedure.
Taps do not turn on
| Closed isolation valve.| Open isolation valve.
Mains water supply turned off.| Turn on mains water supply.
Wobbly Tap
|
Grub screws are not tight enough at the base
| Ensure the grub screws are fully tightened against the base
Extra security may be required depending on the surface the tap is fitted on
to.| Refer to the Alternative Installation steps in order to fit the
Reinforcing Plate.
At Bristan, we want to make things as easy as possible for our customers. That’s why we offer solid guarantees on all our products, effective from the date of purchase, to give you peace of mind. To start your free guarantee simply scan the QR code and register your product. Alternatively, visit www.bristan.com/register. For any other queries, please call our Customer Service on 0330 026 6273 where our expert team of advisors will be able to offer you any help and advice. For full guarantee terms and conditions visit www.bristan.com/service- centre/guarantees.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>