HANDLEIDING AG230 Bluetooth Speaker User Manual

HANDLEIDING AG230 Bluetooth Speaker

Warning

• Read this user manual carefully first to ensure correct use and trouble-free operation.
• For the first use, a full charge is recommended.
• Use and store the product at room temperature.
• Do not throw the product and let it fall to prevent damage.
• Do not expose the product to fire, high temperatures, direct sunlight, etc.
• Do not use organic solvents or other chemicals to clean the product.
• Do not let small particles get into the product.
• Keep the volume of the speaker moderate to prevent temporary or permanent hearing damage.
• Do not disassemble the product and do not make changes to the structure.
• Keep the product out of reach of children.
• If the battery is not replaced correctly, an explosion may occur, never replace the battery yourself.
• Batteries (accumulators) should not be exposed to circumstances such as sunshine, fire, or similar situations of overheating.

Included Parts

• 1 x Bluetooth Speaker
• 1 x User Manual
• 1 x USB Type-C Charging Cable
• 1 x 3.5mm Audio Cable
• 1 x Strap

Button Functions

Short press:

 increase volume

Long press:

 play the next song

Short press:

 decrease volume

Long press:

 play the previous song

Play/Pause Button:

 Short press to play or pause.

Incoming Call Button:

 Short press to answer the call. Long press to reject.

Mode Button:

 Short press to change mode. If a Micro SD card, USB flash drive, and an audio cable are plugged into the device, the mode sequence will be: Bluetooth mode → Micro SD card mode → Aux-in mode → USB mode. Hold the button for 2 seconds to disconnect the connected device.

RGB Light Mode (colored lights):

 Double-click the mode button to switch the RGB light on/off or to change the color.

Port Functions

Aux Input:

 If an aux cable is connected, the speaker will switch directly to AUX mode.

USB Input:

 If a USB stick is connected, the speaker will switch directly to USB mode.

USB Type-C Charging Port:

 Use a DC 5V / 2A adapter to charge the AG230.

Charging Indicator:

 The red light will remain on while the AG230 is charging. Remove the cable after it is fully charged.

Connecting with Bluetooth

1. Turn on the speaker by holding the power button for 2 seconds.
2. Connect with your device by turning on Bluetooth and selecting AG230. Once connected, you will hear a beep and the blue light will remain on. The AG230 speaker will automatically connect with the last paired device once Bluetooth is enabled.

Other instructions: To connect with another device, hold the M button for 2 seconds. This will disconnect the current device so a new one can be paired.

Stereo Function: Connect Two AG230 Speakers

1. Turn on both speakers and make sure they are not connected to any device. Press the “-” and “+” buttons on one of the speakers simultaneously. A beep indicates that the speakers are paired. Once paired, you will hear another beep.
2. Select AG230 in the Bluetooth settings of your Bluetooth device. You will hear a sound indicating a successful connection and the blue light will stay on.
3. To disconnect the speakers, press the “-” and “+” buttons on either speaker at the same time.

Tips: The speaker where you first press the “-” and “+” will act as the main speaker. After setting up the Stereo system, only the main speaker needs to be controlled to operate both speakers simultaneously.

Specifications

Basic Parameters

Speaker Type| Portable Bluetooth Speaker
Supported Storage| Up to 32 GB Micro SD Card
Power Supply| Built-in 8000 mAh Lithium Battery
Audio Input| Bluetooth, Micro SD Card, 3.5mm Aux in
Technical Parameters
Loudspeaker| Dual 66mm Speakers + Dual 78mm Low Frequency Amplifiers
Frequency| 60Hz ~ 18KHz
Bluetooth Version| Bluetooth 5.0
USB Standard| USB 2.0 (Compatible with USB1.1)
Supported Media Type| APE/ FLAC/ WAV/ WMA/ MP3
Bit Rate|

• MP3: 8Kbps-320Kbps
• WMA: 32Kbps-384Kbps
• WAV: 32Kbps-1414Kbps
• APE: 100Kbps-1200Kbps
• FLAC: 100Kbps-1200Kbps

Dimensions| 250106115 mm
Weight| 1173g (including the built-in lithium battery)

Troubleshooting

FAQ ProblemSolutionI cannot connect my device:

1. Restart the speaker and try again.
2. If your device asks for a code, enter 0000.

Playback is stuttering or stops:Ensure the speaker is within the working range and there are no obstacles between the speaker and the device.Cannot play music from a Micro SD card:

1. Make sure the format of the Micro SD card is FAT32. The speaker only supports FAT32 Micro SD cards.
2. Ensure the music files are in APE, FLAC, WAV, WMA, or MP3 format.

No sound during playback:

1. Adjust the volume of the speaker.
2. Adjust the volume of your device.
3. Check if the speaker is paused.

No sound in AUX mode:Ensure the audio cable is properly connected.Cannot turn on:Try charging the speaker for about 3 hours.No response from controls, how to reset?Hold the power button for 8 seconds to reset the speaker.

Product Visualization

The AG230 is a portable Bluetooth speaker equipped with a strap for easy carrying. It is shown in two scenarios: one with a beautiful sunset in the background, highlighting the speaker’s rugged outdoor use, and another showing the speaker with water splashing around it, suggesting its water-resistant properties.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>