BUTURE BR700 Portable Car Jump Starter User Manual

BUTURE BR700 Portable Car Jump Starter User Manual

Important Safety Warning

ATTENTION: Please read the following safety waming before using the product and take safety protection measures to avoid malfunctions caused by accidental operation.

Personal Safety

1. Store in a cool and well-ventilated place out reach of children and pets.
2. Do not place the product in high temperature environment for a long time. The operation temperature of this product is -20~60 C. The storage temperature should not exceed 50 C (122°F)

Electrical Safety

1. Only start vehicles with the smart jumper cable supplied by the manufacturer.
2. Do not use the product if the clamp or cable is damaged.
3. Do not connect the red and black clamps together when the product is outputing.
4. Do not connect the red and black clamps to the same piece of metal.
5. Do not use this product to start an expanded car battery.
6. Do not disassemble or modify this product.
7. Do not use detergent to clean this product.
8. Do   not abuse this product and avoid heavy dropping or repeatedly hitting it.

Battery Safety

1. Do not litter the product and it should be safely recycled.
2. Do not incinerate the product or exposed to high temperatures, as they may explode.
3. Only use replacement parts or accessories provided or recommended by manufacturer.

Package Content

• BR700 Jump Starter & Air Compressor

• Smart Clamps

• EC-5 Cigarette Lighter Adapter

• Charging Cable

• Valve Adapter x 3

• User Manual

• Storage Box

Know Your Product

device
6| M Button| Switch air pressure units and pump modes
7| LED Light| Illumination and emergency signals light
8| Air Hose| Connect to car tires, basketballs, etc.
9| Output 1| Quickly charge your phone, tablet, camera, etc. 75% faster than a standard charge
10| Input| Recharge the jump starter
11| Output 2| Quickly charge your phone, tablet, camera, etc.
12| EC5 Output Port| Insert the clamp plug into this port completely
13| DC Output| Connect to DC cigarette lighter to power autodevices
14| | Insert it into the ECS Output Port completely
15| Clamp Plug| Show the work status of starting vehicles
16| Clamp Indicator| Manual override when a battery is too low to be detected
17| Force Start Button| Connect to the positive terminal of the car battery
18| Red Clamp| Connect to the negative terminal of the car battery

Technical Specifications

Operation Guide

Recharging

Before use, please note

• Charger not included, a universal USB charger is fine, such as your phone charger (2A above is suggested).
• When using the product for the first time, please make sure it is fully charged
• It is recommended to charge up the product every 3 months to prolong its lifespan even if the unit has not been used.

Step 1. Connect the product to power supply via the charging cable.
Step 2. Disconnect the power after it is fully charged.

Charging USB Devices

Step 1. Connect the product to your iPhone, smart phone or other USB electronic devices via the charging cable.
Step 2. Disconnect when charging is not required.

LED Emergency Light

Long press the LED Button for 3 seconds, the white flashlight will be on. Short press to switch to SOS, red flashlight and flashing red flashlight mode in turn. Then long press to turn it off.

Starting Vehicles

Before use, please note

• This product is only suitable for 12V vehicles (all gas or up to 8.0L diesel engines).
• Before starting your car, it’s best to make sure the product has ≥50% power.
• If the Clamp Indicator isn’t flashing as described, go to the Troubleshooting (page 12).

Step 1. Insert the Clamp Plug completely into the product, the red and green indicators will flash alternately.

Step 2. Connect the Red Clamp to the positive electrode (+) of your vehicle battery and the Black Clamp to negative one (-, the red and green indicators will continue to flash alternately.

Step 3. Start your vehicle.

1. Start Directly: If the engine is not successfully started on the first try, disconnect it from the car battery to wait for at least 20 seconds. and then try again.
   

2. Manual Override (Optional): If three attempts fail, please use the Manual Override to force the vehicle to start. Make sure that the product is correctly connected, then press the Force Start Button for 3 seconds. When the indicator is green, please start the vehicle within 30 seconds.
   Warning: When using the Manual Override Function, auto-detection and safety features will be disabled.
   

3. Step 4. When the vehicle is started, remove the jumper cables from your car battery and the jump starter within 30 seconds.
   

Inflating Tires

Before use, make sure that

• Only use on tires and inflatable items.
• This product isn’t a substitute for a Tire Pressure Monitoring System tool.
• The valve and the air hose are not damaged before each inflates.
• Do not bend or restrict the air hose while the compressor is in use.
• Choose the free mode carefully as setting too high an air pressure may risk a tire blowout.
• Refer to your vehicle manuals for the correct tire pressure required before you set your desired pressure. The standard tire pressure is usually displayed in the vehicle user manual, the label next to the cab door (near the B pillar), the drawer next to the driver’s seat, the fuel door, etc.
• Take extra care not to over-inflate when inflating other inflatable items such as sports ball, bike tires, air bed, etc.
• The high temperature will pressurize the tire, so please inflate when the tire cools.
• Avoid using in rainy or wet conditions as water entering the unit can cause internal damage and premature failure.
• In case of an electrical or mechanical fault, immediately switch off and unplug the compressor.
• To extend the service life, do not inflate for more than 8 minutes at any one time. If using for extended periods, please let the device rest for 5 minutes allowing for it to cool down.

Step 1. Short press the Power Button to activate the product.
Step 2. Set air pressure.
Short press M Button for mode switching, from default Car Mode (default 36PSI) to Motorcycle (default 34.5PSI), Bicycle (default 45PSI), Ball (default 8PSI) and Free Mode (default OPSI) in turn. Long press M Button to activate unit switching, then short press to switch from default PSI to BAR, KPA and Kg/cm² in turn. After the selected mode or unit blinks 3 times, the mode or unit is selected.

Press the +/- Button to increase/decrease the air pressure value on the LCD Display until your desired pressure is reached.

Step 3. Remove the dust cap from the tire valve and connect the Air Hose securely onto the tire valve, then press down the handle to fix the air hose. Once attached, your tire pressure will be displayed on the LCD Display.

Step 4. Press the Pump Button and start to inflate. The product will automatically shut off when it has reached the pre-set pressure. Then long press Power Button to shut the device completely, disconnect the air hose, and screw the dust cap back.

Smart Protection

Ared triangle logo will on the LCD Display for auto protection if there is any situation such as over heat,over current or short circuit.

Please shutdown and reboot to release protection.

Troubleshooting

In any of the following situations, the smart clamp turns protection on:

• Recharge the product

Red indicator| Connection timed out

• Please reconnect the clamps

Red indicator with beeps| Reconnect and check:

1. The clamps are reversely connected
   • Check whether the smart clips are connected backwards.
2. The smart clamp is short-circuited
   • Check whether the red and black clamp are connected
3. together or connected to the same piece of metal. Poor connect
   • Adjust the smart clamp to maximize connected to the car battery terminals

Flashing red indicator| Temperature of smart clamp exceeds 65±5 C –Remove the smart clamp until the indicator resumes flashing red and green alternately
Othera| Please feel free to contact us via support@ibuture.com with details of the issue

Warranty

Our company provides customers with warranty of 24 months from the date of purchase.

Contact Us

For additional assistance or warranty cover claim, please contact us via E-mail: support@ibuture.com

Federal Communication Commission Interference Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not ocur in a particular installa- tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Correct Disposal of this product

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Declaration of Conformity

We (Manufacturer is responsible for this declaration)

koo Electronic Co.Lid..
(Company name)

‘BO9.block B.f2.bldg.b.runfeng Pioneer Park.no.973. minzhi Avenue, Minzhi St. Longhua, Shenzhen. CN (Company address)

declare under our sole responsibility that the product
Trade   name: BUTURE
Equipment: Car Jump Starter
Model No. : BR700

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>