ARPELLA AM7036 Series Miramar Lighted Mirror Instruction Manual
- June 15, 2024
- ARPELLA
Table of Contents
INSTALLATION INSTRUCTIONS
LEDWSM2430/LEDWSM2436/LEDWSM3436/LEDWSM4836/LEDWSM6036/LEDWSM7036
AM7036 Series Miramar Lighted Mirror
Please Read Before Installation
Please read these instructions carefully before starting installation and keep
in a safe place for future reference.
It is recommended to use a qualified electrician for all electrical wiring
procedures.
Please turn off all power to site prior to installation.
Check the contents of the package carefully before installation and disposal
of packaging.
Mirror must be wired directly to a dimmable wall switch to operate the dimming
feature on the mirror.
Mechanical switch located on the bottom of the mirror must remain on when
operating the mirror with the wall switch.
The defogging feature will deactivate when the mirror is dimmed.
Electrical information of LED Mirror
Item Code| Product
Size(inch)| Input
Voltage| Electric Power
of Mirror(Watt)| Lumens| Colour temperature
(Kelvin)| Life expectancy
of LED Strip(Hour)
LEDWSM2430| 24 Wx30 H| 110V| 50W| 2060| 5000K| 50,000
LEDWSM2436| 24 Wx36 H| 110V| 60W| 2370| 5000K| 50,000
LEDWSM3436| 34 Wx36 H| 110V| 90W| 2880| 5000K| 50,000
LEDWSM4836| 48 Wx36 H| 110V| 129W| 3590| 5000K| 50,000
LEDWSM6036| 60 Wx36 H| 110V| 166W| 4200| 5000K| 50,000
LEDWSM7036| 70 Wx36 H| 110V| 190W| 4700| 5000K| 50,000
IMPORTANT SAFETY INSTRUCTION
When using an electrical furnishing, basic precautions should always be
followed, including the following:
Read all instructions before using this product.
DANGER – To reduce the risk of electric shock:
-
Always suspend power to mirror before servicing the item if service isneeded.
-
Close supervision is necessary when this mirror is used by, or near children, invalids, or disabled persons.
-
Use this furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by Arpella. -
Never operate this furnishing if it has a damaged cord or plug, if it is not working properly during testing, if it has been dropped or damaged, or exposed to water.
-
Keep the cord away from heated surfaces.
-
Never drop or insert any object into any opening in the electrical box.
-
This product is not intended for use outdoors.
-
To disconnect, turn all controls to the off position, then suspend power to the mirror.
″WARNING: Risk of Electric Shock – Connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
INSTALLATION INSTRUCTIONS
Installation procedure
-
Before your installation, make sure the location of the mirror is suitable, ensuring that the domestic main power supply is within reach of the electrical entry point of the mirror. Mounting bracket must be attached to wall stud. Measure the distance A and drill holes in the marked positions by using a suitable tool.
-
Insert the wall plugs on the surface of the wall. After that, fasten the supplied screws in to wall plugs. Attach the mounting bracket to the wall.
-
You must have a Junction box in the wall.
Carefully connect the Hard Wire to the mirror fixture wires. Please ensure the main electrical supply has been powered off to complete installaion.
Wiring from light fitting:
House Wire Black(Live/Hot) to Fixture Wire Black
House Wire White (Neutral) to Fixture Wire White
House Wire Green (Ground) to Fixture Wire Green
The input voltage required is 110V -
Hang the mirror on the bracket, peel off protective film and clean the mirror with a soft, drynon abrasive cloth. After that, turn on the domestic electrical main power supply for the mirror light.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>