P I T E-PES3.6P-24A Cordless Screwdriver Instruction Manual

P I T E-PES3.6P-24A Cordless Screwdriver

PRODUCT OVERVIEW

Safety Notes

General Power Tool Safety Warnings
WARNING Read all safety warnings and all instructions.

Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.

Work area safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Ensure the switch is in the off position before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Battery tool use and care

• Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into power tools that have the switch on invites accidents.
• Recharge only with the charger specifi ed by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fi re when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fi re.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, fl ush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Product Description and Specifications Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Introduction Cordless screwdriver- designed for screwing and unscrewing of screws, bolt screws, self-tapping screws. As working nozzles indrills are used so-called bits, one end of which has the shape of a drill, and the other is made in the form of a hex shank.

Technical Data

• Model E-PES3.6P-24A
• Voltage 3.6 V
• Rotating Speed 180 r/min
• Torque 2 N·m
• Hexagon drive hole 6.35mm
• Weight 175 g

Contents of delivery

• Cordless Screwdriver 1 pc
• Bits (set) 23 pcs
• Adapter 1 / 4’’HEX to 5 / 32’’HEX 1 pc
• Package 1 pc
• Data line 1 pc
• Instruction manual 1 pc
• Note: Since the product is constantly being improved, P.I.T. reserves the right to make changes to the specifications and product specifications specifi ed here without prior notice.

Technical specifications

Tool elements

1. Bit holder
2. Lighting elements
3. Charging connector
4. Battery charge status indicator
5. Switch

Attention
Make sure the product and accessory kit are free of shipping damage.

Purpose and scope
The battery screwdriver is designed for screwing/ unscrewing screws, self- tapping screws and screws using the appropriate attachments. Please read this manual carefully, including the section on Safety Instructions and the General Safety Instructions Appendix. This is the only way you can learn how to handle the product correctly and avoid mistakes and dangerous situations. The product is intended for use in areas with a temperate climate with a characteristic temperature from 0 ° C to +40 ° C, relative air humidity not more than 80% and the absence of direct exposure to atmospheric precipitation and excessive dustiness of the air.

The product meets the requirements:

• Technical Regulations of the Customs Union TR CU 004/2011 “On the safety of low-voltage equipment”;
• TR CU 020/2011 “Electromagnetic com patibility of technical equipment”.
• In connection with the continued work on improving the product, the manufacturer reserves the right to make minor changes to its design that are not reflected in this manual and do not aff ect the effi cient and safe operation of the product.

Recommendations for use
Provide good lighting for your work area. The LED is auxiliary and is intended for illumination in hard-to-reach places or in the absence of lighting. To avoid overheating, take breaks in the operation of the product. Intensive use and increased loads reduce the service life of the product. When the battery is discharged, the torque generated by it decreases. Therefore, when
twisting or unscrewing the next fastener, with an increase in resistance, the engine, being energized, will stop. This mode is a short circuit for the electric motor and can damage the motor and the battery. To avoid product damage, DO NOT ALLOW this operation.

To avoid damage to the battery, DO NOT STORE the product with a discharged battery. Charge the battery FULLY after use. Check the good condition of the product. If you fi nd something abnormal in the operation of the product, immediately stop using it. Due to the technical complexity of the product, the limit state criteria cannot be determined by the user independently. In the case of an apparent or suspected malfunction, refer to the “Possible malfunctions and remedies” section.

If the malfunction is not in the list or you were unable to eliminate it, contact a specialized service center. The service center issues a conclusion on the limiting state of the product or its parts in the form of the corresponding Act.

Safety rules
Before starting work, please check and visually inspect the product for obvious mechanical damage. Do not disassemble or modify the product, and do not replace individual parts. To avoid damage to the battery, do not store the battery in a discharged state. Please FULLY charge the battery after use. During work, replaceable tools may overheat. Wait until necessary to cool down, or wear protective gloves. When rotating manually, do not exceed the torque specifi ed in the technical data.

Conditions for transportation, storage
Store and transport in the manufacturer’s packaging, in a clean form, in a dry ventilated room, away from sources of heat. Avoid moisture, exposure to direct sunlight. Dispose of the old product, accessories and packaging in an environmentally friendly manner in accordance with local disposal regulations. Maintenance and Service

Maintenance and Cleaning

• Before any work on the machine itself (e. g. maintenance, tool change, etc.) as well as during transport and storage, remove the battery from the power tool. There is danger of injury when unintentionally actuating the On/Off switch.
• For safe and proper working, always keep the machine and ventilation slots clean. When the battery is no longer operative, please refer to an authorized after-sales service agent for P.I.T. power tools.

Dispose of waste
Damaged power tools, batteries, accessories and waste packaging materials must be recycled and reused in an environmentally friendly manner. Do not throw power tools and accumulators / batteries into general household waste! Product serial number interpretation serial number.

The date of manufacture of the product is encoded in the serial number printed on the body of the tool. The fi rst 2 digits indicate the year of issue, the next 2 digits indicate the month.

TERMS OF WARRANTY SERVICE

1. This Warranty Certifi cate is the only document that confi rms your right to free warranty service. Without presenting this certifi cate, no claims are accepted. In case of loss or damage, the warranty certifi cate is not restored.

2. The warranty period for the electric machine is 12 months from the date of sale, during the warranty period the service department eliminates manufacturing defects and replaces parts that have failed due to the fault of the manufacturer free of charge. In the warranty repair, an equivalent operable product is not provided. Replaceable parts become property of service providers. P.I.T is not liable for any damage that may be caused by operation of the electric machine.

3. Only clean tool accompanied with the following duly executed documents: this Warranty Certificate, Warranty Card, with all fi elds fi lled out, bearing the stamp of the trade organization and the signature of the buyer, shall be accepted for warranty repair.

4. Warranty repair is not performed in the following cases:

   • in the absence of a Warranty Certifi cate and a Warranty Card or their incorrect execution;

   • with failure of both a rotor and a stator of the electric engine, charring or melting of primary winding of the welding machine transformer, charging or starting-charging device, with internal parts melting, burn down of electronic circuit boards;

   • if a Warranty Certifi cate or a Warranty Card does not correspond to this electric machine or to the form established by the supplier;

   • upon expiration of the warranty period;

   • at attempts of opening or repair of the electric machine outside the warranty workshop; making constructive changes and lubrication of the tool during the warranty period, as evidenced, for example, by the creases on the spline parts of the fasteners of non-rotational parts.when using electric tools for production or
     other purposes connected with making a profit, as well as in case of malfunctions related to instability of the power network parameters exceeding the norms established by GOST;

   • in the events of improper operation (use the electric machine for other than intended purposes, attachments to the electric machine of attachments, accessories, etc. not provided by the manufacturer);

   • with mechanical damage to the case, power cord and in case of damages caused by aggressive agents and high and low temperatures, ingress of foreign objects in the ventilation grids of the electric machine, as well as in case of damage resulting from improper storage (corrosion of metal parts);

   • natural wear and tear on the parts of the electric machine, as a result of long-term operation (determined on the basis of the signs of full or partial depletion of the specified mean life, great contamination, presence of rust outside and inside the electric machine, waste lubricant in the gearbox);

   • use of the tool the purposes for other than specified in the operating instructions.

   • mechanical damages to the tool;

   • in the event of damages due to non-observance of the operating conditions specifi ed in the instruction (see chapter “Safety Precautions” of the Manual).

   • damage to the product due to non-observance of the rules of storage and transportation. Preventive maintenance of electric machines (cleaning, washing, lubrication, replacement of anthers, piston and sealing rings) during the warranty period is a paid service. The service life of the product is 3 years. Shelf life is 2 years. It is not recommended for operation
     after 2 years of storage from the date of manufacture, which is indicated in the serial number on the label of the instrument, without preliminary verifi cation (for the defi nition of the date of manufacture, see the User’s Manual earlier). The owner is notified of any possible violations
     of the above terms of wa rranty service upon completion of diagnostics in the service center. The owner of the tool entrusts the diagnostic procedure to be conducted in the service center in his absence. Do not operate the electric machine when there are signs of excessive heat, sparking, or noise in the gearbox. To determine the cause of the malfunction, the buyer should contactthe warranty service center. Malfunctions caused by late replacement of carbon brushes of the engine are eliminated at the expense of the buyer.

5. The warranty does not cover:

   • replacement accessories (accessories and components), for example: batteries, discs, blades, drill bits, borers, chucks, chains, sprockets, collet clamps, guide rails, tension and fastening elements, trimming device heads, base of grinding and belt sander machines, hexagonal heads, etc.,
   • fast wearing parts, for example: carbon brushes, drive belts, seals, protective covers, guiding rollers, guides, rubber seals, bearings, toothed belts and wheels, shanks, brake belts, starter ratchets and ropes, piston rings, etc. Their replacement during the warranty period is a paid service;
   • power cords, in case of damage to the insulation, power cords are subject to mandatory replacement without the consent of the owner.

Hangzhou Gongxuan Science & Technology Co., Ltd.
Address: Room 2-1504, Jiabao Scientific Innovation Center, 519 No. 2 Road, Baiyang Street, Qiantang District, Hangzhou City, Zhejiang Province, China.
E-mail: online@pit-tools.com
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>