Anlapus C106 Series Security Camera Day Night Instruction Manual

Anlapus C106 Series Security Camera Day Night

Product Information

Specifications:

• Model: Z19.5.T.2
• Day/Night functionality
• Infrared LEDs for night vision
• IR Cut Filter for a clear color image in a well-lit environment

Introduction:
Thank you for purchasing the CCTV camera from Anlapus. This camera is designed to operate in various light conditions, from bright daylight to pitch darkness. It is highly sensitive to light and can capture images even in low light conditions, resulting in black-and-white images. In total darkness or near-total darkness, the camera utilizes built-in infrared LEDs to illuminate the area in front of it. The infrared light is invisible to the human eye, but a faint red glow may be noticed, which is normal.

The camera also features an IR Cut Filter that blocks out unnecessary light and provides a clear color image in well-lit environments. It is important to note that users must comply with all applicable laws and regulations regarding the use of cameras. Before using the camera, familiarize yourself with the laws and regulations in your area.

Important Safety Instructions:

1. Ensure proper installation and stable fastening of the product.
2. Avoid operating the camera if wires and terminals are exposed.

Choosing a Location for this Camera:

To mount the camera:

1. Place the camera in the desired location and mark screw holes on its surface.
2. If mounting on a wooden surface, screw the camera directly to the surface.
3. If mounting on a masonry surface, use the included wall plugs.

Mounting the Camera:

To mount the camera, follow these steps:

1. Ensure the camera is securely fastened into place using the appropriate screws or mounting hardware.
2. Position the cables properly to avoid winding them around sharp objects.
3. Avoid placing the cables close to live electrical wiring to prevent interference with the camera’s signal.
4. All wiring and connectors must be insulated and protected from moisture and sunlight as they are not weather-resistant.

Camera Lens:
Refer to the diagram for instructions on adjusting the camera lens:

1. Loosen the screw using a screwdriver and rotate the camera.
2. Loosen the screw and adjust the elbow joint.
3. Attach the neck of the stand to the mounting base and rotate the stand by loosening the radial joint locking ring.
4. Once in position, tighten the ring to secure the stand.

Frequently Asked Questions:

1. Can this camera be used in complete darkness?
   Yes, this camera has built-in infrared LEDs that provide night vision capabilities in total darkness or near-total darkness environments.

2. Is the infrared light visible to the human eye?
   No, the infrared light emitted by the camera is invisible to the human eye. However, a faint red glow may be noticed, which is normal.

3. Can I mount the camera on a metal surface?
   Yes, you can mount the camera onto a metal surface, but you will need to provide your mounting hardware.

4. Should I be aware of any laws or regulations regarding the use of this camera?
   Yes, it is the buyer’s responsibility to be aware of and comply with all applicable laws and regulations regarding the use of cameras.

Introduction

Thank you for purchasing this CCTV camera from Anlapus. This camera can operate in almost all light conditions, from bright daylight (provided it’s not irradiated directly by the sun) to pitch darkness. The camera is very sensitive to light and therefore can make use of even a tiny little of light to create an image of what it captured. When it is in low light, this comes out as a black-and-white image. In a total darkness or near-total darkness environment, the camera uses built-in infrared LEDs to illuminate the area in front of it. This light is invisible to the human eye, although you might notice a faint red glow coming from the front of the camera, which is a normal phenomenon. In a day or well-lit environment, the IR Cut Filter feature of the camera can filter out wavelengths of light that are useless to cameras to provide a clear color image.

Important note:
All jurisdictions have specific laws and regulations relating to the use of cameras. Before using any camera for any purpose, it is the buyer’s responsibility to be aware of all applicable laws and regulations that prohibit or limit the use of cameras. Also, buyers must comply with the applicable laws and regulations.

Warning:
Modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Important safety instructions

1. Make sure the product is installed correctly and fastened stably.
2. Do not operate it if wires and terminals are exposed.

Choosing a Location for this Camera

To get optimal effects from the camera, where you install cameras is pivotal. You should consider the distance between the camera and its subject to ensure you obtain a good view of the areas in focus. Also think about the appropriate mounting places (e.g., under the eaves of a roof is a good choice) where it won’t be either an easy target for vandals or affected by constant light reflections of moving vehicles (which can cause falsely triggered motion detection). There are numerous factors you should consider when choosing a location to mount your camera, not merely where you want to monitor it.

To mount the camera

• Place the camera in the location where you want to mount it, and mark screw holes on its surface to fix the screws. Then, use proper screws for the surface where you prepare to fix the camera. Screw the camera stably into the place.
• If you’re going to mount the camera on a wooden surface, then screw the camera directly to the surface. If you’re going to mount the camera on a masonry surface (bricks, concrete, or similar), then you’ll need to use the included wall plugs.

Mounting the Camera

The camera can be mounted onto a flat, vertical surface using screws. The surface must have sufficient strength to hold the camera. Materials such as hardwood, brick, or masonry are good options. You can mount the camera onto a metal surface, but you’ll need to supply your mounting hardware.

Position the Cables

1. When setting your cable, try to avoid winding it on objects with sharp angles.
2. Don’t put your cable close to live electrical wiring. AC electricity will generate radio “noise”, which can interfere with the camera’s signal.
3. All wiring and connectors must be insulated in suitably. Meanwhile, they also should be protected from moisture and sunlight because they are not weather resistant.

Please note, that the model shown is for illustration purposes only.

Mounting the Camera

1. Using a screwdriver to loosen the screw, and then rotate the camera.
2. Loosen the screw, and then adjust the elbow joint.
3. Attach the neck of the stand with the mounting base, and then rotate the stand by loosening the radial joint locking ring. Once stand in position, tighten the ring again.

Connection Guide

Please note, the model shown is for illustration purposes only.

Troubleshooting

Q: Video Loss display on my monitor where is supposed to display the image?

A:

1. Check whether the extension cable (power and video) is securely connected to the camera.
2. Check whether the video output from the camera is securely connected to the video input channel on the DVR.
3. Check whether the power from the camera is firmly connected to the power supply.

Limited Warranty Terms & Conditions

Anlapus Communications warrants this product against defects in workmanship, and all material will be warrantied for one year from its original purchase date. You must present your receipt as proof of purchase date for warranty validation. Any unit that proves defective during the stated period will be repaired without charge for components or labor. Replaced at the sole discretion of Anlapus. The end user is responsible for all freight charges when it is necessary to send the product to Anlapus’s repair center. The end user is responsible for all shipping costs when shipping a product from any country other than the origin country.

The warranty does not cover any incidental, accidental, or consequential damages arising from the inability to use this product. End users should take responsibility for any costs associated with the fitting or removal of this product caused by a tradesman or other person. This warranty applies to the original purchaser of the product only, and it is forbidden to transfer the product to any third party. It will make all warranties voided if there are unauthorized end users or third parties modify any component misuse evidence or abuse the device.

By law, some countries do not allow limitations on certain exclusions in this warranty. Where applicable local laws, regulations, and legal rights will take precedence.

• Website: www.anlapus.com.
• E-Mail: anlapus@ansjer.com.

All rights reserved. No part of this publication may be reproduced by any means without written permission from Anlapus. The information in this publication is believed to be accurate in all respects. Anlapus cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

References

• Anlapus

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>