tuya SIB Solar Wireless Beam Detector Installation Guide

SOLAR WIRELESS BEAM DETECTOR
INSTALLATION GUIDE

5SW(5m)
10SW(10m)
30SW(30m)
60SW(60m)
400SW(100m)

SIB Solar Wireless Beam Detector

Caution: Thanks for your purchasing this product; Please Read this manual carefully before using
This product can sense illegal entering and sound an alarm, but it cannot prevent the burglary and other disasters.

1. Our company will not be responsible for the losses caused by negligence, abuse, natural disaster, lightning or use not in accordance with the user’s manual.
2. There are copyright contents of our company in this user’s manual, so you may not copy without our company’s permission, meanwhile, please store it appropriately.
3. The guarantee period is 12 months since production date.
4. Our company will be responsible for repairing or replacing the damaged parts caused by product quality within the period of guarantee. This warranty does not cover the other damages or following provisions.

• Damages caused by improper use
• Damages caused by repair or replacement of our company
• Damages caused by natural disaster etc force majeure factor.
• Malfunctions unrelated to this product.

Part Name

Precautions for setting

• Multi sensors may be used for long-distance guarding. Please install according to the below diagram to avoid interference between beams.

Model| Guarding distance| Beam spread diameter|
---|---|---|---
5SW| 50m| 1.8m
10SW| 10m| 2.2m
30SW| 30m| 2.8m
60SW| 60m| 3.7m
100SW| 100m| 4.5m

Parts diminution

Installation of fixed bracket

1. Loose the retaining screws on the housing and remove it. (As below diagram).
2. Insert the batteries onto the circuit board and the indicator will be flashing 5 secs to show it’s working.
3. Loose the retaining screws on the mounting plate, then remove the mounting plate and do not touch the sensitive lens by hand, mount the mounting plate on the pole or wall. (As below diagram)

Optical axis adjustment

Note: Perform the optical axis adjustment for the transmitter and receiver due to the alignment of optical axis may bring a great change to sensitivity.

1. Rotate the bottom of lens on the receiver from left to right to ensure that the lens shall face to the transmitter correctly.
2. Rotate the bottom of lens on the transmitter from left to right to ensure that the lens shall face to the receiver correctly, align the optical axis to obtain sensitivity, secure the lens on the transmitter after aiming the transmitter towards the receiver through aiming unit.
3. Adjust the horizontal adjusting knob and vertical adjusting knob on the transmitter until you can see the receiver is located on the central position of aiming unit of transmitter through the aiming unit of transmitter.
4. Adjust the horizontal adjusting knob and vertical adjusting knob on the transmitter until you can see the transmitter is located on the central position of aiming unit of receiver through the aiming unit of receiver.
5. When adjusted fine, the LED indicator of the receiver will be flashing for 10 secs and keep on for 5 secs then off. Check if working well- Block the beams between the transmitter and receiver the prewarmed control panel will be alarming, the LED of receiver will be on for 3 secs and the flashing for matching again.
6. Cover the solar housing and fasten the screws to finish the installation.

1. Power indicator, when power on it will flash for 5 secs then go off.
2. Adjusting & Alarm indicator, when it receives infrared beam it will flash, if matches well, it will be on for 3 secs. When alarm it will be on for 5 secs and then go off.

Physical test

Walking test is required after the setting, physical test in accordance to below diagram.

| State| Signal
---|---|---
Transmitter| Transmitting| Power on flash 5 secs then off
Receiver| Guarding| Flash 10 secs then on 3 secs then off
In alarm| On for 5 secs then off
Control panel| In alarm| Sound alarm as setting

Maintenance

1. Replace battery
   The battery using life is 2 years, please replace battery within the time.

2. Protect and Clean
   The solar power panel might be dirty after long use, please keep checking and cleaning the panel in certain time to have the detector working well. (Note: Do not wet the circuit board when cleaning.)

Trouble checking

Replace the battery
The LED of the transmitter doesn’t light up| Battery power low or broken| Replace the battery
When 2 beams blocked simultaneous, the receiver indicator is on for 2-3 secs but no alarm signal output to the wireless control panel| Abnormal signal receiver for the control panel
The receiver is too far away from the control panel studied to the zone of the control panel| Check whether the detector has been
Place the control panel nearer to the receiver or add a signal repeater
There are always alarm signal output from time to time when nobody block the beams| There are obstacles between the transmitter and the receiver
The base on which the bracket mounted is not steady
The transmitter and receiver not match well| Remove the obstacles
Remount the transmitter and receiver to steady base
Re-adjust the beams

Technical Parameters

Model| 5SW| 10SW| 30SW| 60SW| 100SW| | |
---|---|---|---|---|---|---|---|---
Alert distance (Outdoor)| 5m| 10m| 30m| 60m| 100m| | |
No. Of beams| 2 beams
Detection mode| 2 beams blocked simultaneous
Optical source| Infrared digital pulse beam
Response speed| 50msec
Alarm output| Wireless RF alarm signal
Power supply| Solar power
Power consumption| ≤0.4mA on the transmitter, ≤0.4mA on the receiver
RF frequency| 433MHZ/315MHZ ASK
RF transmission| Up to 500m in the open space
Operation temperature & humidity| -25°C–55°C 5%-95%RH(relative humidity)
Dimensions| Refer to its diagram
Recharge currency by solar board| ≥1mA under 1600Lx( More than 2000Lx in normal cloudy day)
Optical axis adjustment(H,V)| 180° H (± 90° ) 120° V (± 10°)
Protection against dew, frost| Calefaction housing(optional)
Material| PC Resin
Net weight| 1000g(transmitter + receiver)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>