UNTEI EC200 2 In 1 Mini Drones for Kids Remote Control Drone Instructions
- June 15, 2024
- UNTEI
Table of Contents
- EC200 2 In 1 Mini Drones for Kids Remote Control Drone
- Product Information
- Specifications
- Product Usage Instructions
- Transmitter Battery
- Charging the Drone Battery
- Operation Guide
- Pairing
- Calibrating the Gyro
- Taking-Off / Landing Method
- Q: What type of batteries should I use for the
- Q: How long does it take to charge the drone battery?
- Q: How do I know when the drone battery is fully charged?
EC200 2 In 1 Mini Drones for Kids Remote Control Drone
Product Information
Specifications
- Transmitter Battery: 3 x AAA batteries (not included)
- Drone Battery Charging: USB Adapter (5V@0.5-2.0A)
- Charging Time: about 60-70 minutes
Product Usage Instructions
Transmitter Battery
To install the transmitter battery:
-
Unscrew the battery cover.
-
Press and slide the battery cover out.
-
Insert 3 x AAA batteries (not included), making sure to follow
the correct polarity as shown. -
Re-attach the battery cover.
Charging the Drone Battery
To charge the drone battery:
-
Read the instruction of the 2.3 Use of Battery section of the
Safety Guidelines carefully before charging. -
Plug the USB charging cable into a USB charging port on the
computer, power bank, or USB adapter (5V @ 0.5 to 2.0A). -
Connect the wire of the battery with the USB charging
cable. -
The charging time is about 60-70 minutes.
-
The red indicator light on the USB charging cable will turn off
when the battery is under charging and will turn on when the
battery is fully charged.
Operation Guide
Pairing
-
Push the power switch to the right to turn on the remote
control. The remote control will make a beep, and the power
indicator will flash. -
Push the power switch of the drone to the right to turn on the
drone. The indicator light of the drone will flash rapidly. -
Place the drone on a flat and level surface with the head
forward and the tail towards the operator. -
Slowly push the left joystick of the transmitter up to the top
(the transmitter will beep once), then pull it down to the bottom
(the transmitter will beep once again). -
When the power indicator of the remote control turns solid and
the LED lights of the drone appear flickering, the pairing is
completed.
Calibrating the Gyro
After pairing, short press the gyroscope calibration button. The
remote control will make a beep, and the LED lights of the drone
will flash quickly for 2 seconds. At this point, the drone is reset
to factory settings and is ready to fly.
Taking-Off / Landing Method
Method 1: Push the left joystick up until the propellers of the
drone rotate without taking off. Then push up the left joystick
again to take it off. Pull the left joystick down until the
propellers stop rotating, and the drone will land slowly.
FAQ
Q: What type of batteries should I use for the
transmitter?
A: Always use alkaline batteries for the transmitter. Never mix
old and new batteries.
Q: How long does it take to charge the drone battery?
A: The charging time for the drone battery is about 60-70
minutes.
Q: How do I know when the drone battery is fully charged?
A: The red indicator light on the USB charging cable will turn
on when the battery is fully charged.
7.3 Transmitter Battery
Battery Cover
3 x AAA batteries (not included) Always use alkaline batteries, never mix old
and new batteries. WARNING
1. Unscrew the battery cover, press and slide the battery cover out, and
insert 3 x AAA batteries(not included), make sure to insert them following the
correct polarity as shown.
2. Re-attach the battery cover.
8.0 CHARGING
8.1 Drone Battery
USB Adapter (5V@0.5-2.0A)
Before charging, please read the instruction of the “2.3 Use of Battery” section of the “Safety Guidelines” carefully!
Power Bank
Computer USB Port
1. Plug the USB charging cable into a USB charging port on the computer,
power bank or USB adapter (5V @ 0.5 to 2.0A ).
2. Connect the wire of battery with USB charging cable. 3. Charging time:
about 60-70 minutes. 4. The red indicator light on the USB charging cable will
be off when the
battery is under charging; and will turn on when the battery is fully charged.
9
9.0 OPERATION GUIDE
9.1 Pairing
(1). Push the power switch to the right to turn on the remote control. At this
time the remote control will make a beep, and the power indicator of the
remote control will flash.
Power Switch
(2). Push the power switch of the drone to the right to turn on the drone, and
the indicator light of the drone will flash rapidly at this time.
(3). Place the drone on a flat and level surface with the head forward and the
tail towards the operator.
HEAD
(4). Slowly push the left joystick of the
transmitter up to the top ( the
transmitter will beep once); then pull it
down to the bottom ( the transmitter will
beep once again). When the power
indicator of the remote control turns
Up
solid, and the LED lights of the drone
appear “flickering”, the pairing is
Down
completed.
10
9.2 Calibrating the Gyro
After pairing, short press the gyroscope calibration button. The remote control will make a beep, and the LED lights of the drone will flash quickly for 2 seconds. At this point, the drone is reset to factory settings and is ready to fly.
Short Press
9.3 Taking-Off / Landing Method
Method 2: Push the left joystick up until the propellers of drone rotate
without taking off and then push up the left joystick again to take it off.
Pull the left joystick down until propellers stop rotating, the drone will
land slowly.
11