SPALDING M6E11E02 Portable Basketball System

Product Information

• Model Number: [Model Number]

Toll-Free Customer Service Number:

• U.S.: 1-800-558-5234
• Canada: 1-800-284-8339
• Europe: +353 51 379777
• Australia: 1300 367 582

Website: www.spalding.com

Warning
READ AND UNDERSTAND THE OPERATOR’S MANUAL BEFORE USING THIS UNIT. FAILURE TO FOLLOW THE OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.

Contents

Questions or Missing Parts?

• DON’T go back to the store!
• Call the TOLL-FREE Customer Service Number listed on the front page!

Before You Begin

Warning
FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR PROPERTY DAMAGE.

Contact

Questions or missing parts?

Email:

• Customer Service: warrantyservice@custserv.fotlinc.com
• Spalding Parts: SpaldingParts@spalding.com

Toll-Free Number:

• U.S.: 1-800-558-5234
• Canada: 1-800-284-8339
• Europe: +353 51 379777
• Australia: 1300 367 582

Mailing Address:

• U.S.: Spalding PO Box 90015 Bowling Green, KY 42102
• Canada: [Mailing Address]

Warranty
For the very latest Basketball System Warranty information, please visit www.Spalding.com or call Spalding Customer Service at 1-800-558-5234.

Safety Information

Warning
Most injuries are caused by misuse and/or not following instructions. Use caution when using this unit.

Notice
Backboard style will vary.

Package Contents

Primary Assembly Components:

• 1 Primary Sub-Assembly (x1)

• 2 Extension Arm (x1)

• 3 Backboard Assembly (x1)

• 4 Rim (x1)

• 5 Rim Cover, Orange (x1)

• 6 Front Cover (x1)

• 7 Knuckle Shroud (x1)

• 8 Bolt, Hex, 3/8-16 x .625 (x4)

• 9 Rim Bracket (x1)

• 10 Bolt, Hex, Flange, 5/16-18 x 1 (x4)

• 11 Nut, Wiz, 5/16-18 (x4)

• 12 T-Bolt (x1)

• 13 Spring (x1)

• 14 Nut, Special (x1)

• 15 Washer, Flat, 1.5 OD (x1)

• 16 Bracket, Reinforcement (x1)

• 17 Screw, #10-0.394 Long (x2)

• 18 Washer, .375 ID (x2)

• 19 Nut, Acorn, Locking, 5/16-18 (x2)

• 20 Pull Pin (x1)

• 21 Bolt, Hex, 1/2-13 x 4.5 (x1)

• 22 Nut, Nylock, 1/2-13 (x1)

• 23 Bolt, Carriage, 1/4-20 x 1.5 (x8)

• 24 Knob, 1/4-20 (x8)

• 25 Thumbscrew, M8 x 1.25 (x2)

• 26 Handle Assembly (x1)

• 27 Pull Pin, Handle (x1)

• 28 Plug, Base (x2)

• 30 Washer, Flat, 1/4 (x2)

• 31 Cover, Extension Arm (x1)

• 32 Screw, 1/4 x 0.75 (x2)

Tools & Materials for Assembly

• Safety Glasses
• Socket Wrench 1/2, 9/16, 3/4
• Wrench 1/2, 9/16, 3/4
• Phillips Screwdriver
• Sand/Garden Hose
• Step Ladder (8 ft.)
• (OPTIONAL) Adjustable Wrenches

Assembly Overview
Refer to the user manual for detailed assembly instructions.

• Rim (Section D)
• Backboard (Section B, C)
• Extension Arm Cover (Section H)
• Pole (Section E)
• Front Cover (Section F)
• Crank Handle (Section G)
• Base (Section A)

Fill the Base

Required Parts:
Completed Base Assembly

A FILL THE BASE
Roll the primary sub-assembly to the desired location for use.

FAQ

Q: What should I do if I have missing parts or questions about the product?
A: Contact our Customer Service through email or the toll-free number provided in the user manual.

Before You Begin

READ AND UNDERSTAND THE OPERATOR’S MANUAL BEFORE USING THIS UNIT.

• Remove ALL contents from boxes.
• This manual, accompanied by a sales receipt, should be saved and kept on hand as a convenient reference, as it contains important information about your model.

WARNING
FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR PROPERTY DAMAGE.

Contact
Questions or missing parts? Do NOT go back to the store!

Email:

| U.S.: warrantyservice@custserv.fotlinc.com Canada: SpaldingParts@spalding.com
---|---
Customer Service Toll-Free Number:| U.S.: 1-800-558-5234
Canada:          1-800-284-8339
Europe:          +353 51 379777
Australia:         1300 367 582
Mailing Address:| Spalding PO Box 90015 Bowling Green, KY 42102

Warranty

For the very latest Basketball System Warranty information, please visit www.Spalding.com or call Spalding Customer Service at 1-800-558-5234.

Safety Information

WARNING

FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID THE WARRANTY. Owner must ensure all players know and follow these rules for safe operation of the system.

To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check the entire box and inside all of the packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document. Proper and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly.

• If using a ladder during assembly, use extreme caution.
• Check the base regularly for leakage. Slow leaks could cause the system to tip over unexpectedly.
• Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections to separate during play and/or during transport of the system.
• Climate, corrosion, or misuse could result in system failure.
• If technical assistance is required, contact Customer Service.
• Minimum operational height is 6′-6″ (1.98 m) to the bottom of backboard.

Most injuries are caused by misuse and/or not following instructions. Use caution when using this unit.

NOTICE

• Adult assembly required.
• Dispose of ALL packaging materials promptly.
• As with all products, periodically inspect for loose, small parts.
• Assembled unit MUST be filled with sand or water at ALL times.
• ALL basketball systems, including those used for DISPLAYS, MUST be assembled and installed according to instructions.
• Failure to follow instructions could result in SERIOUS INJURY.
• It is NOT acceptable to devise a makeshift support system.

Package Contents

Check the contents of each kit and other parts to ensure that all components are present. Keep the kit hardware in the labeled bag as they will be used in different assembly steps.
See “Parts List” on page 23 for a complete list of replacement part numbers.

PRIMARY ASSEMBLY COMPONENTS

KIT 2 – 209221

KIT 3 – 209242

KIT 4 – 209184

KIT 5 – 209224

KIT 6 – 209225

Tools & Materials for Assembly

Assembly Overview

Assembly

Fill the Base

Required Parts:/Completed Base Assembly:

• SAND/GARDEN HOSE

FILL THE BASE

1. Roll the primary sub-assembly to the desired location for use.
2. Fill the base with water (approx. 36 gallons (136 Liters)) or sand (approx. 300 lbs. (136 kg)).
3. Insert the cap (28) into the base to close.

NOTE
As base is being filled, you may monitor the fill status and proceed with Assemble the Extension Arm, Assemble the Backboard, and Assemble the Rim sections. DO NOT proceed with Assemble the Upright section until base is completely filled.

WARNING

• FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
• THE CAP MUST BE TIGHTENED COMPLETELY AND SECURELY TO PREVENT LEAKAGE.
• CONTACT CUSTOMER SERVICE IMMEDIATELY IF THE CAP IS MISSING OR DAMAGED.
• CHECK THE WATER LEVEL BEFORE EACH USE.

Assemble the Extension Arm

• KIT 1
• WRENCHES AND/OR SOCKET WRENCHES (9/16″)

INSTALL THE EXTENSION ARM

1. Attach the extension arm (2) to the middle pole using the hex bolts (8).
2. Tighten the hex bolts (8) in the pre-welded nuts on the pole.

Assemble the Backboard

• KIT 2
• WRENCHES AND/OR SOCKET WRENCHES (1/2″)

IMPORTANT
CAREFULLY CUT AND PEEL THE PROTECTIVE FILM AWAY FROM THE BOARD BEFORE ATTACHING THE RIM.

INSTALL THE BACKBOARD

1. Insert the t-bolt (12) through the rim bracket (9).
2. Secure the rim bracket (9) to the backboard (3) and extension arm (2) using the bolts (10) and nuts (11).

Assemble the Rim

• KIT 3
• WRENCHES AND/OR SOCKET WRENCHES (3/4″)
• PHILLIPS SCREWDRIVER

ASSEMBLE THE GOAL

1. Fit the rim (4) securely into the rim bracket (9). Allow the t-bolt (12) to slip through the center hole in the rim (4).
2. Install the reinforcement bracket (16) onto the t-bolt (12). ASSEMBLE THE GOAL
3. Install the spring (13) onto the t-bolt (12).
4. Install the special nut (14) and washer (15) onto the t-bolt (12).
5. Tighten the nut (14) until 1/8″ of the bolt threads onto the exposed end of the t-bolt (12).
6. Attach the cover (5) to the rim (4) using the cover screws (17).

Assemble the Upright

• KIT 4
• WRENCHES AND/OR SOCKET WRENCHES (1/2″; 3/4″)

WARNING
TWO PEOPLE ARE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.

ASSEMBLE THE POLE STRUTS

1. From the front of the unit, rotate the pole assembly upward. A second person must support the backboard (3).
   IMPORTANT
   DURING STEPS 1-2, THE SECOND PERSON SUPPORTING BACKBOARD ONLY NEEDS TO LIFT TOP EDGE OF THE BACKBOARD APPROXIMATELY 18″ FROM THE GROUND. AFTER STEP 2 IS COMPLETED, THE SECOND PERSON MAY GENTLY LOWER THE BACKBOARD BACK TO THE GROUND.

2. After rotating the poles up, rotate the struts into the threaded studs on the base.

3. Secure the struts in place with a washer (18) and nut (19).

4. Attach the extension arm cover (31) to the extension arm using screws (32) and washers (30).
   NOTE
   The top edge of the backboard should rest on the ground for this assembly.
   WARNING

   • ENSURE THE BASE IS FILLED.
   • TWO CAPABLE ADULTS ARE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY.
   • DO NOT LEAVE THE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER.

5. Carefully rotate the pole into the upright position.

6. Insert the pull pin (20) through the front hole.

7. Insert the hex bolt (21) and secure it with the nut (22). Tighten completely.
   IMPORTANT
   YOU MAY NEED TO SLIGHTLY ADJUST THE POSITION OF THE PRIMARY UPRIGHT TO ACHIEVE PROPER HOLE ALIGNMENT FOR BOLT INSERTION. GENTLY PUSH THE UPRIGHT BACK AND FORTH UNTIL PROPER CLEARANCE FOR BOLT INSERTION IS ACHIEVED.

8. Tighten the bolt and nut on the outside of the struts.

Assemble the Front Cover

• KIT 5

IMPORTANT
ENSURE ALL CARRIAGE BOLTS ARE INSERTED PRIOR TO TIGHTENING COMPLETELY.

1. Attach the front cover (6) to the struts using carriage bolts (23) and tri-knobs (24).
2. Attach the knuckle shroud (7) using the carriage bolts (23), tri-knobs (24), and thumbscrews (25).

IMPORTANT
ENSURE ALL CARRIAGE BOLTS AND THUMBSCREWS ARE INSERTED PRIOR TO TIGHTENING COMPLETELY.

Assemble the Handle Assembly

• KIT 6

INSTALL THE HANDLE ASSEMBLY

1. Attach the crank handle assembly (26) and pull pin (27).
2. Apply the Height Adjustment and Moving Label (29) to the front of the pole, where it is clearly visible.

Operation

ADJUSTING THE HEIGHT

WARNING
DO NOT ALLOW CHILDREN TO ADJUST THE HEIGHT.

1. Insert the pull pin (27).
2. Crank the handle (26) to adjust up or down to the desired height.
3. Replace the pull pin (27) to lock in place.

MOVING THE UNIT

1. Lower the backboard height to the lowest position.
2. Grasp the pole and tilt the system until the wheels of the base engage with the ground.
3. Roll the system to the desired location.
4. Tilt the basketball system into the upright position and check the system for stability.

Parts List

SAFETY LABELS

NOTICE
APPLY THE SAFETY LABELS TO THE COMPLETED ASSEMBLY PRIOR TO USE.

WARNING

• READ AND UNDERSTAND THE WARNINGS LISTED BELOW BEFORE USING THIS PRODUCT.
• FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.

The owner must ensure that all players know and follow these rules for the safe operation of the system.

• DO NOT hang on the rim or any part of the system including the backboard, support braces, or net.
• During play, especially when performing dunk-type activities, use caution to keep your face away from the backboard, rim, and net. Serious injury could occur if teeth/face come in contact with the backboard, rim, or net.
• DO NOT slide, climb, shake, or play on base and/or pole.
• After full assembly, fill the system with water or sand. Never leave the system in an upright position without filling the base with weight, as the system may tip over, causing injuries and/or property damage.
• DO NOT add ballast on top of the base (such as sandbags or cinder blocks). Such added ballast can crack the base, causing leakage, which could cause the system to tip over. DO NOT use ballast on top of the base as a substitute for filling the base with water or sand.
• When adjusting the height or moving system, keep hands and fingers away from moving parts.
• DO NOT allow children to move or adjust the system.
• DO NOT wear jewelry during play (rings, watches, necklaces, etc.). Objects may entangle in net.
• The surface beneath the base must be smooth and free of gravel or other sharp objects. Punctures or cracks in the base could result, causing leakage which could cause the system to tip over.
• Keep organic material and water away from the pole base. Grass, water, litter, etc. could cause corrosion and/or deterioration.
• Keep the pole top covered with a cap at all times. Water and debris entering the pole through the uncapped top can cause corrosion from the inside.
• CHECK pole system for signs of corrosion (rust, pitting, chipping) and repaint with exterior enamel paint. If rust has penetrated through the steel anywhere, replace the pole immediately.
• CHECK system before each use for proper ballast, loose hardware, excessive wear, and signs of corrosion; replace or repair before use.
• CHECK the system before each use for instability.
• DO NOT use or leave the system upright during windy and/or adverse weather conditions; the system may tip over. Place system in the storage position and/or in an area protected from the wind and weather, and free from personal property and/or overhead wires.
• Never play on damaged equipment.
• See the instruction manual for proper assembly and maintenance.
• When moving the system, use caution to keep the height adjustment mechanism from shifting.
• Do not allow water in the tank to freeze. During sub-freezing weather add 2 gallons of non-toxic antifreeze or sand, or empty the tank completely and store. (Do not use salt.)
• DO NOT allow anyone to stand or sit on base while moving the system.
• DO NOT leave the system unsupervised, or play on the system when wheels are engaged for moving.
• Use caution when moving the system across uneven surfaces. The system may tip over.
• Use extreme caution if placing the system on a sloped surface. The system may tip over.

WARNING LABELS AND INSTRUCTIONS MUST ACCOMPANY THIS PRODUCT. CALL TOLL-FREE FOR REPLACEMENT: 1300 367 582 (AUSTRALIA) www.spalding.com.au.

WARNING:
SWINGING ON THE RING MAY CAUSE SERIOUS INJURY OR DEATH

CAUTION:
THIS BACKBOARD AND RIM IS NOT DESIGNED TO SUPPORT A PLAYER HANGING FROM THE RIM OR NET. FAILURE TO OBSERVE THIS CAUTION MAY CAUSE BODILY INJURY AND/OR PROPERTY DAMAGE.

WARNING LABELS AND INSTRUCTIONS MUST ACCOMPANY THIS PRODUCT. CALL TOLL-FREE FOR REPLACEMENT:

• 1.800.558.5234
• www.huffysports.com
• www.spalding.com.

© Copyright 2022 by Russell Brands, LLC. www.Spalding.com.

References

• Fruit of the Loom Home
• Spalding. Made for the Game. | Spalding.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>