WAGNER 2419967 EasyRoll Wall Roller User Manual

WAGNER 2419967 EasyRoll Wall Roller

Product Information

Specifications

• Product Name: EasyRoll
• Languages: DE, EN, FR, NL, IT, CS, SK, RO
• Dimensions: x5
• Weight: x5
• Warranty: 3+1 years

Product Usage Instructions

Before You Begin

CAUTION: You should only use the EasyRoll for diluted liquids and dilutable paints, such as water soluble, latex and  acrylic paints, as not all components are solvent resistant. To ensure as long a useful life as possible of your EasyRoll, it should be thoroughly cleaned immediately after each use.

Preparing the Workplace and the Paint

Before using the EasyRoll, make sure to prepare your workplace and the paint properly. Follow these steps:

1. Place the inner roll (Fig. 1, 1) in the roller cover (2) and close the roller cover with the two caps (3 and 4).
2. Push the roller handle (Fig. 2, 5) into the roller cover until it audibly engages.
3. Open the lever (Fig. 3, 6) and place the roller handle in the holder.
4. Secure the fill tube (Fig. 4) on the edge of the paint bucket and push the fill tube to the floor of the container.
5. Apply a little lubricating grease to the fill tube so that it can be inserted more easily into the fill valve. (Fig. 4, 7)
6. Press down and firmly hold the fill valve of the main tube onto the fill tube. Pull the plunger to draw the paint into the main tube. (Fig.5)
7. Push plunger tube forward until you see paint coming through the roller cover.
8. Start rolling. Squeeze trigger for additional paint as needed. Do not oversaturate the roller. Refill EasyRoll as necessary to complete the project.
9. During extended break periods, wrap your roller cover in a plastic bag to keep it from drying out.

Cleanup

When cleaning the EasyRoll, you must use the appropriate cleaning solution for the type of paint you are using.

FAQ

Q: What types of paints can I use with EasyRoll?A: You should only use diluted liquids and dilutable paints, such as water-soluble, latex, and acrylic paints.Q: How should I clean the EasyRoll?A: Use the appropriate cleaning solution for the type of paint you are using.Q: How long is the warranty for EasyRoll?A: The warranty is 3+1 years. Please refer to our website or authorized WAGNER partners for detailed warranty conditions.

BEFORE YOU BEGIN

CAUTION :
You should only use the EasyRoll for diluted liquids and dilutable paints, such as water soluble, latex and acrylic paints, as not all components are solvent resistant. To ensure as long a useful life as possible of your EasyRoll,  it should be thoroughly cleaned immediately after each use.

PREPARING THE WORKPLACE AND THE PAINT

• Before beginning work, cover or tape up the floor, furniture, door frames and other objects.
• Place the unit on a suffifficiently sized piece of plastic or cardboard.
• Stir the paint well and thin up to 10 % if necessary (observe information from manufacturer).

START-UP

Depending on the version, EasyRoll comes already pre-assembled. If it is  not, please follow the steps below.

1. Place the inner roll (Fig. 1, 1) in the roller cover (2) and close the roller cover with the  two caps (3 and 4).
2. Push the roller handle (Fig. 2, 5) into the roller cover until it audibly engages.
3. Open the lever (Fig. 3, 6) and place the roller handle in the holder.
4. Secure the fill tube (Fig. 4) on the edge of the paint bucket and push the fill tube all the way to the floor of the container.
5. Apply a little lubricating grease to the fill tube so that it can be inserted more easily  into the fill valve. (Fig. 4, 7)
6. Press down and firmly hold the fill valve of the main tube onto the fill tube. Pull the plunger to draw the paint into the main tube. (Fig. 5)
7. Push plunger tube forward until you see paint coming through the roller cover.
8. Begin rolling. Squeeze trigger for additional paint as needed.

Do not oversaturate the roller. Refifill EasyRoll as necessary to complete project. During extended break periods, wrap your roller cover in a plastic bag to keep it from drying out.

CLEANUP

When cleaning the EasyRoll, you must use the appropriate cleaning solution for the type of paint you are using.

1. Pull the plunger back to draw the remaining paint from roller arm into the tube.(Fig. 5)
2. Press fill valve onto fill tube. (Fig. 8) Push plunger forward to return excess paint to can.
3. Pull the color roller off the roller handle. (Fig. 9). If necessary, tap lightly on the edge of the colour roller to release it. Take care not to knock the inner cap since doing so  could cause damage.
4. Lever the two caps out of the roller cover using the roller handle. (Fig. 10).
5. Push the inner roller out of the roller cover. (Fig. 11).
6. Clean the roller cover, inner roller and caps with water.
7. Clean the fill tube, roller arm and fill valve in sequence by immersing the components in a bucket of water and moving the piston rod back and forth around 5 times. (Fig.  12, 13 and 14)

STORAGE

1. Turn the locking collar next to the trigger counterclockwise (fig. 15) until the main tube slides off the plunger.
2. Pack a generous amount of petroleum jelly around and in between the O-rings on the plunger. (Fig. 16)
3. Clean and pack a generous amount of petroleum jelly on the indicated bearing areas of the arm. (Fig. 17)
4. Grease the two caps and put the roller cover and roller arm back together. (Fig. 18)

is backward

2. Parts or connecting points of the roller not properly cleaned

3. Paint residue on connecting areas

4. The roller cover is worn or damaged

5. The inner roller or sealing cap is worn or damaged

6)  The bearing areas are worn

| 1)   Turn the seal around

2. Clean and properly lubricate (see “Cleanup” and “Storage” sections)

3)  Clean connecting areas

4)  Replace roller cover

5. Replace the inner roller or sealing cap

6)  Call customer service

B. Plunger is difficult to pull/push| 1) O-rings are not lubricated| 1) Lubricate the O-rings on the plunger
C. The fill tube will not fill with paint or paint leaks from fill valve| 1) Paint residue on fill valve components| 1) Insert fill tube firmly into fill valve and twist fill tube several times to break up paint residue.

2. If the problem persists, refer to the steps below to clean the fill valve

components.

OVERVIEW

1. Unscrew the locking cap (a) on the valve housing  by turning counterclockwise.
2. Remove the retaining disk (b) and the duckbill valve  (c) from the valve housing
3. Clean these parts thoroughly using water.
4. Allow all parts to dry before reassembling.
5. Grease the tip of the rubber valve (c) with Vaseline.
6. Replace the duckbill valve (c) and retainer disk (b).
7. Screw the locking cap (a) on the valve housing by  turning it counterclockwise

Parts List (Fig. 19)

Item| Description| Part No.| Qty.
1,3,5| Roller core and cap| 2422071| 1
2| Roller cover 12 mm

Roller cover 20 mm (accessories)

| 0998230

0245717

| 1

1

4| Roller arm| 2422073| 1
6,7,8| Locking cap, retainer disk, duckbill valve| 2441879| 1
9| O-ring| 2326966| 2
10| Suction system| 2423178| 1

NOTICE : If after extended use you find the plunger difficult to pull while filling, apply a generous amount of petroleum jelly around the o-rings located at the end of the plunger. We have included a packet of petroleum jelly for you convenience.

Important Note regarding Product Liability!
Due to an EC ordinance in effect since 01.01.1990, the manufacturer is liable for his product only if all parts originate from or were approved by the manufacturer and the devices  are assembled and operated correctly. The use of other accessories and spare parts can partially or completely invalidate the liability.

3 + 1 year guarantee on this WAGNER DIY product

In addition to the statutory warranty for this product, J. Wagner GmbH, based in 88677 Markdorf, Germany, grants you a guarantee (device guarantee) of 36 months for this product. This guarantee is extended by a further 12 months if the product is registered within 28 days of purchase on the Internet at https://go.wagner-group.com/3plus1.
The guarantee includes the free repair of defects that are demonstrably caused by the use of unsuitable materials in the product’s manufacture or by assembly errors, as well as the free replacement of faulty components provided there are no guarantee exclusions.
The statutory material defect rights to which you as the purchaser are entitled for the intended purpose from the time of handover of the purchased item are not restricted by the guarantee. The guarantee, along with your statutory warranty rights, will expire if the device has been opened by persons other than authorized WAGNER service personnel.
The detailed guarantee conditions can be obtained on request from our authorised WAGNER partners (see website or operating instructions) or in text form on our website: https://go.wagner-group.com/hf-warranty- conditions

Modifications reserved

J. WAGNER
GMBH Otto-Lilienthal-Str. 18  88677 Markdorf
T +49 0180 – 55 92 46 37
F +49 075 44 -5 05 11 69
UK IMPORTER
WAGNER SPRAYTECH (UK) LTD
Innovation Centre Silverstone Park, Silverstone Northants NN12 8GX
T + 44 (0) 1327 368410
WAGNER FRANCE
S.A.R.L. 12 Avenue des Tropiques  Z.A. de Courtaboeuf 91978 Les Ulis Cedex
T +33 0825 011 111
F +33 (0) 1 69 81 72 57
FHC SRL
Via Stazione 94, 26013 Crema (CR)
T 0373 204839
F 0373 204845
Not responsible for errors and changes.
© Copyright by J.Wagner GmbH

References

• WAGNER 3+1 Garantie
• Group Publishing
• WAGNER Group for industry, craftsmen & do-it-yourselfers | WAGNER
• WAGNER 3+1 Garantie

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>