REDRAGON ZEUS X Wireless Gaming Headset Instruction Manual

Table of Contents

Dear user

Thank you for choosing product. To protect your rights and for better customer service, we ask that you note our warranty rules.

Within guaranty period, repair is guaranteed for failure due to electrical circuit problems. Other damages, such as disassembly, hard Impacts, submersion Into water, plugging into improper current or voltage, and damage caused by natural disasters such as fire, flood, or earthquake are not included.
Consumable parts (such as foot pad) and spare parts replacement are not included in our warranty.

REDRAGON-ZEUS-X-Wireless-Gaming-Headset-01

Turn ON/OFF the headset

Long press the power button for about 5 seconds to turn it on,and the blue indicator will turn on, press it again to turn off. Short press to switch the backlighting mode.

Features

Bidirectional transmission system, 48K/16bit sampling rate Unique virtual surround sounds mode, Low latency<25ms 2.4G band, and it also apply in every other country
Adaptive frequency hopping technology, Friendly coexistence with WiFi and other wireless devices Support 3.5 audio converter cable connection

How to pair

Plug the transmitter into the computer, and the light of the transmitter will continue to flash,then turn on tne headset and long press tne mlcroprlone keywltn five seconds, headset will searching the device, pairing indicator will flash quickly,the LED will be light on after pair sucessful.

The function of microphone button

Audio socket (3.5mm port)

Use the two-way single 3.5 audio converter cable, one of the 3.5 pins to connect the headphones audio socket, can be converted into a single 3.5 earphone for use.

TYPE• C socket(Charging port)

You can use type-C cable to charge your headprlones.
Type Cto USB cable function
Use USB to transfertype-C data cable, connect one headset type-C interface and one headset to the computer, and then update the headset program.

Headset indication Tone

It will have indication while turn on /off the headset(once), turn on (twice)/off(once) the microphone, low power (once in a minute).

Virtual 7.1 sound button

Smart power saving mode

1 0 minute automatic sleep without music,5 minute automatic sleep without connection.

Low power mode

When the battery power supply voltage is less than 3.35V, indication tone will beep one time every one minute. After 20 minutes, the headset will turn off.
Electrical characteristics

Standard: 2.4G

Charging Tlme :around 3h

Speaker specification

Loading Impedance: 64±15% OHMS ( F=1 KHz)
Out Sound Pressure Lever [S. P.L): 111dB±3dB At 1KHz/0.179V /1 mW
Frequency Response: 20~20KHz (at 1 KHz Output 5.P.L±10dB)
Total Harmonic Distortion: :s:5%
Drive Unit Dimensions: $53mm * 1 O mm(H)
Power Rating : Normal: lOmW; Maximum: 20mW
Buzz & Rating: Sine Wave: 0.89V (Must Be Normal)
Load Test: Normal 1 OmW 48Hours (White noise)
Magnet : (NdFeB)
Polarity : Diaphragm Shall Move Forward While Apply a Positive DC Current Tothe + Markedw Termlnal

Drive Unit Dimensions: 4>6mm * 2,7mm(H) Sensitivity:-38±3 dB (Od8=1 V/Pa.1 KHz)
DI reactivity : Om n id I recline
Output Impedance: 2.2KOHMS I
Frequency Response: 100~1 OOOOHz (at 1 KHz ±3dB)
Total Harmonlc Distortion: ?5%
Operating Voltage : DC 1.ov-1 av
Standard Operating Voltage : DC 2.0V
Current Consumption : Max O.SmA
5/N Ratio : 60dB or More
Maximum input S.P.L : 1 OOdB

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 oftne FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions

this device may not cause harmful interference ,and
this device must accept any interference received, including interference that may cause undesired operation.

California Proposition 65 , &. WARNING:

Risk of Cancer from [Name of one or more chemicals known to cause cancer] And Reproductive Harm From [Name of one or more chemicals known to cause reproductive toxicity] Exposure –www.P65Warnings.ca.gov.