HOLOTAG T1 Fallout Brotherhood of Steel User Manual

: June 15, 2024
: HOLOTAG

Table of Contents

T1 Fallout Brotherhood of Steel
HOW IT WORKS
REQUIREMENTS
BATTERY
PRIVACY
CUSTOMER SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Model: T1
User Manual

T1 Fallout Brotherhood of Steel

HOLOTAG T1 Fallout Brotherhood of Steel - app

HOLOTAG T1 Fallout Brotherhood of Steel - Overview

Hanging Holo
Buzzer
Button
Battery Cover
Serow
Replaceatle CR2032 Battery

HOW IT WORKS

HOLDTAG (T1) is gtway to kesp track o your belongings nd give you peaca of mind knawing that can fdthem. Tough the use of Blustooth Low Enargy (BLE, uou an it your missing tems with the help of nearoy Agple davices that are part o the Apple Find My network

REQUIREMENTS

To use the Find My app to locate this item, the latest version of iOS, iPadOS, or macOS is recommended.

SETTING UP YOUR HOLOTAG (T1) FOR THE FIRST TIME

Remove the insulating pull tab to activate the battery;
Press the button once, and then immediately press again & hold the button for approx. Ss to enter the pairing state. You will hear a long beep followed by a start-up tone;
Open the Find My app on your iPhone or iPad, choose the “Items” tab > tap “+” to add Item > tap “Add Other Item”.

After setup, you can locate your T1in the Find My app on your iPhone, iPad, iPod touch, or Mac. If T1 is not added to the Apple ID within 10 minutes after reset, the Bluetooth will stop transmitting signals to save power. You can wake up T1 and enter the pairing state by pressing the T1 button once. At this time, you can start adding the device again.
A 71 that has been added to an Apple ID must be removed from the Find My app and unlinked from the Apple ID before it can be reset and added to another Apple ID.
If T1 cannot be added, or if the pairing process is interrupted, you can reset T1 using the button and then pair it again.

BATTERY

This product has a replaceable CR2032 battery that will last up to 18 months. When the battery runs out you can replace it in 3 simple steps:

Loosen the screw (not removable), rotate the battery cover counterclockwise all the way with a coin, and then open the battery cover;
Replace the battery with a new CR2032 type battery, placing the battery positive side up;
Close T1 by aligning the dots on the battery cover and bottam case.

It is recommended to use Panasonic or Maxell CR2032 batteries because they are known for their long battery life and reliability.

PRIVACY

The Apple Find My network uses advanced encryption to ensure that no one else, not even Apple or HoloMarg can view the location of your T1.
To use the Apple Find My app to locate this item, the latest version of iOS, iPadOS, or macOS is recommended. The Find items app on Apple Watch requires the latest version of watchOS.
Use of the Works with Apple badge means that a product has been designed to work specifically with the technology identified in the badge and has been certified by the product manufacturer to meet Apple Find My network product specifications and requirements. Apple is not responsible for the operation of this device or use of this product or its compliance with safety and regulatory standards.
Apple, Apple Find My, Apple Watch, Find My, iPhone, iPad, iPadOS, Mac, macOS and watchOS are trademarks of Apple Inc. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
FCC WARNNINGS
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may Cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this device not expressly approved by Shenzhen Rundian Innovation Technology Co. Ltd. may void the FCC authorization to operate this device.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
Contains FCC ID: 2BDG4-T1
RF exposure statement:
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device is installed and operated without restriction.
Industry Canada Notice
This device contains licence-exempt transmitter[s)/receiver(s] that comply with Innovation, Scienceand Economic Development Canada’s licence-exempt RSS[s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may Cause undesired operation of the device.

WARNING
KEEP OUT OF REACH OF CHILDREN
Swallowing can lead to chemical bums, perforation of soft tissue, and death. Severe burns can occur within 2 hours of ingestion. Seek medical attention immediately.