HiFuture ColorBuds2 TWS Earbuds User Manual
- June 15, 2024
- HiFuture
Table of Contents
ColorBuds2
TWS Earbuds
User Manual
Copyright HiFuture. All rights reserved.
HiFuture, the HiFuture logo and other HiFuture marks are all owned and
registered by SHENZHEN FUTURE ACCESS TECHNOLOGY CO., LIMITED. All other
trademarks are the property of their respective owners.
The information contained here is subject to change without prior notice.
PACKAGE LIST
Please
refrain from using any damaged components.
Contact your local authorised HiFuture distributor/customer service.
DEVICE OVERVIEW
- Tap area
- Earbuds indicator light
- Microphone
- Charging interface
- TYPE C Charging port
- Earbuds case indicator light
TAP CONTROL
Play/Pause| 
|
Press one time(L/R)
---|---|---
Previous/Next track| | Press and hold for 2 second (L/R)
Volume down/up| | Press 2 times(L/R)
Activate Siri/other voice control software| | Press 3 times(L/R)
Answer/End a call| | Press one time(L/R)
Reject a call|
| Press and hold for 2 second(L/R)
Factroy Reset| | Press 5 time(L/R)
CONNECT THE EARBUDS
- Power on the earbuds and turn on the Bluetooth in your phone.
- Tap “HiFutue ColorBuds2” form the smartphone’s Bluetooh menu. There’ s a voice prompt “You are Connect to HiFture” after succeed connection with smartphone.
HOW TO RESET THE EARBUDS
If your earbuds stop syncing with each other, please follow below steps to reset the earbuds:
- Make sure the earbuds were disconnected with phone or other Bluetooth devices.
- QUICKLY TAP L & R earbud 5 times, there will be a prompt sound, which means the earbuds had been reset successfully.
- The earbuds will sync together and enter the pairing mode automatically.
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, SHENZHEN FUTURE ACCESS TECHNOLOGY CO., LIMITED declares that the radio
equipment type HiFuture earbuds. mentioned in this manual is in compliance
with Directive 2014/53/EU.
Manufacturer: SHENZHEN FUTURE ACCESS TECHNOLOGY CO., LIMITED Address: B-206,
Block B, Tsinghua Unis Inforport, Hi-Tech Park(North), Nanshan District,
Shenzhen, China.
eVatmaster Consulting GmbH Bettinastr. 30 60325 Frankfurt am Main,Germany
contact(devatmaster.com
OST_EU_20220713000004
HUA TENG LIMITED 3 Glass Street, Hanley, Stoke On Trent,ST1 2ET United Kingdom
IMPORTANT NOTES
- Before using the ColorBuds2 wireless earbuds, please charge both the case and earbuds.
- If both earbuds don’t sync together, please reset the earbuds.
- If the earbuds don’t charge, please clean the charging slot on the case and the contact surface on the earbuds.
POWER ON
Automatically
Ensure both buds are inside the charing case and take out both buds. The buds’
indicator will flash for a while, which means earbuds were Power On.
Manually
Quick Tap L& R 1~2 times until indicators light up to Power ON.
POWER OFF
Automatically
Both buds will be AUTO OFF after into case around 5 Seconds or disconnected
with smartphone over 5 minutes. Manually
Long Tap L or R earbud for 5 seconds until indicator flashes 3 times and Power
OFF.
Note: When the charging case is at low battery or out of power, the
earbuds will not automatically power on/off, please turn them on/off manually.
WEARING
- Put the earbuds into your ears.
- Rotate the earplugs to adjust the comfortable Angle
CHARGING
Please fully charge the ColorBuds2 after unboxing. Use Type-C cable to charge the charging case.
INDICATORS’ DESCRIPTIONS
-
Earbuds
Power on| Power off| Pairing| Connect| Battery Low| Fully Charge
---|---|---|---|---|---
LED flashes white once time| LED flashes white auickly one time| LED flashes white quickly| LED flashes white once per second| Battery low waning 2mins per time and LED flashes white quickly| LED always ON white -
Without charging cable
Battery low| When put earbuds into the case and charging
---|---
LED Flashes white 4 seconds| LED flashes white once -
Charging by external TYPE-C cable
Charging| Fully Charge
---|---
LED Flashes red and white one time then LED flashes red| LED atways ON red
FCC regulatory conformance:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to tadio
communications. However, there is no guarantee that interference will not
occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
FCC 1D:2BA4V-HIFUTUREHECLB
For more information, please visit:
www.hifuturegroup.com
For any assistance, email us:
[email protected]
Designed in USA, Assembled in China Made by ShenZhen Future Access Technology
Co.,Limited