DJI SS3M302110 Matrice 30 Series Dock Drone User Guide

DJI Matrice 30 Series Dock Version
User Guide
v1.0

Introduction
DJI™ MATRICE™ 30 Series Dock Version aircraft can be linked to DJI Dock Version. With DJI Flight Hub 2, it can be used to perform automated operations remotely.

In the Box

Aircraft* ×1
with microSD card inserted| Screws and Tools ×1| 1671 Propeller ×2| 1671 Propeller ×2
---|---|---|---
| | |

• The M30 Dock Version and M30T Dock Version are equipped with different cameras. Refer to the actual product purchased. This guide uses the M30T aircraft as an example.

Preparing the Aircraft

| • Make sure the propellers are securely mounted and not damaged or deformed and that there are no foreign objects in or on the motors or propellers.
• Make sure the lenses of the vision systems, gimbal cameras, FPV camera, the glass of the infrared sensors, and the auxiliary lights are clean and not blocked in any way, and the protective stickers are removed.
• Make sure the waterproof rubber port covers are correctly in place and securely sealed.
---|---

1. Unfold the frame arms on both sides in the same way. Make sure the frame arm folded buttons pop out so that the frame arms are locked firmly.
2. Make sure the gimbal camera is facing forward laterally.
3. Insert two TB30 batteries (purchased separately). Make sure the battery release toggles are in the same position as shown in the diagram.
4. Press and then press and hold the power button to power on/off the aircraft. The power indicator glows solid after the aircraft is powered on.

| • Push the battery release toggles outward to remove TB30 batteries.
• Make sure to push and hold the frame arm folding button and fold the arms in before transporting the aircraft separately.
• When transporting the unpacked dock, make sure to remove the aircraft from the dock for separate transportation.
---|---

Linking to the Dock

| • The aircraft and the dock require activation before use for the first time. An internet connection is required for the remote controller during activation.
• When the dock is connecting to the remote controller and the dock cover is opening using DJI Pilot 2, make sure to keep a safe distance from the dock cover movement mechanism to avoid injury. Press any of the emergency stop buttons on the dock to stop the dock covers from opening, if necessary.
• When the dock cover needs to be closed after the aircraft is placed in the dock, it is recommended to close the cover in the app or on Flight Hub 2. Before closing the dock covers (including manual closing), make sure to move the two blades for each motor to be at 90° with each other in order to avoid breaking the propellers when closing the dock cover.
---|---

1. Open the dock electrical cabinet door. Use the USB-C cable included in the Dock Bundle to connect the USB-C port of the remote controller to the USB-A port of the dock electrical cabinet.
2. Power on the remote controller, run DJI Pilot 2, and follow the prompts to complete the activation for the aircraft.
3. Make sure the driving rods on the landing pad are pulled back, the aircraft heading is consistent with the arrow mark on the landing pad, and the aircraft is placed on the landing pad. Move the two blades for each motor to be at 90° with each other to complete the configuration, as shown in the diagram. Make sure to close the dock cover in the app.
4. Dock Onsite Debugging in DJI Pilot 2 provides the aircraft status and operations such as charging aircraft.

Usage

Scan the QR code or go to the address to watch the tutorial videos and read the related manuals such as the Safety Guidelines, User Manual and Installation and Setup Manual. Make sure to understand the safety precautions and learn more aircraft information.

https://www.dji.com/dock/video

https://www.dji.com/dock/downloads

Disclaimer and Warning

By using this product, you signify that you have read, understand, and accept the terms and conditions of this guideline and all instructions at www.dji.com/dock.
EXCEPT AS EXPRESSLY PROVIDED IN AFTER-SALES SERVICE POLICIES AVAILABLE AT https://WWW.DJI.COM/SERVICE/POLICY, THE PRODUCT AND ALL MATERIALS AND CONTENT AVAILABLE THROUGH THE PRODUCT ARE PROVIDED “AS IS” AND ON “AS AVAILABLE BASIS” WITHOUT WARRANTY OR CONDITION OF ANY KIND. This product is not intended for children.

Specifications

5.1 GHz: < 23 dBm (FCC/CE/SRRC/MIC)
5.8 GHz: < 23 dBm (FCC/SRRC), < 14 dBm (CE)
Max Transmission Distance| 15 km (FCC), 8 km (CE/SRRC/MIC)
Power Supply| Using external battery
Compatible Battery Model| TB30 Intelligent Flight Battery

FCC Compliance Notice

Supplier’s Declaration of Conformity
Product name: Matrice 30/Matrice 30T
Model Number: M30 RTK/M30T RTK
Responsible Party: DJI Research LLC
Responsible Party Address: 435 Portage Ave, Palo Alto, CA 94306
Website: www.dji.com

We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information
The aircraft complies with FCC radiation exposure limits set forth for an uncontrolled environment.
In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (Matrice 30/Matrice 30T) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.
A copy of the EU Declaration of Conformity is available online at www.dji.com/eurocompliance
EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (Matrice 30/Matrice 30T) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.
A copy of the GB Declaration of Conformity is available online at www.dji.com/eurocompliance

Environmentally friendly disposal
**** Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the  appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

INVISIBLE LASER RADIATION
DO NOT EXPOSE USERS OF TELESCOPIC OPTICS CLASS 1M LASER PRODUCT
IEC/EN 60825-1:2014. Complies with 21 CFR
1040.10 and 1040.11 except for conformance
with IEC 60825-1 Ed. 3.,as described in Laser
Notice No. 56, dated May 8,2019
This label is affixed to one side of the Matrce 30/Matrice 30T

References

• Anatel — Agência Nacional de Telecomunicações
• DJI - Official Website
• DJI Dock - Automated drone hangars - DJI Enterprise

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>