Kitchenwell KN315 Instant Hot Water Dispenser User Manual
- June 15, 2024
- Kitchenwell
Table of Contents
**Kitchenwell KN315 Instant Hot Water Dispenser User Manual
**
- Warnings
- Product details
- User manual
- Tips & cleaning
- Troubleshooting
Warnings
Safety precautions
- Read the instructions before use.
- Prevent the cord from coming into contact with water.
- Do not use the hot water dispenser without water in the reservoir.
- If the power cord is damaged, the hot water dispenser should no longer be used. Contact the retailer to see if repair is possible.
- Only use the hot water dispenser indoors.
- Prevent the cord from getting hot.
- Before use, check that the socket has the correct voltage.
- Do not use the blender empty.
- Keep out of reach of children.
- The hot water dispenser is made to be used under normal household conditions.
- Do not use the product with other liquids.
- Steam and water are very hot, handle this with care.
- Do not use the hot water dispenser above the max and below the min line.
- Caution: improper use may result in injury
Product details
- Control panel
- Dispenser
- Drip plate
- Drip tray
- Water tank cover
- Water tank
| | | | |
---|---|---|---|---|---
Model:| Content| Voltage:| Power:| Weight:|
Measurements:
KN315| 3L| 220/240V 50/60HZ| 2200W – 2600W| 3.2KG| 15.5 x 25.5 x 32.5 CM
- Clean the water tank before use.
- Fill the water tank with clean water.
- Fill the water tank with the desired amount. This can be done in 2 ways, by taking off the entire water tank or by taking off the lid and filling the tank from the top. Do not fill above the MAX line.
- Now connect the hot water dispenser to the wall socket.
- Place a cup under the dispenser. Select the desired temperature and volume and press the ON/OFF button. To stop dispensing press ON/OFF again.
Control panel
- Press LOCK for 3/5 seconds to unlock the device. After 10 seconds, the device automatically locks again.
- Select the desired temperature: 45ºC / 55ºC / 65ºC / 75ºC / 85ºC / 100ºC.
- Choose the desired volume: 100ml / 200ml / 300ml / 400ml.
- Select MILK to disperse water at 40ºC degrees. Control panel
- Select the COFFEE/TEA function to disperse water at exactly 92ºC degrees. This makes it instantly drinkable.
- At volume 000, select to let water flow continuously. Ideal for a pot of tea.
- Press ON/OFF to start and stop dispensing.
- Lack of water notification: fill the water tank with more water
- Descaling notification: descale the hot water dispenser.
Tips
- The hot water dispenser has a reminder function, the last programmer will be remembered until the plug is removed from the socket.
- If the hot water dispenser fails or does not work properly, the built-in security function may have been activated. Easily reset the appliance with the reset key according to the illustration.
Cleaning
- Unplug the appliance and let it cool down before cleaning.
- Descale the appliance with natural agents such as vinegar or citric acid.
- Add this to the water and fill the water tank to MAX.
- Select 100ºC and 000 volume and operate 2/3 times on this setting to rinse everything thoroughly.
- Clean the outside with a slightly damp cloth.
- Empty the drip tray by gently lifting it.
- After cleaning, remove the drain plug at the bottom of the appliance to remove all water residues. Connect it properly after emptying.
Troubleshooting
| Problem | Solution |
|---|---|
| Water does not heat | Reset the appliance with the reset key. |
| Water tastes like lime | Descale the appliance according to the instructions. |
| Error: E7 | There is not enough water in the water tank. |
| The memory function does not reset. | Unplug the power cord. |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>