UREVO URTM025 Walking Treadmill User Manual

UREVO URTM025 Walking Treadmill

CUSTOMER SERVICE

IMPORTANT: FOR UREVO ONLY
For damaged or defective product, questions, replacement parts or any other service support, please contact our customer service department by the below methods: [email protected]

• Response Time: 24-48 hours
• Emailing us with the Order ID will be the best method to receive a response during peak business hours.
• Website: www.urevosports.com
• US Support Hotline: (1)844-998-2473

Hours of Operation

• Monday – Frida y : 9 AM – 12 PM; 1 PM – 6 PM (PST)
• PLEASE DO NOT RETURN THIS PRODUCT WITHOUT ASKING OUR CUSTOMER SERVICE FIRST.
• SCAN THIS QR CORD TO GET THE PRODUCT INSTALLATION OR MAINTENCE VIDEOS

IMPORTANT SAFETY INSTRUCTIONS

DANGER :  To reduce the risk of electric shock

1. Always unplug this appliance from the electrical outlet immediately after using and before cleaning.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. An appliance should never be left unattended plugged in. Unplug from outlet when not in use,and before putting on or taking off parts.
2. Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
3. Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons.
4. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
5. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
6. Do not carry this appliance by supply cord or use cord as a handle.
7. Keep the cord away from heated surfaces.
8. Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.
9. Never drop or insert any object into any opening.
10. Do not use outdoors.
11. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
12. Caution – To reduce the risk of injury from moving parts – Unplug before servicing.
13. Warning – To reduce the risk of Electric shock – Unplug before cleaning or servicing.
14. Risk of personal injury – Keep children under the age of 13 away from walking treadmill.
15. To disconnect, turn all controls to the position, then remove plug form outlet.
16. Connect this appliance to a properly outlet only. See grounding instructions.
17. This appliance is not intended for use by persons with reduces physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Keep children under the age of 13 away from this walking treadmill.
18. The maximum weight capacity for this product is 2421bs/110kg. DO NOT EXCEED MAXIMUM WEIGHT CAPACITY.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment­grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

FCC STATEMENT

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
3. This device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with RSS21 0 of Industry Canada. This device complies with Industry Canada license­exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual.
The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
This Class B digital apparatus complies with Canadian ICES-003

SAFETY NOTICE

• Please keep a rear distance of 100 cm or more.
• Please do not stand up on the walking treadmill when it is under auto calibration situation (during 4s after starting). 
• Please choose sneaker.
• Please keep a distance of 0.6 meters or more for both sides.
• Using on uneven ground is prohibited.
• It is strictly forbidden to walk up and down the walking treadmill while walking.
• Please keep your sight horizontal lD 1i’ to avoid dizziness.
• Trampling the treadmill lid ‘DI is prohibited.
• Do not storage as stand up.
• Take care clothing or others debris drawn into appliance when working.
• Please unplug power cord l.D when not in use.
• Do not storage as side  stand.
• Be carefully of elderly and ‘<Y pregnant woman use .
• Single person walking only.
• Do not walking with pets.
• Do not transverse motion.
• Children use MUST be under supervised.
• Do not backward motion.

SPECIFICATIONS

• Model: URTM025
• Weight: 40 kg
• Dimensions: 120 cm x 60 cm x 120 cm
• Maximum User Weight: 120 kg
• Speed Range: 0.5 km/h – 6 km/h
• Power: 220V, 50Hz

PRODUCT AND ACCESSORIES

Please carefully check whether the contents of the package are complete and intact. If there is any missing and damage, please contact the seller.

The Spacewalk E1 Walking Treadmill comes with the following items:

• Walking Treadmill (1 unit)
• Remote Controller (1 unit)
• User Manual (1 unit)

Accessories

PRODUCT INTRODUCTION
The Spacewalk E1 Walking Treadmill is a compact and lightweight treadmill designed for walking exercises. It provides a convenient way to stay active and fit at home or in the office. With its sleek design and user-friendly features, it is suitable for users of all fitness levels.

BEFORE START AND STORAGE

Before using the Spacewalk E1 Walking Treadmill, please ensure the following:

1. Place the treadmill on a flat surface to ensure stability.
2. Connect the power cord to a suitable power outlet.
3. Attach the safety clip to your clothing.

When not in use, follow these steps to store the treadmill:

1. Unplug the power cord from the outlet.
2. Fold the treadmill deck upwards to save space.
3. Secure the folded deck using the locking mechanism.

Take out appliance from packages.

1. Un box and take out accessory box.

2. Lift out appliance and place at flat surface.
   Attention: 2-3 persons assist is necessary.

3. Its normal that visible welding marks residual on walk belt.

Transportation

1. lf transportation needs, unplug power cord and lifting the terminal of appliance.
2. Easy to transport appliance with bottom transportation wheel assists, like as wheelbarrow.

Connect the power

1. Choose flat ground to place the Walking Treadmill. Do not place it on thick and soft cushion.
2. Plug in power cord and switch on power rock button, you can hear a Bi sound from buzzer, its means the circuit of appliance has connected with power electricity.
   Warning: MUST use power cord with comes of package.

Warning:
Before starting to workout with this product, Please assess your physical condition and perform exercise properly and regularly. Incorrect or excessive training can be harmful to your health, If you feel unwell, Stop exercising immediately and consult with your doctor.

FUNTION MENU

Tips: The workout datas (Calorie; Time; Step; Distance; Speed) will be alternated display Per 4 seconds.

REMOTE CONTROLLER

Remote Control Pairing
Long press and turn on the power switch of the walking treadmill at the same time. After 6 seconds, you can hear a beep sound as soon as pairing succeed.

ERROR CODE

When error occurs, error warning indicator will light up and display its error code.

cable whether was pinched or terminal loosen.
E02| The motor wire is loose or failing off, or the carbon brush is worn out.| Check whether the motor cable is loose or failing off. If it does not fall off, check whether the carbon brush of the motor is worn out. If it is worn out, replace the motor. If it is not worn out, the electric controller is damaged. Replace the electric controller.
EOS| Overloading protection|

1. User weight over limited 110KG.
2. Removal foreign bodies which causes of roller or walking belt.
3. Inject lubricants.

E06| System self-check failed.| System failure. Replace controller.
Abnormal display| External disturbance.| Turn off power switch, turn on it after one minute.

Not only error code appeared but also built in buzzer alarm, Once error code and alarm happened, you MUST stop workout immediately, Please contact with after sale service if problem CAN NOT be solved after restart.

TROUBLESHOOTING

HOW TO USE
To use the Spacewalk E1 Walking Treadmill, follow these steps:

1. Stand on the treadmill with your feet centered on the belt.
2. Press the power button on the remote controller to turn on the treadmill.
3. Use the speed buttons on the remote controller to adjust the speed according to your preference.
4. Start walking at a comfortable pace.
5. To stop the treadmill, press the stop button on the remote controller or step off the belt.

CARE AND MAINTENANCE

To ensure the longevity and optimal performance of your Spacewalk E1 Walking Treadmill, please follow these care and maintenance guidelines:

• Keep the treadmill clean by wiping it with a soft cloth after each use.
• Avoid exposing the treadmill to direct sunlight or moisture.
• Regularly inspect and tighten any loose bolts or screws.
• Do not place heavy objects on the treadmill when not in use.

Symptom : walk belt off centered or slips.
Centering walk belt process as follow :

1. Power off appliance and unplug the power cord .
2. Manual centering process as follow:
   • If the walk belt has shifted to left, use the hex tool to turn the left idler roller screw clockwise 1/4 of a turn(refer to figure 1 ).
   • If the walk belt has shifted to right, use the hex tool to turn the right idler roller screw clockwise 1/4 of turn(refer to figure 2).
3. Appliance MUST work 1-2mintutes. Repeat manual centering process untill the walk belt is centered.

Belt slip correcting process as follow :

1. Power off appliance before operation.
2. Using the hex tool, turn both idler roller screws clockwise 1/2 of turn(refer to figure 3).
3. After corrected, please attempts to walking 1-2 minutes under 1.0 mph speed setting. Repeat until the walk belt is properly tightened.

Attentions

1. To prevent any injury, don’t place any debris around appliance before maintenance process.
2. MUST use associated hex tool.
3. Take care at maintenance process. Do not pinch fingers.

Belt lubrication process, follow instruction below to lubricate belt.

1. Power off appliance and unplug cord.

2. Using the hex tool, turn both idler roller screws counterclockwise till belt loosen and lifting easily.
   Tips: please markdown hex tool rotating cycles when loosen belt, which use for adapting belt tension after lubrication process.

3. Lifting edges of belt and spraying lubrication oil at center of walk platform evenly. Not necessary to apply spray lubrication oil on entire walk platform.

4. Lubrication oil volume Per time of maintenance: 5-10ml.
   Attention: it would causes of belt slip if spray too much.

5. Using the hex tool, turn the both idler screws clockwise as previous markdown number of turns untill walk belt tighten properly.

6. Power on appliance and workout for a few minutes, in order to spread lubrication oil to whole belt surface evenly.
   Attention: No-loading work at 1.0mph speed setting.
   Lubrication frequency: High recommend 125 Miles Per time.

Appliance cleaning.

1. Power off appliance and unplug power cord before cleaning.
2. Wipe and clean with damp cloth, Do not cleaning with acidic or caustic detergents.
3. Do not clean opposite of walk belt.
4. Its normal few black powders residual under appliance after long working.

WARRANTY **

**

The Spacewalk E1 Walking Treadmill comes with a one-year warranty from the date of purchase. The warranty covers manufacturing defects and does not cover damage caused by improper use or unauthorized modifications. For warranty claims or inquiries, please contact our customer service department.

MANUFACTURER’S LIMITED WARRANTY
UREVO warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with UREVO Owner’s Manual. UREVO’s obligation under this warranty applies to the following:

COMPONENT LENGTH OF WARRANTY
Structural Frame 1 year For Home Use Only All Other Components 90 days For Home Use Only

Exclusions from Warranty Coverage:
UREVO does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any product failure, product malfunction, or damages attributable to:

1. Improper installation and/or failure to abide by UREVO’s installation guidelines;
2. Use of this product beyond normal home use, or in an application for which it was not designed;
3. Cosmetic items such as scratches, dents or discolorations;
4. Damage caused by normal wear and tear, vandalism, accidental or by animals;
5. Any act of Nature (such as fire, flooding, snow, ice, hurricanes, earthquakes, lightnings or other natural disasters), environmental condition (such as air pollution, mold, mildew, etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);
6. Normal weathering due to exposure to sunlight, weather and atmosphere which can cause colored surfaces to among other things, flake, chalk, accumulate dirt or stains.
7. Improper operation, alteration, handling, storage, abuse or neglect of the products.

UREVO , using its sole discretion, will either repair or replace free of charge any part(s) proven to be defective under normal home use. Any repair or replacement shall provide no new warranty coverage, but shall retain only the remaining portion of the original product’s warranty. This warranty is offered only to the original purchaser and is not transferable. Proof of original purchase is required.

When ordering replacement parts please have the following information ready

1. Order Number
2. Description of Parts (Adding photos or videos would be helpful)
3. Part Number
4. Date of Purchase

FAQ

1. Q: Can I run on the Spacewalk E1 Walking Treadmill?
   A: No, the Spacewalk E1 Walking Treadmill is designed for walking exercises only. Running or jogging on this treadmill may cause damage and void the warranty.

2. Q: What is the maximum weight limit for users?
   A: The maximum user weight limit for the Spacewalk E1 Walking Treadmill is 120 kg.

3. Q: Can I use the treadmill without the remote controller?
   A: No, the remote controller is necessary to operate the Spacewalk E1 Walking Treadmill. It allows you to adjust the speed and control various functions.

IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
Manufacturer: Shenzhen Vile Dynamic Technology Co., LTD.
Address: 1205-1206, Tianliao Building, Tangchang Road, Tanglang Community, Taoyuan Street, Nanshan District, Shenzhen, China

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>