STAR POWER AS01 Treadmill User Manual

STAR POWER
TREADMILL FOR HOME
AS01 Treadmill USER’S MANUAL
（V2.0）

AS01 Treadmill

Enjoy your new electrical treadmill!
Thank you for choosing our electrical treadmill made in China for your family!
This treadmill helps improve your overall health and fitness. The more familiar you are with the treadmill, the easier it will be for you to use it. We remind you to read the User Manual thoroughly before using the treadmill. Assembled with high-performance parts made of quality materials, the treadmill has undergone strict inspection and testing, which ensures it meets your expectations to the greatest extent. The Manual helps you get through the assembly process. It also provides tips on how to properly use and maintain the treadmill. Thank you again for choosing us!

CAUTION
Please read the manual carefully before using the treadmill. Keep the manual properly.

Safety Instructions

The treadmill is designed and manufactured taking your safety as the top priority. For your safety, please read through the Manual before operating the treadmill. We shall not be held responsible for any consequences caused by improper operations.

Danger:
Do not use a heart rate testing device or any other wireless heart rate device at the same time. It may cause electrical interference to the treadmill.
Please follow the instructions below to avoid harm or injuries to you or other people.
Warning:

1. Before using the treadmill, make sure it is properly grounded to avoid any accidents or dangers.

2. While using the treadmill, attach the safety lock (red) and clip your cloth properly so that in case of emergency, the safety lock can be pulled off immediately to stop the treadmill for your safety.

3. （1）. Consult your healthcare provider before exercising.
   （2）. Wear suitable workout clothes for exercise (no running with soft-soled shoes, as the soft soles, might get drawn into the motor and control system, causing the treadmill to malfunction).
   (3). Keep the room clean and tidy to avoid clumps being brought into the treadmill by electrostatic adsorption, resulting in malfunction of the treadmill.
   (4). The maximum weight capacity of the treadmill is 300lbs.

4. The treadmill is designed for the use of one person. When the treadmill is operating, keep away little children or pets to avoid any accidents.

5. The minimum distance (between the treadmill and walls and furniture) required for the treadmill when it is fully unfolded should be no less than 3fts at the front, left and right sides and 6fts at the rear side.

6.  Do not use the treadmill if the power cord is damaged.

7. Do not use the treadmill if the treadmill is damaged or broken. Contact your local distributor for repair immediately.

8. Do not touch any moving parts with your hands. Do not press against or stuff any objects into the treadmill.

9. The treadmill is for indoor use only. Avoid using it outdoors or in a gym.

10. Place the treadmill on clean and flat ground, keep the treadmill well ventilated, make sure there’s no sharp object nearby, and do not use the treadmill near water and heat sources.

11. Use the handrail when getting on and off the treadmill. Do not get off before the treadmill stops completely. For any emergency when you need to jump off, remove the safety lock to stop the treadmill immediately.

12. Do not use the treadmill while using respiratory equipment or sprays near the treadmill.

13. In order to maintain the proper operation of the treadmill, do not install or attach any accessories or parts that are not provided by the manufacturer of the treadmill.

14. All parts of the treadmill must be properly and firmly assembled.

15. Turn off the power and unplug the treadmill immediately after using it.

Packing Details

Packing Details

Accessories

Assembly

Step 1

Take the main frame, electronic panel, phone stand, and smart bracelet out of the carton, and open the cable ties binding the frames (note: the foot pad is adjustable).

Step 2

unfolding the frame: follow the demonstration below, hold the column with your hands and pull it up slowly in the direction of the arrows, and use B# (T-shaped Allen Key  Wretch) to fasten the bolts in the main frame in the direction of the arrows (clockwise).
“LETTER B it will be a T-shaped Allen Key Wretch”
After the finding part, you must fasten the bolts on the mainframe in the same direction as the blue arrows are shown. (In the example image shown to the right turn Clock-Wise.

Step 3

Rotate the armrest in the direction of the arrows to the corresponding position of the column (as shown in Figure 1); Connect the 4-core wire in 2# (electronic panel) and the  4-core wire in the column (as shown in Figure 2); push the electronic panel horizontally in the direction of the arrow, clamp and fix it on the column with D# (8*16, hex socket head bolts) and E# (flat washer); and insert 3# (Phone Stand) into 2# (electronic panel) (as shown in Figure 2), and then paste F# (mobile phone silicone sticker) onto it.

Step 4

Product usage : when the power is on, wait till the light in the electronic panel turns on. The treadmill is ready for use with a single press of the START button!
(Note: The safety lock must be placed on the yellow sticker in the middle under the meters to start the treadmill. If the electronic panel displays “SAFE”, it means the safety lock is not placed or not in the right position.)
Emergency stop: After the safety lock is pulled off, the power supply is disconnected, but the weak current remains.
The operation is not controlled by the software associated with the treadmill. For your safety: When exercising, be sure to use the safety lock!
Note: Upon confirming, the assembly is completed strictly following the above-mentioned requirements, lock all the screws and double-check to ensure there is nothing missing before turning on the power.

Step 5

Folding: fold the treadmill as shown in the figure below if it is not used for a long time. First, loosen the special bolt in the column with a T-shaped Hex Allen Wrench in the direction of the arrows and unplug the power cord (5) in the direction of the arrow, place the column back to the mainframe in the direction of the arrow, hold the rear end of the treadmill with your hands, lift the treadmill slowly in the direction of the arrow, and lean it against a wall.
Unfolding: lay the treadmill flat on the floor as shown in the figure below, lift the column slowly in the direction of the arrow, and use the T-shaped Hex Allen Wrench to tighten the special bolt in the column in the direction of the arrow, and plug the power cord (5).

Electric Control

Using The Treadmill

1. Plug on the treadmill and turn on the switch (red).
   (1) Wait for the screen to light up and enter the start interface.

2. Safety lock
   (1). Put the safety lock in the designated area on the electronic panel to start the treadmill; attach the safety lock clip onto your clothes. In case of any emergency, pull off the safety lock to stop the motor of the treadmill immediately. To continue using the treadmill, just put the safety lock back. In any case, you can stop the treadmill by pulling off the safety lock.

3. System Operation
   01. Time Display：
   (1). Display running time as (mm: ss) for the time range (0-99:59) and (hh: mm) for the time range longer than 100 minutes.
   (2). Display the error code when any malfunction occurs.
   02. Distance Display:
   (1). Display the distance of movement in miles with the precision of 0.001 miles.
   03. Calorie Display：
   (1). Display the calories consumed in kcal with the precision of 0.01 kcal.
   04. Speed Display：
   (1).Display the running speed in mile/hour (mile/h) with the precision to 0.1 mile/h.
   (2). Once operation starts, the display switches every 5s.

4. Keys and Functions
   01. Start/Pause button:
   In the standby state of the treadmill, press the Start button to activate the treadmill, and press the button again to start the treadmill. In the operating state of the treadmill,  press the Start button to pause the treadmill while keeping the existing data of the exercises, and press the button again to continue exercising.
   02. Stop Button:
   In the operating state of the treadmill, press the Stop button to stop the treadmill and clear out the data of exercises.
   03. Speed Increase and Speed Decrease buttons:
   • In the operating state of the treadmill, there are three interactions with the Speed Increase and Speed Decrease buttons.
   (1). Short press the button in 1 second to increase/decrease the speed by 1.0 mile/h each time;
   (2). Long press and hold the button for over 1 second to increase/decrease the speed by 0.5 mile/h each time;
   (3). Quick press the button multiple times in 0.5 seconds each to change the speed by 0.5 mile/h each time. While displaying other indicators, adjusting speed will lead back to the Speed Display.
   04. Speed Shortcuts：
   Touch the Speed Shortcut key 3 to set the speed to 3.0 mile/h and key 6 to 6.0mile/h, and jump back to the Speed Display.
   05. Safety Lock:
   In any state, pulling off the safety lock will stop the operation immediately and display “SAFE” on the electronic panel.
   06. Unmanned Shutdown:
   In the operating state of the treadmill, if the treadmill detects an unmanned state for more than 10s, it will automatically stop. In the standby state, press and hold keys 3 and key 6 for more than 5 seconds to cancel the Unmanned Shutdown function till the buzzer beeps. The treadmill will automatically resume the Unmanned Shutdown function after a power cut.

5. Normal operating function
   (1). In the standby state, touch the screen to bring the screen back to the display state. Press the Start button to activate the treadmill and press the button again to start the treadmill.
   (2). In the operating state, press the Speed Increase and Speed Decrease buttons to set the desired speed.
   (3). In the operating state, press the Stop button or Power On/Off or pull off the safety lock to stop the treadmill.

Connect the mobile app

Treadmill supports connection to mobile phone via Bluetooth

1. Download the PitPat app on your phone and install it Search for “PitPat” in the app store or scan the following QR code to download and install the app.

2. Configure PitPat app account Open the PitPatt app and follow the app instructions to log in or register account information

3. Connect the treadmill
   (1) Turn on the Bluetooth function of the mobile phone (the android mobile phone also needs to turn on the positioning function)
   (2) Open the PitPat app (if the app prompts for authorization, please grant the app-related permissions)
   (3) Enter the app home page, click the treadmill icon in the upper left corner of the home page to enter the search interface, and your phone will automatically search for nearby devices. Tap your treadmill (devices starting with PitPat-T are your treadmills) to connect. After the treadmill makes a beep, the connection is successful, and the  Bluetooth icon on the treadmill panel lights up.
   Note: Please make sure your phone is connected to the Internet when connecting the treadmill via Bluetooth

4. Treadmill WIFI network configuration
   After the treadmill is successfully connected to the mobile app, it will enter the treadmill WIFI configuration interface.
   Note: The treadmill only supports 2.4GHZ WIFI (the app also only displays the 2.4GHZ WIFI signal that the treadmill can search for), please make sure that your network device can provide a 2.4GHZ WIFI signal
   (1) Find the network you need to connect to
   (2) Enter your WIFI password according to the prompt. After the treadmill successfully connects to the network, the WIFI icon on the treadmill panel lights up and the app will return to the home page.
   Note: If the WIFI connection fails, after the WIFI returns to normal, please restart the treadmill so that it can reconnect to the Internet

5. Connect the bracelet to the treadmill
   Turn on the treadmill, put the screen of the bracelet on the NFC logo of the treadmill, the treadmill makes a sound of “bleep”, and the bracelet is connected with the treadmill.
   Once the bracelet is successfully bound, it will record your running information immediately.

Maintenance

Proper maintenance helps keep the treadmill in the best condition while improper maintenance may damage or shorten the life span of the treadmill.
Warning:   Before cleaning  or performing the maintenance of the treadmill, make sure to turn off and unplug the

1. Deduct the treadmill on a regular basis to keep the parts clean.
2. After using the treadmill each time, wipe the meters and other parts with a clean towel or cloth to remove the sweat and debris. Be careful to keep the electrical components and running belts away from water.
3. Keep the treadmill in a clean and dry environment and make sure the power is off and the treadmill is unplugged.
4. To facilitate the moving of the treadmill, it is equipped with wheels. Before moving the treadmill, make sure to disconnect the power supply and fold the treadmill properly.
5. Check all parts of the treadmill frequently and lock them properly, and replace the damaged part immediately if any.
6. To better maintain and extend the life span of the treadmill, it is highly recommended to limit the exercise to 30 minutes each time and let the treadmill cool down for 10 minutes before restarting.
7. The running belt has been properly adjusted at the ex-work stage, but after using, the running belt may be stretched more or less, which may cause damage to the belt due to its deviation from the center and rubbing against the sidebars and the rear cover. It is common to see the running belt stretched after using it for a while. If the running belt becomes slippery or stuck when using the treadmill, you may adjust the tightness of the running belt to improve the condition.

A. Belt adjustment.

If the running belt becomes too loose, insert the hex Allen Wrench provided with the treadmill into the adjustment hole at the left foot guard of the treadmill, turn it by 1/4 of the cycle clockwise, and repeat the same process with the right foot guard. Keep in mind to adjust both sides synchronously to tighten the belt while avoiding its deviation from the center. If the running belt is too tight, adjust both sides synchronously counterclockwise.
Note: The running belt cannot be too tight, which may cause damage to the running belt or the roller bearings due to increased pressure on the front/rear rollers, or result in abnormal noises or other problems. Adjust the running belt to the appropriate tightness only to make sure there’s no slipping.

B.Running Belt Off-Center Adjustment
While using the treadmill, the pressure on the running belt is not balanced because the acting force from the left and right feet is not exactly the same while running, which could easily cause the running belt to become off centered. That’s a normal deviation. It will return to the center automatically when nobody is using the treadmill. Otherwise,  you may need to bring the running belt back to the center.

Operate the treadmill without anyone on it, adjust the speed to level 6, and observe the distance between the left and right sidebars.

• If it is too close to the left side, use a hex Allen wrench to turn the left screw 1/4 of the cycle clockwise;
• If it is too close to the right side, use a hex Allen wrench to turn the right screw 1/4 of the cycle clockwise;
• If the belt is still not well centered, repeat the above adjustments until it comes back to the center.
• After adjusting the running belt to the center, set the speed to level 6 and observe if there’s any deviation of the running belt from the center or any slipping of the running belt. If the deviation persists, repeat the above steps to further adjust.
  Warning! Do not overtighten the rollers! It may cause permanent damage to the bearing!

Lubricant

The treadmill is lubricated before it leaves the plant, but frequent inspection of the lubrication status of the treadmill helps keep the treadmill in its best condition. The treadmill must be lubricated after one year of use or 100 hours of operation.
After using for 30 hours or 30 days, whichever comes first, while the treadmill is stationed, lift the running belt from one side and reach out to the surface underneath the running belt to decide the lubrication status. You do not need to add more lubricant if you can touch the lubricant. But if it’s dried up, follow the instructions below to refill the lubricant. (Please only use non- petroleum-based lubricant)
Follow the figure below to properly add the lubricant. Open the refilling cover on the left front side of the sidebar, use scissors or a utility knife to cut the lubricant bottle at the position shown in the figure below, and add the lubricant according to the figure at the bottom. Insert the thin rod at the front end of the lubricant bottle into the filling port on the running board and fill in the lubricant.

General Troubleshooting

Error codes displayed on the electronic panel and related troubleshooting solutions

for loose, disconnected, or damaged communication cables.
(2). Check or replace the electronic panel if needed.
(3). Check or replace the controller if needed.
Er 3| Overvoltage| (1). Check whether the voltage of the power supply is at a normal level of AC 110V.
(2). Check or replace the controller.
(3). Check or replace the motor.

Er 4

| ****

Overcurrent

| (1). Check for overload status.
(2). Check if any mechanical moving part is stuck.
(3). Check the level of the film release agent. The lack of a film release agent may increase the friction between the running belt and the running board, which causes overcurrent.
(4). Check the running board for severe wear.
(5). Check the running belt for severe wear.
(6). Check if any short circuit exists in the motor line.
(7). Check or replace the controller.
(8). Check or replace the motor.
Error Code| Error Description| Troubleshooting Solutions
---|---|---

Er 5

| ****

overload

| (1). Check for overload.
(2). Check if any mechanical moving part is stuck.
(3). Check the level of the film release agent. The lack of a film release agent may increase the friction between the running belt and the running board, which causes overcurrent.
(4). Check the running board for severe wear.
(5). Check the running belt for severe wear.
(6). Check if any short circuit exists in the motor line.
(7). Check or replace the controller.
(8). Check or replace the motor.
Er 6| The motor is not connected| (1). Check for loose or disconnected lines for the motor.
(2). Check or replace the controller.
(3). Assess the need to replace the controller.
Er 7| Communication failure, the controller cannot receive signals| (1). Check for loose, disconnected, or damaged communication cables.
(2). Check or replace the electronic panel.
(3). Check or replace the controller.
Er 13| IGBT Short Circuit| (1). Check if the treadmill is subject to strong interfering signals.
(2). Check or replace the controller.
Er 14| Load Short Circuit| (1). Check if there is any foreign object at the output of the controller that causes a short circuit.
(2). Check or replace the motor.

FAQs and Troubleshooting

and test if the keys are functioning.
2. Check or replace the electronic panel
3. Check if the keys function well upon resumption.
Thehealsencotrodnisipclpaay. nel| 1. Check if the input voltage is within the functional range.
2. Check if the switch on the treadmill is turned on.
3. Check if the fuse in the power socket is broken. If yes, replace it with a spare fuse.
4. Check if the LED light of the controller is on.
5. Check the connecting lines.
6. Check or replace the electronic panel.
7. Check or replace the lower control circuit board.
Other problems| Troubleshooting
---|---
The treadmill won’t start.| Cehmecokveifdt. the power is plugged on properly, the Power On/Off is turned on or and the safety lock is
Treadmill slips.| Refer to the Manual to adjust the tension of the running belt.
Running belt goes deviation.| Refer to the Manual to adjust the running belt to the center.
Abnormal noises| Check if any screw is loose and if the running belt needs lubrication.

Warranty Terms

Warranty scope
Non-artificial damage occurring during normal use and proper maintenance of the treadmill excludes the following conditions.

a.Damage caused by abuse, negligence, accident, or unauthorized modification;
b.Damage caused by improper adjustment of the running belt and drive belt;
c.Damage caused by improper maintenance; or
d.Damage caused by other improper operations.

The warranty is valid only for private use at home. It does not apply to professional training in the gym or other circumstances.

Notes for Exercises

• Consult your doctor before starting exercises or training programs, and follow your doctor’s advice and instructions.
• Consult your doctor to set goals for exercises, make sure your plan is realistic and start your training program in no rush.
• You may add some cardio workouts to your training programs, such as walking, jogging, swimming, dancing, and cycling. Check your pulse frequently. If you do not have an electronic heartbeat monitor, consult your doctor for a correct way to measure your pulse by hand from your wrist or neck. In addition, you must set a target heart rate based on the limitation of your age and physical conditions.
• Drink plenty of water during the workout. You must replenish enough fluids through intensive exercises to avoid dehydration. Avoid drinking large quantities of ice water or beverages. It’s best to have the drinks at room temperature.

Warm-up Exercises

Warm-up and Relaxation
A successful training program includes a warm-up, cardio, and relaxation. It’s recommended to exercise at least two or three times weekly, having one-day off after one day of exercise. After a few months, you may exercise four to five days a week.
Warm-up is a crucial part of your workout and you should always warm up your body before exercising. A moderate warm-up helps prepare your body for more intense exercises, because it gently stretches your muscles and releases the tension in them, improves blood circulation, raises the pace of your pulse, and sends more oxygen to your muscles. After cardio exercises, repeated warm- up exercises can help reduce your muscle soreness. We recommend the following warm-up and soothing exercises.

FCC

FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
• Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF Exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Warm-up Exercises

1 . Stretch down:
Bend your knees slightly with your body stretched down slowly, let your back and shoulders relax, and try to extend your hands to touch your toes. Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times.

2. Hamstring stretch:
Sit down on a clean cushion, straighten one leg and place the other leg inward towards the thigh, and snug on the inside of the straightened leg. In the meantime, try to touch the toes of your straitened leg with the hand on the same side. Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times for each leg.
3. Calf and Achilles Tendon Stretches:
Place both hands against the wall while standing with one foot behind the other, keeping your back leg straight and both heels planted on the ground while leaning against the wall. Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times for each leg.
4. Quadriceps Stretch:
Hold your body steady with your left hand holding against the wall and your right hand reaching back to grab your right heel and pull it slowly towards your hips until you feel the muscle tightness at the front side of your thigh. Hold for 10-15 seconds and take a break for a few seconds. Repeat several times for each leg.
5. Sartorius (muscle of inner thigh) Stretch:
Sit on the floor with your two feet holding against each other and your knees pointing in the opposite directions, grab your feet with your hands and pull them toward your groin. Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times.

WhatsApp: 858-258-3839
Email: support@starpowergym.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>